mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-21 17:01:57 +07:00
0bc5f749bc
There's a SMSC USB2640 (USB hub & SD controller) connected to it, but the SD card slot footprint is unpopulated. Also connected to the hub is a SMSC LAN7500 gigabit ethernet adapter. Link: https://lore.kernel.org/r/20191220065314.237624-6-lkundrak@v3.sk Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: Olof Johansson <olof@lixom.net>
117 lines
1.7 KiB
Plaintext
117 lines
1.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/*
|
|
* Dell Wyse 3020 a.k.a. "Ariel" a.k.a. Tx0D (T00D, T10D)
|
|
*
|
|
* Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk>
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "mmp3.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
/ {
|
|
model = "Dell Ariel";
|
|
compatible = "dell,wyse-ariel", "marvell,mmp3";
|
|
|
|
aliases {
|
|
serial2 = &uart3;
|
|
};
|
|
|
|
chosen {
|
|
#address-cells = <0x1>;
|
|
#size-cells = <0x1>;
|
|
ranges;
|
|
bootargs = "earlyprintk=ttyS2,115200 console=ttyS2,115200";
|
|
};
|
|
|
|
memory@0 {
|
|
linux,usable-memory = <0x0 0x7f600000>;
|
|
available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>;
|
|
reg = <0x0 0x80000000>;
|
|
device_type = "memory";
|
|
};
|
|
};
|
|
|
|
&uart3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_otg0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_otg_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&hsic0 {
|
|
status = "okay";
|
|
|
|
usb1@1 {
|
|
compatible = "usb424,2640";
|
|
reg = <0x01>;
|
|
#address-cells = <0x01>;
|
|
#size-cells = <0x00>;
|
|
|
|
mass-storage@1 {
|
|
compatible = "usb424,4040";
|
|
reg = <0x01>;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|
|
|
|
&hsic_phy0 {
|
|
status = "okay";
|
|
reset-gpios = <&gpio 63 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&mmc3 {
|
|
status = "okay";
|
|
max-frequency = <50000000>;
|
|
status = "okay";
|
|
bus-width = <8>;
|
|
non-removable;
|
|
cap-mmc-highspeed;
|
|
};
|
|
|
|
&twsi1 {
|
|
status = "okay";
|
|
|
|
rtc@68 {
|
|
compatible = "dallas,ds1338";
|
|
reg = <0x68>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&twsi3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&twsi4 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ssp3 {
|
|
status = "okay";
|
|
cs-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
|
|
|
|
firmware-flash@0 {
|
|
compatible = "st,m25p80", "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
m25p,fast-read;
|
|
};
|
|
};
|
|
|
|
&ssp4 {
|
|
cs-gpios = <&gpio 56 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|