mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
791d3ef2e1
'interrupt-parent' is often documented as part of define bindings, but it is really outside the scope of a device binding. It's never required in a given node as it is often inherited from a parent node. Or it can be implicit if a parent node is an 'interrupt-controller' node. So remove it from all the binding files. Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org>
91 lines
3.5 KiB
Plaintext
91 lines
3.5 KiB
Plaintext
Hisilicon DSA Fabric device controller
|
|
|
|
Required properties:
|
|
- compatible: should be "hisilicon,hns-dsaf-v1" or "hisilicon,hns-dsaf-v2".
|
|
"hisilicon,hns-dsaf-v1" is for hip05.
|
|
"hisilicon,hns-dsaf-v2" is for Hi1610 and Hi1612.
|
|
- mode: dsa fabric mode string. only support one of dsaf modes like these:
|
|
"2port-64vf",
|
|
"6port-16rss",
|
|
"6port-16vf",
|
|
"single-port".
|
|
- interrupts: should contain the DSA Fabric and rcb interrupt.
|
|
- reg: specifies base physical address(es) and size of the device registers.
|
|
The first region is external interface control register base and size(optional,
|
|
only used when subctrl-syscon does not exist). It is recommended using
|
|
subctrl-syscon rather than this address.
|
|
The second region is SerDes base register and size(optional, only used when
|
|
serdes-syscon in port node does not exist). It is recommended using
|
|
serdes-syscon rather than this address.
|
|
The third region is the PPE register base and size.
|
|
The fourth region is dsa fabric base register and size. It is not required for
|
|
single-port mode.
|
|
- reg-names: may be ppe-base and(or) dsaf-base. It is used to find the
|
|
corresponding reg's index.
|
|
|
|
- phy-handle: phy handle of physical port, 0 if not any phy device. It is optional
|
|
attribute. If port node exists, phy-handle in each port node will be used.
|
|
see ethernet.txt [1].
|
|
- subctrl-syscon: is syscon handle for external interface control register.
|
|
- reset-field-offset: is offset of reset field. Its value depends on the hardware
|
|
user manual.
|
|
- buf-size: rx buffer size, should be 16-1024.
|
|
- desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096.
|
|
|
|
- port: subnodes of dsaf. A dsaf node may contain several port nodes(Depending
|
|
on mode of dsaf). Port node contain some attributes listed below:
|
|
- reg: is physical port index in one dsaf.
|
|
- phy-handle: phy handle of physical port. It is not required if there isn't
|
|
phy device. see ethernet.txt [1].
|
|
- serdes-syscon: is syscon handle for SerDes register.
|
|
- cpld-syscon: is syscon handle + register offset pair for cpld register. It is
|
|
not required if there isn't cpld device.
|
|
- port-rst-offset: is offset of reset field for each port in dsaf. Its value
|
|
depends on the hardware user manual.
|
|
- port-mode-offset: is offset of port mode field for each port in dsaf. Its
|
|
value depends on the hardware user manual.
|
|
- mc-mac-mask: mask of multicast address, determines bit in multicast address
|
|
to set:
|
|
1 stands for this bit will be precisely matched, TCAM will check this bit of
|
|
MAC address.
|
|
0 stands for this bit will be fuzzy matched, TCAM won't care about this bit
|
|
of MAC address.
|
|
|
|
[1] Documentation/devicetree/bindings/net/phy.txt
|
|
|
|
Example:
|
|
|
|
dsaf0: dsa@c7000000 {
|
|
compatible = "hisilicon,hns-dsaf-v1";
|
|
mode = "6port-16rss";
|
|
interrupt-parent = <&mbigen_dsa>;
|
|
reg = <0x0 0xc5000000 0x0 0x890000
|
|
0x0 0xc7000000 0x0 0x60000>;
|
|
reg-names = "ppe-base", "dsaf-base";
|
|
subctrl-syscon = <&subctrl>;
|
|
reset-field-offset = 0;
|
|
interrupts = <131 4>,<132 4>, <133 4>,<134 4>,
|
|
<135 4>,<136 4>, <137 4>,<138 4>,
|
|
<139 4>,<140 4>, <141 4>,<142 4>,
|
|
<143 4>,<144 4>, <145 4>,<146 4>,
|
|
<147 4>,<148 4>, <384 1>,<385 1>,
|
|
<386 1>,<387 1>, <388 1>,<389 1>,
|
|
<390 1>,<391 1>,
|
|
buf-size = <4096>;
|
|
desc-num = <1024>;
|
|
dma-coherent;
|
|
|
|
port@0 {
|
|
reg = 0;
|
|
phy-handle = <&phy0>;
|
|
serdes-syscon = <&serdes>;
|
|
mc-mac-mask = [ff f0 00 00 00 00];
|
|
};
|
|
|
|
port@1 {
|
|
reg = 1;
|
|
serdes-syscon = <&serdes>;
|
|
mc-mac-mask = [ff f0 00 00 00 00];
|
|
};
|
|
};
|