mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-26 18:30:54 +07:00
baeeb541e6
This adds the NAND flash controller (NFC) peripherial. The driver supports the SLC NAND chips found on Freescale's Vybrid Tower System Module. The Micron NAND chip on the module needs 4-bit ECC per 512 byte page. Use 24-bit ECC per 2k page, which is supported by the driver. Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
608 lines
15 KiB
Plaintext
608 lines
15 KiB
Plaintext
/*
|
|
* Copyright 2013 Freescale Semiconductor, Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*/
|
|
|
|
#include "vf610-pinfunc.h"
|
|
#include <dt-bindings/clock/vf610-clock.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
aliases {
|
|
can0 = &can0;
|
|
can1 = &can1;
|
|
serial0 = &uart0;
|
|
serial1 = &uart1;
|
|
serial2 = &uart2;
|
|
serial3 = &uart3;
|
|
serial4 = &uart4;
|
|
serial5 = &uart5;
|
|
gpio0 = &gpio0;
|
|
gpio1 = &gpio1;
|
|
gpio2 = &gpio2;
|
|
gpio3 = &gpio3;
|
|
gpio4 = &gpio4;
|
|
usbphy0 = &usbphy0;
|
|
usbphy1 = &usbphy1;
|
|
};
|
|
|
|
fxosc: fxosc {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <24000000>;
|
|
};
|
|
|
|
sxosc: sxosc {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <32768>;
|
|
};
|
|
|
|
reboot: syscon-reboot {
|
|
compatible = "syscon-reboot";
|
|
regmap = <&src>;
|
|
offset = <0x0>;
|
|
mask = <0x1000>;
|
|
};
|
|
|
|
soc {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "simple-bus";
|
|
interrupt-parent = <&mscm_ir>;
|
|
ranges;
|
|
|
|
aips0: aips-bus@40000000 {
|
|
compatible = "fsl,aips-bus", "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
mscm_cpucfg: cpucfg@40001000 {
|
|
compatible = "fsl,vf610-mscm-cpucfg", "syscon";
|
|
reg = <0x40001000 0x800>;
|
|
};
|
|
|
|
mscm_ir: interrupt-controller@40001800 {
|
|
compatible = "fsl,vf610-mscm-ir";
|
|
reg = <0x40001800 0x400>;
|
|
fsl,cpucfg = <&mscm_cpucfg>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
edma0: dma-controller@40018000 {
|
|
#dma-cells = <2>;
|
|
compatible = "fsl,vf610-edma";
|
|
reg = <0x40018000 0x2000>,
|
|
<0x40024000 0x1000>,
|
|
<0x40025000 0x1000>;
|
|
dma-channels = <32>;
|
|
interrupts = <8 IRQ_TYPE_LEVEL_HIGH>,
|
|
<9 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "edma-tx", "edma-err";
|
|
clock-names = "dmamux0", "dmamux1";
|
|
clocks = <&clks VF610_CLK_DMAMUX0>,
|
|
<&clks VF610_CLK_DMAMUX1>;
|
|
status = "disabled";
|
|
};
|
|
|
|
can0: flexcan@40020000 {
|
|
compatible = "fsl,vf610-flexcan";
|
|
reg = <0x40020000 0x4000>;
|
|
interrupts = <58 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_FLEXCAN0>,
|
|
<&clks VF610_CLK_FLEXCAN0>;
|
|
clock-names = "ipg", "per";
|
|
status = "disabled";
|
|
};
|
|
|
|
uart0: serial@40027000 {
|
|
compatible = "fsl,vf610-lpuart";
|
|
reg = <0x40027000 0x1000>;
|
|
interrupts = <61 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_UART0>;
|
|
clock-names = "ipg";
