mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-26 01:35:35 +07:00
1004a2977b
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND nodes along the way. Note that we keep using old bindings in at91rm9200.dtsi because this SoC is not supported by the EBI driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
136 lines
2.3 KiB
Plaintext
136 lines
2.3 KiB
Plaintext
/*
|
|
* usb_a926x.dts - Device Tree file for Caloa USB A926x board
|
|
*
|
|
* Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
*
|
|
* Licensed under GPLv2 or later.
|
|
*/
|
|
|
|
/ {
|
|
clocks {
|
|
slow_xtal {
|
|
clock-frequency = <32768>;
|
|
};
|
|
|
|
main_xtal {
|
|
clock-frequency = <12000000>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
apb {
|
|
dbgu: serial@fffff200 {
|
|
status = "okay";
|
|
};
|
|
|
|
macb0: ethernet@fffc4000 {
|
|
phy-mode = "rmii";
|
|
status = "okay";
|
|
};
|
|
|
|
usb1: gadget@fffa4000 {
|
|
atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
ebi: ebi@10000000 {
|
|
status = "okay";
|
|
|
|
nand_controller: nand-controller {
|
|
status = "okay";
|
|
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
|
|
pinctrl-names = "default";
|
|
|
|
nand@3 {
|
|
reg = <0x3 0x0 0x800000>;
|
|
rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
|
|
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "soft";
|
|
nand-on-flash-bbt;
|
|
label = "atmel_nand";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
at91bootstrap@0 {
|
|
label = "at91bootstrap";
|
|
reg = <0x0 0x20000>;
|
|
};
|
|
|
|
barebox@20000 {
|
|
label = "barebox";
|
|
reg = <0x20000 0x40000>;
|
|
};
|
|
|
|
bareboxenv@60000 {
|
|
label = "bareboxenv";
|
|
reg = <0x60000 0x20000>;
|
|
};
|
|
|
|
bareboxenv2@80000 {
|
|
label = "bareboxenv2";
|
|
reg = <0x80000 0x20000>;
|
|
};
|
|
|
|
oftree@80000 {
|
|
label = "oftree";
|
|
reg = <0xa0000 0x20000>;
|
|
};
|
|
|
|
kernel@a0000 {
|
|
label = "kernel";
|
|
reg = <0xc0000 0x400000>;
|
|
};
|
|
|
|
rootfs@4a0000 {
|
|
label = "rootfs";
|
|
reg = <0x4c0000 0x7800000>;
|
|
};
|
|
|
|
data@7ca0000 {
|
|
label = "data";
|
|
reg = <0x7cc0000 0x8340000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
usb0: ohci@500000 {
|
|
num-ports = <2>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
user_led {
|
|
label = "user_led";
|
|
gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
user_pb {
|
|
label = "user_pb";
|
|
gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
|
|
linux,code = <28>;
|
|
wakeup-source;
|
|
};
|
|
};
|
|
|
|
i2c-gpio-0 {
|
|
status = "okay";
|
|
};
|
|
};
|