mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
4da722ca19
Pretty much any node can have a status property, so it doesn't need to be in examples. Converted with the following command and removed examples with SoC and board specific splits: git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d' Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rob Herring <robh@kernel.org>
75 lines
3.3 KiB
Plaintext
75 lines
3.3 KiB
Plaintext
NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver.
|
|
|
|
Required properties:
|
|
- compatible : For Tegra20, must be one of "nvidia,tegra20-i2c-dvc" or
|
|
"nvidia,tegra20-i2c". For Tegra30, must be "nvidia,tegra30-i2c".
|
|
For Tegra114, must be "nvidia,tegra114-i2c". Otherwise, must be
|
|
"nvidia,<chip>-i2c", plus at least one of the above, where <chip> is
|
|
tegra124, tegra132, or tegra210.
|
|
Details of compatible are as follows:
|
|
nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C
|
|
controller. This only support master mode of I2C communication. Register
|
|
interface/offset and interrupts handling are different than generic I2C
|
|
controller. Driver of DVC I2C controller is only compatible with
|
|
"nvidia,tegra20-i2c-dvc".
|
|
nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support
|
|
master and slave mode of I2C communication. The i2c-tegra driver only
|
|
support master mode of I2C communication. Driver of I2C controller is
|
|
only compatible with "nvidia,tegra20-i2c".
|
|
nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is
|
|
very much similar to Tegra20 I2C controller with additional feature:
|
|
Continue Transfer Support. This feature helps to implement M_NO_START
|
|
as per I2C core API transfer flags. Driver of I2C controller is
|
|
compatible with "nvidia,tegra30-i2c" to enable the continue transfer
|
|
support. This is also compatible with "nvidia,tegra20-i2c" without
|
|
continue transfer support.
|
|
nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is
|
|
very much similar to Tegra30 I2C controller with some hardware
|
|
modification:
|
|
- Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and
|
|
fast-clk. Tegra114 has only one clock source called as div-clk and
|
|
hence clock mechanism is changed in I2C controller.
|
|
- Tegra30/Tegra20 I2C controller has enabled per packet transfer by
|
|
default and there is no way to disable it. Tegra114 has this
|
|
interrupt disable by default and SW need to enable explicitly.
|
|
Due to above changes, Tegra114 I2C driver makes incompatible with
|
|
previous hardware driver. Hence, tegra114 I2C controller is compatible
|
|
with "nvidia,tegra114-i2c".
|
|
- reg: Should contain I2C controller registers physical address and length.
|
|
- interrupts: Should contain I2C controller interrupts.
|
|
- address-cells: Address cells for I2C device address.
|
|
- size-cells: Size of the I2C device address.
|
|
- clocks: Must contain an entry for each entry in clock-names.
|
|
See ../clocks/clock-bindings.txt for details.
|
|
- clock-names: Must include the following entries:
|
|
Tegra20/Tegra30:
|
|
- div-clk
|
|
- fast-clk
|
|
Tegra114:
|
|
- div-clk
|
|
- resets: Must contain an entry for each entry in reset-names.
|
|
See ../reset/reset.txt for details.
|
|
- reset-names: Must include the following entries:
|
|
- i2c
|
|
- dmas: Must contain an entry for each entry in clock-names.
|
|
See ../dma/dma.txt for details.
|
|
- dma-names: Must include the following entries:
|
|
- rx
|
|
- tx
|
|
|
|
Example:
|
|
|
|
i2c@7000c000 {
|
|
compatible = "nvidia,tegra20-i2c";
|
|
reg = <0x7000c000 0x100>;
|
|
interrupts = <0 38 0x04>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
clocks = <&tegra_car 12>, <&tegra_car 124>;
|
|
clock-names = "div-clk", "fast-clk";
|
|
resets = <&tegra_car 12>;
|
|
reset-names = "i2c";
|
|
dmas = <&apbdma 16>, <&apbdma 16>;
|
|
dma-names = "rx", "tx";
|
|
};
|