|
|
dmas = <&edma0 0 2>,
|
|
<&edma0 0 3>;
|
|
dma-names = "rx","tx";
|
|
status = "disabled";
|
|
};
|
|
|
|
uart1: serial@40028000 {
|
|
compatible = "fsl,vf610-lpuart";
|
|
reg = <0x40028000 0x1000>;
|
|
interrupts = <62 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_UART1>;
|
|
clock-names = "ipg";
|
|
dmas = <&edma0 0 4>,
|
|
<&edma0 0 5>;
|
|
dma-names = "rx","tx";
|
|
status = "disabled";
|
|
};
|
|
|
|
uart2: serial@40029000 {
|
|
compatible = "fsl,vf610-lpuart";
|
|
reg = <0x40029000 0x1000>;
|
|
interrupts = <63 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_UART2>;
|
|
clock-names = "ipg";
|
|
dmas = <&edma0 0 6>,
|
|
<&edma0 0 7>;
|
|
dma-names = "rx","tx";
|
|
status = "disabled";
|
|
};
|
|
|
|
uart3: serial@4002a000 {
|
|
compatible = "fsl,vf610-lpuart";
|
|
reg = <0x4002a000 0x1000>;
|
|
interrupts = <64 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_UART3>;
|
|
clock-names = "ipg";
|
|
dmas = <&edma0 0 8>,
|
|
<&edma0 0 9>;
|
|
dma-names = "rx","tx";
|
|
status = "disabled";
|
|
};
|
|
|
|
dspi0: dspi0@4002c000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-dspi";
|
|
reg = <0x4002c000 0x1000>;
|
|
interrupts = <67 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_DSPI0>;
|
|
clock-names = "dspi";
|
|
spi-num-chipselects = <5>;
|
|
status = "disabled";
|
|
};
|
|
|
|
dspi1: dspi1@4002d000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-dspi";
|
|
reg = <0x4002d000 0x1000>;
|
|
interrupts = <68 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_DSPI1>;
|
|
clock-names = "dspi";
|
|
spi-num-chipselects = <5>;
|
|
status = "disabled";
|
|
};
|
|
|
|
sai2: sai@40031000 {
|
|
compatible = "fsl,vf610-sai";
|
|
reg = <0x40031000 0x1000>;
|
|
interrupts = <86 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_SAI2>;
|
|
clock-names = "sai";
|
|
dma-names = "tx", "rx";
|
|
dmas = <&edma0 0 21>,
|
|
<&edma0 0 20>;
|
|
status = "disabled";
|
|
};
|
|
|
|
pit: pit@40037000 {
|
|
compatible = "fsl,vf610-pit";
|
|
reg = <0x40037000 0x1000>;
|
|
interrupts = <39 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_PIT>;
|
|
clock-names = "pit";
|
|
};
|
|
|
|
pwm0: pwm@40038000 {
|
|
compatible = "fsl,vf610-ftm-pwm";
|
|
#pwm-cells = <3>;
|
|
reg = <0x40038000 0x1000>;
|
|
clock-names = "ftm_sys", "ftm_ext",
|
|
"ftm_fix", "ftm_cnt_clk_en";
|
|
clocks = <&clks VF610_CLK_FTM0>,
|
|
<&clks VF610_CLK_FTM0_EXT_SEL>,
|
|
<&clks VF610_CLK_FTM0_FIX_SEL>,
|
|
<&clks VF610_CLK_FTM0_EXT_FIX_EN>;
|
|
status = "disabled";
|
|
};
|
|
|
|
pwm1: pwm@40039000 {
|
|
compatible = "fsl,vf610-ftm-pwm";
|
|
#pwm-cells = <3>;
|
|
reg = <0x40039000 0x1000>;
|
|
clock-names = "ftm_sys", "ftm_ext",
|
|
"ftm_fix", "ftm_cnt_clk_en";
|
|
clocks = <&clks VF610_CLK_FTM1>,
|
|
<&clks VF610_CLK_FTM1_EXT_SEL>,
|
|
<&clks VF610_CLK_FTM1_FIX_SEL>,
|
|
<&clks VF610_CLK_FTM1_EXT_FIX_EN>;
|
|
status = "disabled";
|
|
};
|
|
|
