mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-24 03:07:29 +07:00
b93427b1c0
The fsl_ssi driver only checks for the ac97 mode property, so remove the unused ones. Suggested-by: Nicolin Chen <nicoleotsuka@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Timur Tabi <timur@tabi.org> Signed-off-by: Mark Brown <broonie@kernel.org>
88 lines
4.6 KiB
Plaintext
88 lines
4.6 KiB
Plaintext
Freescale Synchronous Serial Interface
|
|
|
|
The SSI is a serial device that communicates with audio codecs. It can
|
|
be programmed in AC97, I2S, left-justified, or right-justified modes.
|
|
|
|
Required properties:
|
|
- compatible: Compatible list, should contain one of the following
|
|
compatibles:
|
|
fsl,mpc8610-ssi
|
|
fsl,imx51-ssi
|
|
fsl,imx35-ssi
|
|
fsl,imx21-ssi
|
|
- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on.
|
|
- reg: Offset and length of the register set for the device.
|
|
- interrupts: <a b> where a is the interrupt number and b is a
|
|
field that represents an encoding of the sense and
|
|
level information for the interrupt. This should be
|
|
encoded based on the information in section 2)
|
|
depending on the type of interrupt controller you
|
|
have.
|
|
- interrupt-parent: The phandle for the interrupt controller that
|
|
services interrupts for this device.
|
|
- fsl,playback-dma: Phandle to a node for the DMA channel to use for
|
|
playback of audio. This is typically dictated by SOC
|
|
design. See the notes below.
|
|
- fsl,capture-dma: Phandle to a node for the DMA channel to use for
|
|
capture (recording) of audio. This is typically dictated
|
|
by SOC design. See the notes below.
|
|
- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs.
|
|
This number is the maximum allowed value for SFCSR[TFWM0].
|
|
- fsl,ssi-asynchronous:
|
|
If specified, the SSI is to be programmed in asynchronous
|
|
mode. In this mode, pins SRCK, STCK, SRFS, and STFS must
|
|
all be connected to valid signals. In synchronous mode,
|
|
SRCK and SRFS are ignored. Asynchronous mode allows
|
|
playback and capture to use different sample sizes and
|
|
sample rates. Some drivers may require that SRCK and STCK
|
|
be connected together, and SRFS and STFS be connected
|
|
together. This would still allow different sample sizes,
|
|
but not different sample rates.
|
|
- clocks: "ipg" - Required clock for the SSI unit
|
|
"baud" - Required clock for SSI master mode. Otherwise this
|
|
clock is not used
|
|
|
|
Required are also ac97 link bindings if ac97 is used. See
|
|
Documentation/devicetree/bindings/sound/soc-ac97link.txt for the necessary
|
|
bindings.
|
|
|
|
Optional properties:
|
|
- codec-handle: Phandle to a 'codec' node that defines an audio
|
|
codec connected to this SSI. This node is typically
|
|
a child of an I2C or other control node.
|
|
- fsl,fiq-stream-filter: Bool property. Disabled DMA and use FIQ instead to
|
|
filter the codec stream. This is necessary for some boards
|
|
where an incompatible codec is connected to this SSI, e.g.
|
|
on pca100 and pcm043.
|
|
- dmas: Generic dma devicetree binding as described in
|
|
Documentation/devicetree/bindings/dma/dma.txt.
|
|
- dma-names: Two dmas have to be defined, "tx" and "rx", if fsl,imx-fiq
|
|
is not defined.
|
|
- fsl,mode: The operating mode for the AC97 interface only.
|
|
"ac97-slave" - AC97 mode, SSI is clock slave
|
|
"ac97-master" - AC97 mode, SSI is clock master
|
|
|
|
Child 'codec' node required properties:
|
|
- compatible: Compatible list, contains the name of the codec
|
|
|
|
Child 'codec' node optional properties:
|
|
- clock-frequency: The frequency of the input clock, which typically comes
|
|
from an on-board dedicated oscillator.
|
|
|
|
Notes on fsl,playback-dma and fsl,capture-dma:
|
|
|
|
On SOCs that have an SSI, specific DMA channels are hard-wired for playback
|
|
and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for
|
|
playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for
|
|
playback and DMA channel 3 for capture. The developer can choose which
|
|
DMA controller to use, but the channels themselves are hard-wired. The
|
|
purpose of these two properties is to represent this hardware design.
|
|
|
|
The device tree nodes for the DMA channels that are referenced by
|
|
"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with
|
|
"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g.
|
|
"fsl,mpc8610-dma-channel") can remain. If these nodes are left as
|
|
"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA
|
|
drivers (fsldma) will attempt to use them, and it will conflict with the
|
|
sound drivers.
|