AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-28 11:18:45 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
a5c66e4b24
linux_dsm_epyc7002/drivers/usb/misc/Kconfig
Tony Olech a5c66e4b24 USB: ftdi-elan: client driver for ELAN Uxxx adapters 
This "ftdi-elan" module is one half of the "driver" for
ELAN's Uxxx series adapters which are USB to PCMCIA CardBus
adapters. Currently only the U132 adapter is available and
it's module is called "u132-hcd".

When the USB hot plug subsystem detects a Uxxx series adapter
it should load this module.

Upon a successful device probe() the jtag device file interface
is created and the status workqueue started up.

The jtag device file interface exists for the purpose of
updating the firmware in the Uxxx series adapter, but as
yet it had never been used.

The status workqueue initializes the Uxxx and then sits there
polling the Uxxx until a supported PCMCIA CardBus device is
detected it will start the command and respond workqueues
and then load the module that handles the device. This will
initially be only the u132-hcd module. The status workqueue
then just polls the Uxxx looking for card ejects.

The command and respond workqueues implement a command
sequencer for communicating with the firmware on the other
side of the FTDI chip in the Uxxx. This "ftdi-elan" module
exports some functions to interface with the sequencer.

Note that this module is a USB client driver.

Note that the "u132-hcd" module is a (cut-down OHCI)
host controller.

Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.

Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27 11:58:59 -07:00

237 lines
7.5 KiB
Plaintext
Raw Blame History

#
# USB Miscellaneous driver configuration
#
comment "USB Miscellaneous drivers"
depends on USB
config USB_EMI62
tristate "EMI 6|2m USB Audio interface support"
depends on USB
---help---
This driver loads firmware to Emagic EMI 6|2m low latency USB
Audio and Midi interface.
After firmware load the device is handled with standard linux
USB Audio driver.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called audio. If you want to compile it as a
module, say M here and read <file:Documentation/kbuild/modules.txt>.
config USB_EMI26
tristate "EMI 2|6 USB Audio interface support"
depends on USB
---help---
This driver loads firmware to Emagic EMI 2|6 low latency USB
Audio interface.
After firmware load the device is handled with standard linux
USB Audio driver.
To compile this driver as a module, choose M here: the
module will be called emi26.
config USB_ADUTUX
tristate "ADU devices from Ontrak Control Systems (EXPERIMENTAL)"
depends on USB && EXPERIMENTAL
help
Say Y if you want to use an ADU device from Ontrak Control
Systems.
To compile this driver as a module, choose M here. The module
will be called adutux.
config USB_AUERSWALD
tristate "USB Auerswald ISDN support (EXPERIMENTAL)"
depends on USB && EXPERIMENTAL
help
Say Y here if you want to connect an Auerswald USB ISDN Device
to your computer's USB port.
To compile this driver as a module, choose M here: the
module will be called auerswald.
config USB_RIO500
tristate "USB Diamond Rio500 support (EXPERIMENTAL)"
depends on USB && EXPERIMENTAL
help
Say Y here if you want to connect a USB Rio500 mp3 player to your
computer's USB port. Please read <file:Documentation/usb/rio.txt>
for more information.
To compile this driver as a module, choose M here: the
module will be called rio500.
config USB_LEGOTOWER
tristate "USB Lego Infrared Tower support (EXPERIMENTAL)"
depends on USB && EXPERIMENTAL
help
Say Y here if you want to connect a USB Lego Infrared Tower to your
computer's USB port.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called legousbtower. If you want to compile it as
a module, say M here and read
<file:Documentation/kbuild/modules.txt>.
config USB_LCD
tristate "USB LCD driver support"
depends on USB
help
Say Y here if you want to connect an USBLCD to your computer's
USB port. The USBLCD is a small USB interface board for
alphanumeric LCD modules. See <http://www.usblcd.de/> for more
information.
To compile this driver as a module, choose M here: the
module will be called usblcd.
config USB_LED
tristate "USB LED driver support"
depends on USB
help
Say Y here if you want to connect an USBLED device to your
computer's USB port.
To compile this driver as a module, choose M here: the
module will be called usbled.
config USB_CYPRESS_CY7C63
tristate "Cypress CY7C63xxx USB driver support"
depends on USB
help
Say Y here if you want to connect a Cypress CY7C63xxx
micro controller to your computer's USB port. Currently this
driver supports the pre-programmed devices (incl. firmware)
by AK Modul-Bus Computer GmbH.
Please see: http://www.ak-modul-bus.de/stat/mikrocontroller.html
To compile this driver as a module, choose M here: the
module will be called cypress_cy7c63.
config USB_CYTHERM
tristate "Cypress USB thermometer driver support"
depends on USB
help
Say Y here if you want to connect a Cypress USB thermometer
device to your computer's USB port. This device is also known
as the Cypress USB Starter kit or demo board. The Elektor
magazine published a modified version of this device in issue
#291.
To compile this driver as a module, choose M here: the
module will be called cytherm.
config USB_PHIDGET
tristate "USB Phidgets drivers"
depends on USB
help
Say Y here to enable the various drivers for devices from
Phidgets inc.
config USB_PHIDGETKIT
tristate "USB PhidgetInterfaceKit support"
depends on USB_PHIDGET
help
Say Y here if you want to connect a PhidgetInterfaceKit USB device
from Phidgets Inc.
To compile this driver as a module, choose M here: the
module will be called phidgetkit.
config USB_PHIDGETMOTORCONTROL
tristate "USB PhidgetMotorControl support"
depends on USB_PHIDGET
help
Say Y here if you want to connect a PhidgetMotorControl USB device
from Phidgets Inc.
To compile this driver as a module, choose M here: the
module will be called phidgetmotorcontrol.
config USB_PHIDGETSERVO
tristate "USB PhidgetServo support"
depends on USB_PHIDGET
help
Say Y here if you want to connect an 1 or 4 Motor PhidgetServo
servo controller version 2.0 or 3.0.
Phidgets Inc. has a web page at <http://www.phidgets.com/>.
To compile this driver as a module, choose M here: the
module will be called phidgetservo.
config USB_IDMOUSE
tristate "Siemens ID USB Mouse Fingerprint sensor support"
depends on USB
help
Say Y here if you want to use the fingerprint sensor on
the Siemens ID Mouse. There is also a Siemens ID Mouse
_Professional_, which has not been tested with this driver,
but uses the same sensor and may therefore work.
This driver creates an entry "/dev/idmouseX" or "/dev/usb/idmouseX",
which can be used by, e.g.,"cat /dev/idmouse0 > fingerprint.pnm".
See also <http://www.fs.tum.de/~echtler/idmouse/>.
config USB_FTDI_ELAN
tristate "Elan PCMCIA CardBus Adapter USB Client"
depends on USB
default M
help
ELAN's Uxxx series of adapters are USB to PCMCIA CardBus adapters.
Currently only the U132 adapter is available.
The U132 is specifically designed for CardBus PC cards that contain
an OHCI host controller. Typical PC cards are the Orange Mobile 3G
Option GlobeTrotter Fusion card. The U132 adapter will *NOT* work
with PC cards that do not contain an OHCI controller. To use a U132
adapter you will need this "ftdi-elan" module as well as the "u132-hcd"
module which is a USB host controller driver that talks to the OHCI
controller within CardBus card that are inserted in the U132 adapter.
This driver has been tested with a CardBus OHCI USB adapter, and
worked with a USB PEN Drive inserted into the first USB port of
the PCCARD. A rather pointless thing to do, but useful for testing.
See also the USB_U132_HCD entry "Elan U132 Adapter Host Controller"
It is safe to say M here.
config USB_APPLEDISPLAY
tristate "Apple Cinema Display support"
depends on USB
select BACKLIGHT_LCD_SUPPORT
select BACKLIGHT_CLASS_DEVICE
help
Say Y here if you want to control the backlight of Apple Cinema
Displays over USB. This driver provides a sysfs interface.
source "drivers/usb/misc/sisusbvga/Kconfig"
config USB_LD
tristate "USB LD driver"
depends on USB
help
This driver is for generic USB devices that use interrupt transfers,
like LD Didactic's USB devices.
To compile this driver as a module, choose M here: the
module will be called ldusb.
config USB_TEST
tristate "USB testing driver (DEVELOPMENT)"
depends on USB && USB_DEVICEFS && EXPERIMENTAL
help
This driver is for testing host controller software. It is used
with specialized device firmware for regression and stress testing,
to help prevent problems from cropping up with "real" drivers.
See <http://www.linux-usb.org/usbtest/> for more information,
including sample test device firmware and "how to use it".
Reference in New Issue View Git Blame Copy Permalink