|
adc0: adc@4003b000 {
|
|
compatible = "fsl,vf610-adc";
|
|
reg = <0x4003b000 0x1000>;
|
|
interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_ADC0>;
|
|
clock-names = "adc";
|
|
#io-channel-cells = <1>;
|
|
status = "disabled";
|
|
fsl,adck-max-frequency = <30000000>, <40000000>,
|
|
<20000000>;
|
|
};
|
|
|
|
wdoga5: wdog@4003e000 {
|
|
compatible = "fsl,vf610-wdt", "fsl,imx21-wdt";
|
|
reg = <0x4003e000 0x1000>;
|
|
interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_WDT>;
|
|
clock-names = "wdog";
|
|
status = "disabled";
|
|
};
|
|
|
|
qspi0: quadspi@40044000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-qspi";
|
|
reg = <0x40044000 0x1000>, <0x20000000 0x10000000>;
|
|
reg-names = "QuadSPI", "QuadSPI-memory";
|
|
interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_QSPI0_EN>,
|
|
<&clks VF610_CLK_QSPI0>;
|
|
clock-names = "qspi_en", "qspi";
|
|
status = "disabled";
|
|
};
|
|
|
|
iomuxc: iomuxc@40048000 {
|
|
compatible = "fsl,vf610-iomuxc";
|
|
reg = <0x40048000 0x1000>;
|
|
};
|
|
|
|
gpio0: gpio@40049000 {
|
|
compatible = "fsl,vf610-gpio";
|
|
reg = <0x40049000 0x1000 0x400ff000 0x40>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-ranges = <&iomuxc 0 0 32>;
|
|
};
|
|
|
|
gpio1: gpio@4004a000 {
|
|
compatible = "fsl,vf610-gpio";
|
|
reg = <0x4004a000 0x1000 0x400ff040 0x40>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <108 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-ranges = <&iomuxc 0 32 32>;
|
|
};
|
|
|
|
gpio2: gpio@4004b000 {
|
|
compatible = "fsl,vf610-gpio";
|
|
reg = <0x4004b000 0x1000 0x400ff080 0x40>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <109 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-ranges = <&iomuxc 0 64 32>;
|
|
};
|
|
|
|
gpio3: gpio@4004c000 {
|
|
compatible = "fsl,vf610-gpio";
|
|
reg = <0x4004c000 0x1000 0x400ff0c0 0x40>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <110 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-ranges = <&iomuxc 0 96 32>;
|
|
};
|
|
|
|
gpio4: gpio@4004d000 {
|
|
compatible = "fsl,vf610-gpio";
|
|
reg = <0x4004d000 0x1000 0x400ff100 0x40>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <111 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-ranges = <&iomuxc 0 128 7>;
|
|
};
|
|
|
|
anatop: anatop@40050000 {
|
|
compatible = "fsl,vf610-anatop", "syscon";
|
|
reg = <0x40050000 0x400>;
|
|
};
|
|
|
|
usbphy0: usbphy@40050800 {
|
|
compatible = "fsl,vf610-usbphy";
|
|
reg = <0x40050800 0x400>;
|
|
interrupts = <50 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_USBPHY0>;
|
|
fsl,anatop = <&anatop>;
|
|
status = "disabled";
|
|
};
|
|
|
|
usbphy1: usbphy@40050c00 {
|
|
compatible = "fsl,vf610-usbphy";
|
|
reg = <0x40050c00 0x400>;
|
|
interrupts = <51 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_USBPHY1>;
|
|
fsl,anatop = <&anatop>;
