AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-28 11:18:45 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
a5c4c29d24
linux_dsm_epyc7002/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
Marek Szyprowski 1c226017d3
ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity 
Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2019-12-17 09:37:14 +01:00

465 lines
10 KiB
Plaintext
Raw Blame History

/*
* Copyright 2015 Chen-Yu Tsai
*
* Chen-Yu Tsai <wens@csie.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-a83t.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Cubietech Cubietruck Plus";
compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
blue {
label = "cubietruck-plus:blue:usr";
gpios = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
};
orange {
label = "cubietruck-plus:orange:usr";
gpios = <&pio 3 26 GPIO_ACTIVE_HIGH>; /* PD26 */
};
white {
label = "cubietruck-plus:white:usr";
gpios = <&pio 3 27 GPIO_ACTIVE_HIGH>; /* PD27 */
};
green {
label = "cubietruck-plus:green:usr";
gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
};
};
usb-hub {
/* I2C is not connected */
compatible = "smsc,usb3503";
initial-mode = <1>; /* initialize in HUB mode */
disabled-ports = <1>;
intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
refclk-frequency = <19200000>;
};
reg_usb1_vbus: reg-usb1-vbus {
compatible = "regulator-fixed";
regulator-name = "usb1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
enable-active-high;
gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */
};
reg_usb2_vbus: reg-usb2-vbus {
compatible = "regulator-fixed";
regulator-name = "usb2-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
enable-active-high;
gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
};
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "On-board SPDIF";
simple-audio-card,cpu {
sound-dai = <&spdif>;
};
simple-audio-card,codec {
sound-dai = <&spdif_out>;
};
};
spdif_out: spdif-out {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&ac100_rtc 1>;
clock-names = "ext_clock";
/* The WiFi low power clock must be 32768 Hz */
assigned-clocks = <&ac100_rtc 1>;
assigned-clock-rates = <32768>;
/* enables internal regulator and de-asserts reset */
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
};
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&cpu100 {
cpu-supply = <&reg_dcdc3>;
};
&de {
status = "okay";
};
&ehci0 {
/* GL830 USB-to-SATA bridge here */
status = "okay";
};
&ehci1 {
/* USB3503 HSIC USB 2.0 hub here */
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <&reg_dldo4>;
phy-handle = <&rgmii_phy>;
phy-mode = "rgmii";
status = "okay";
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&mdio {
rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <&reg_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
vmmc-supply = <&reg_dcdc1>;
vqmmc-supply = <&reg_sw>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_emmc_pins>;
vmmc-supply = <&reg_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
&r_rsb {
status = "okay";
axp81x: pmic@3a3 {
compatible = "x-powers,axp818", "x-powers,axp813";
reg = <0x3a3>;
interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
eldoin-supply = <&reg_dcdc1>;
swin-supply = <&reg_dcdc1>;
x-powers,drive-vbus-en;
};
ac100: codec@e89 {
compatible = "x-powers,ac100";
reg = <0xe89>;
ac100_codec: codec {
compatible = "x-powers,ac100-codec";
interrupt-parent = <&r_pio>;
interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
#clock-cells = <0>;
clock-output-names = "4M_adda";
};
ac100_rtc: rtc {
compatible = "x-powers,ac100-rtc";
interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
clocks = <&ac100_codec>;
#clock-cells = <1>;
clock-output-names = "cko1_rtc",
"cko2_rtc",
"cko3_rtc";
};
};
};
#include "axp81x.dtsi"
&ac_power_supply {
status = "okay";
};
&battery_power_supply {
status = "okay";
};
&reg_aldo1 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-1v8";
};
&reg_aldo2 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "dram-pll";
};
&reg_aldo3 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
&reg_dcdc1 {
/*
* The schematics say this should be 3.3V, but the FEX file says
* it should be 3V. The latter makes sense, as the WiFi module's
* I/O is indirectly powered from DCDC1, through SW. It is rated
* at 2.98V maximum.
*/
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-3v";
};
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpua";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpub";
};
&reg_dcdc4 {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-gpu";
};
&reg_dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vcc-dram";
};
&reg_dcdc6 {
regulator-always-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
regulator-name = "vdd-sys";
};
&reg_dldo2 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "dp-pwr";
};
&reg_dldo3 {
regulator-always-on;
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
regulator-name = "ephy-io";
};
&reg_dldo4 {
/*
* The PHY requires 20ms after all voltages are applied until core
* logic is ready and 30ms after the reset pin is de-asserted.
* Set a 100ms delay to account for PMIC ramp time and board traces.
*/
regulator-enable-ramp-delay = <100000>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "ephy";
};
&reg_drivevbus {
regulator-name = "usb0-vbus";
status = "okay";
};
&reg_eldo1 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "dp-bridge-1";
};
&reg_eldo2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "dp-bridge-2";
};
&reg_fldo1 {
/* TODO should be handled by USB PHY */
regulator-always-on;
regulator-min-microvolt = <1080000>;
regulator-max-microvolt = <1320000>;
regulator-name = "vdd12-hsic";
};
&reg_fldo2 {
/*
* Despite the embedded CPUs core not being used in any way,
* this must remain on or the system will hang.
*/
regulator-always-on;
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpus";
};
&reg_rtc_ldo {
regulator-name = "vcc-rtc";
};
&reg_sw {
regulator-name = "vcc-wifi-io";
};
&spdif {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "brcm,bcm4330-bt";
clocks = <&ac100_rtc 1>;
clock-names = "lpo";
vbat-supply = <&reg_dcdc1>;
vddio-supply = <&reg_sw>;
device-wakeup-gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
host-wakeup-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
shutdown-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
};
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usbphy {
usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <&reg_drivevbus>;
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
Reference in New Issue View Git Blame Copy Permalink