mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-05 09:26:44 +07:00
6ab3d5624e
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
153 lines
5.3 KiB
C
153 lines
5.3 KiB
C
/*
|
|
* m32r_sio_reg.h
|
|
*
|
|
* Copyright (C) 1992, 1994 by Theodore Ts'o.
|
|
* Copyright (C) 2004 Hirokazu Takata <takata at linux-m32r.org>
|
|
*
|
|
* Redistribution of this file is permitted under the terms of the GNU
|
|
* Public License (GPL)
|
|
*
|
|
* These are the UART port assignments, expressed as offsets from the base
|
|
* register. These assignments should hold for any serial port based on
|
|
* a 8250, 16450, or 16550(A).
|
|
*/
|
|
|
|
#ifndef _M32R_SIO_REG_H
|
|
#define _M32R_SIO_REG_H
|
|
|
|
|
|
#ifdef CONFIG_SERIAL_M32R_PLDSIO
|
|
|
|
#define SIOCR 0x000
|
|
#define SIOMOD0 0x002
|
|
#define SIOMOD1 0x004
|
|
#define SIOSTS 0x006
|
|
#define SIOTRCR 0x008
|
|
#define SIOBAUR 0x00a
|
|
// #define SIORBAUR 0x018
|
|
#define SIOTXB 0x00c
|
|
#define SIORXB 0x00e
|
|
|
|
#define UART_RX ((unsigned long) PLD_ESIO0RXB)
|
|
/* In: Receive buffer (DLAB=0) */
|
|
#define UART_TX ((unsigned long) PLD_ESIO0TXB)
|
|
/* Out: Transmit buffer (DLAB=0) */
|
|
#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
|
|
#define UART_TRG 0 /* (LCR=BF) FCTR bit 7 selects Rx or Tx
|
|
* In: Fifo count
|
|
* Out: Fifo custom trigger levels
|
|
* XR16C85x only */
|
|
|
|
#define UART_DLM 0 /* Out: Divisor Latch High (DLAB=1) */
|
|
#define UART_IER ((unsigned long) PLD_ESIO0INTCR)
|
|
/* Out: Interrupt Enable Register */
|
|
#define UART_FCTR 0 /* (LCR=BF) Feature Control Register
|
|
* XR16C85x only */
|
|
|
|
#define UART_IIR 0 /* In: Interrupt ID Register */
|
|
#define UART_FCR 0 /* Out: FIFO Control Register */
|
|
#define UART_EFR 0 /* I/O: Extended Features Register */
|
|
/* (DLAB=1, 16C660 only) */
|
|
|
|
#define UART_LCR 0 /* Out: Line Control Register */
|
|
#define UART_MCR 0 /* Out: Modem Control Register */
|
|
#define UART_LSR ((unsigned long) PLD_ESIO0STS)
|
|
/* In: Line Status Register */
|
|
#define UART_MSR 0 /* In: Modem Status Register */
|
|
#define UART_SCR 0 /* I/O: Scratch Register */
|
|
#define UART_EMSR 0 /* (LCR=BF) Extended Mode Select Register
|
|
* FCTR bit 6 selects SCR or EMSR
|
|
* XR16c85x only */
|
|
|
|
#else /* not CONFIG_SERIAL_M32R_PLDSIO */
|
|
|
|
#define SIOCR 0x000
|
|
#define SIOMOD0 0x004
|
|
#define SIOMOD1 0x008
|
|
#define SIOSTS 0x00c
|
|
#define SIOTRCR 0x010
|
|
#define SIOBAUR 0x014
|
|
#define SIORBAUR 0x018
|
|
#define SIOTXB 0x01c
|
|
#define SIORXB 0x020
|
|
|
|
#define UART_RX M32R_SIO0_RXB_PORTL /* In: Receive buffer (DLAB=0) */
|
|
#define UART_TX M32R_SIO0_TXB_PORTL /* Out: Transmit buffer (DLAB=0) */
|
|
#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
|
|
#define UART_TRG 0 /* (LCR=BF) FCTR bit 7 selects Rx or Tx
|
|
* In: Fifo count
|
|
* Out: Fifo custom trigger levels
|
|
* XR16C85x only */
|
|
|
|
#define UART_DLM 0 /* Out: Divisor Latch High (DLAB=1) */
|
|
#define UART_IER M32R_SIO0_TRCR_PORTL /* Out: Interrupt Enable Register */
|
|
#define UART_FCTR 0 /* (LCR=BF) Feature Control Register
|
|
* XR16C85x only */
|
|
|
|
#define UART_IIR 0 /* In: Interrupt ID Register */
|
|
#define UART_FCR 0 /* Out: FIFO Control Register */
|
|
#define UART_EFR 0 /* I/O: Extended Features Register */
|
|
/* (DLAB=1, 16C660 only) */
|
|
|
|
#define UART_LCR 0 /* Out: Line Control Register */
|
|
#define UART_MCR 0 /* Out: Modem Control Register */
|
|
#define UART_LSR M32R_SIO0_STS_PORTL /* In: Line Status Register */
|
|
#define UART_MSR 0 /* In: Modem Status Register */
|
|
#define UART_SCR 0 /* I/O: Scratch Register */
|
|
#define UART_EMSR 0 /* (LCR=BF) Extended Mode Select Register
|
|
* FCTR bit 6 selects SCR or EMSR
|
|
* XR16c85x only */
|
|
|
|
#endif /* CONFIG_SERIAL_M32R_PLDSIO */
|
|
|
|
#define UART_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
|
|
|
|
/*
|
|
* These are the definitions for the Line Control Register
|
|
*
|
|
* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
|
|
* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
|
|
*/
|
|
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
|
|
#define UART_LCR_SBC 0x40 /* Set break control */
|
|
#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
|
|
#define UART_LCR_EPAR 0x10 /* Even parity select */
|
|
#define UART_LCR_PARITY 0x08 /* Parity Enable */
|
|
#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
|
|
#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
|
|
#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
|
|
#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
|
|
#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
|
|
|
|
/*
|
|
* These are the definitions for the Line Status Register
|
|
*/
|
|
#define UART_LSR_TEMT 0x02 /* Transmitter empty */
|
|
#define UART_LSR_THRE 0x01 /* Transmit-hold-register empty */
|
|
#define UART_LSR_BI 0x00 /* Break interrupt indicator */
|
|
#define UART_LSR_FE 0x80 /* Frame error indicator */
|
|
#define UART_LSR_PE 0x40 /* Parity error indicator */
|
|
#define UART_LSR_OE 0x20 /* Overrun error indicator */
|
|
#define UART_LSR_DR 0x04 /* Receiver data ready */
|
|
|
|
/*
|
|
* These are the definitions for the Interrupt Identification Register
|
|
*/
|
|
#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
|
|
#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
|
|
|
|
#define UART_IIR_MSI 0x00 /* Modem status interrupt */
|
|
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
|
|
#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
|
|
#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
|
|
|
|
/*
|
|
* These are the definitions for the Interrupt Enable Register
|
|
*/
|
|
#define UART_IER_MSI 0x00 /* Enable Modem status interrupt */
|
|
#define UART_IER_RLSI 0x08 /* Enable receiver line status interrupt */
|
|
#define UART_IER_THRI 0x03 /* Enable Transmitter holding register int. */
|
|
#define UART_IER_RDI 0x04 /* Enable receiver data interrupt */
|
|
|
|
#endif /* _M32R_SIO_REG_H */
|