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c0: i2c@40066000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-i2c";
|
|
reg = <0x40066000 0x1000>;
|
|
interrupts = <71 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_I2C0>;
|
|
clock-names = "ipg";
|
|
dmas = <&edma0 0 50>,
|
|
<&edma0 0 51>;
|
|
dma-names = "rx","tx";
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c1: i2c@40067000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-i2c";
|
|
reg = <0x40067000 0x1000>;
|
|
interrupts = <72 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_I2C1>;
|
|
clock-names = "ipg";
|
|
dmas = <&edma0 0 52>,
|
|
<&edma0 0 53>;
|
|
dma-names = "rx","tx";
|
|
status = "disabled";
|
|
};
|
|
|
|
clks: ccm@4006b000 {
|
|
compatible = "fsl,vf610-ccm";
|
|
reg = <0x4006b000 0x1000>;
|
|
clocks = <&sxosc>, <&fxosc>;
|
|
clock-names = "sxosc", "fxosc";
|
|
#clock-cells = <1>;
|
|
};
|
|
|
|
usbdev0: usb@40034000 {
|
|
compatible = "fsl,vf610-usb", "fsl,imx27-usb";
|
|
reg = <0x40034000 0x800>;
|
|
interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_USBC0>;
|
|
fsl,usbphy = <&usbphy0>;
|
|
fsl,usbmisc = <&usbmisc0 0>;
|
|
dr_mode = "peripheral";
|
|
status = "disabled";
|
|
};
|
|
|
|
usbmisc0: usb@40034800 {
|
|
#index-cells = <1>;
|
|
compatible = "fsl,vf610-usbmisc";
|
|
reg = <0x40034800 0x200>;
|
|
clocks = <&clks VF610_CLK_USBC0>;
|
|
status = "disabled";
|
|
};
|
|
|
|
src: src@4006e000 {
|
|
compatible = "fsl,vf610-src", "syscon";
|
|
reg = <0x4006e000 0x1000>;
|
|
interrupts = <96 IRQ_TYPE_LEVEL_HIGH>;
|
|
};
|
|
};
|
|
|
|
aips1: aips-bus@40080000 {
|
|
compatible = "fsl,aips-bus", "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
edma1: dma-controller@40098000 {
|
|
#dma-cells = <2>;
|
|
compatible = "fsl,vf610-edma";
|
|
reg = <0x40098000 0x2000>,
|
|
<0x400a1000 0x1000>,
|
|
<0x400a2000 0x1000>;
|
|
dma-channels = <32>;
|
|
interrupts = <10 IRQ_TYPE_LEVEL_HIGH>,
|
|
<11 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "edma-tx", "edma-err";
|
|
clock-names = "dmamux0", "dmamux1";
|
|
clocks = <&clks VF610_CLK_DMAMUX2>,
|
|
<&clks VF610_CLK_DMAMUX3>;
|
|
status = "disabled";
|
|
};
|
|
|
|
snvs0: snvs@400a7000 {
|
|
compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
|
|
reg = <0x400a7000 0x2000>;
|
|
|
|
snvsrtc: snvs-rtc-lp {
|
|
compatible = "fsl,sec-v4.0-mon-rtc-lp";
|
|
regmap = <&snvs0>;
|
|
offset = <0x34>;
|
|
interrupts = <100 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_SNVS>;
|
|
clock-names = "snvs-rtc";
|
|
};
|
|
};
|
|
|
|
uart4: serial@400a9000 {
|
|
compatible = "fsl,vf610-lpuart";
|
|
reg = <0x400a9000 0x1000>;
|
|
interrupts = <65 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_UART4>;
|
|
clock-names = "ipg";
|
|
status = "disabled";
|
|
};
|
|
|
|
uart5: serial@400aa000 {
|
|
compatible = "fsl,vf610-lpuart";
|
|
reg = <0x400aa000 0x1000>;
|
|
interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_UART5>;
|
|
clock-names = "ipg";
|
|
status = "disabled";
|
|
};
|
|
|
|
adc1: adc@400bb000 {
|
|
compatible = "fsl,vf610-adc";
|
|
reg = <0x400bb000 0x1000>;
|
|
interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_ADC1>;
|
|
clock-names = "adc";
|
|
#io-channel-cells = <1>;
|
|
status = "disabled";
|
|
};
|
|
|
|
esdhc0: esdhc@400b1000 {
|
|
compatible = "fsl,imx53-esdhc";
|
|
reg = <0x400b1000 0x1000>;
|
|
interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_IPG_BUS>,
|
|
<&clks VF610_CLK_PLATFORM_BUS>,
|
|
<&clks VF610_CLK_ESDHC0>;
|
|
clock-names = "ipg", "ahb", "per";
|
|
status = "disabled";
|
|
fsl,adck-max-frequency = <30000000>, <40000000>,
|
|
<20000000>;
|
|
};
|
|
|
|
esdhc1: esdhc@400b2000 {
|
|
compatible = "fsl,imx53-esdhc";
|
|
reg = <0x400b2000 0x1000>;
|
|
interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_IPG_BUS>,
|
|
<&clks VF610_CLK_PLATFORM_BUS>,
|
|
<&clks VF610_CLK_ESDHC1>;
|
|
clock-names = "ipg", "ahb", "per";
|
|
status = "disabled";
|
|
};
|
|
|
|
usbh1: usb@400b4000 {
|
|
compatible = "fsl,vf610-usb", "fsl,imx27-usb";
|
|
reg = <0x400b4000 0x800>;
|
|
interrupts = <76 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_USBC1>;
|
|
fsl,usbphy = <&usbphy1>;
|
|
fsl,usbmisc = <&usbmisc1 0>;
|
|
dr_mode = "host";
|
|
status = "disabled";
|
|
};
|
|
|
|
usbmisc1: usb@400b4800 {
|
|
#index-cells = <1>;
|
|
compatible = "fsl,vf610-usbmisc";
|
|
reg = <0x400b4800 0x200>;
|
|
clocks = <&clks VF610_CLK_USBC1>;
|
|
status = "disabled";
|
|
};
|
|
|
|
ftm: ftm@400b8000 {
|
|
compatible = "fsl,ftm-timer";
|
|
reg = <0x400b8000 0x1000 0x400b9000 0x1000>;
|
|
interrupts = <44 IRQ_TYPE_LEVEL_HIGH>;
|
|
clock-names = "ftm-evt", "ftm-src",
|
|
"ftm-evt-counter-en", "ftm-src-counter-en";
|
|
clocks = <&clks VF610_CLK_FTM2>,
|
|
<&clks VF610_CLK_FTM3>,
|
|
<&clks VF610_CLK_FTM2_EXT_FIX_EN>,
|
|
<&clks VF610_CLK_FTM3_EXT_FIX_EN>;
|
|
status = "disabled";
|
|
};
|
|
|
|
qspi1: quadspi@400c4000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-qspi";
|
|
reg = <0x400c4000 0x1000>, <0x50000000 0x10000000>;
|
|
reg-names = "QuadSPI", "QuadSPI-memory";
|
|
interrupts = <25 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_QSPI1_EN>,
|
|
<&clks VF610_CLK_QSPI1>;
|
|
clock-names = "qspi_en", "qspi";
|
|
status = "disabled";
|
|
};
|
|
|
|
fec0: ethernet@400d0000 {
|
|
compatible = "fsl,mvf600-fec";
|
|
reg = <0x400d0000 0x1000>;
|
|
interrupts = <78 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_ENET0>,
|
|
<&clks VF610_CLK_ENET0>,
|
|
<&clks VF610_CLK_ENET>;
|
|
clock-names = "ipg", "ahb", "ptp";
|
|
status = "disabled";
|
|
};
|
|
|
|
fec1: ethernet@400d1000 {
|
|
compatible = "fsl,mvf600-fec";
|
|
reg = <0x400d1000 0x1000>;
|
|
interrupts = <79 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_ENET1>,
|
|
<&clks VF610_CLK_ENET1>,
|
|
<&clks VF610_CLK_ENET>;
|
|
clock-names = "ipg", "ahb", "ptp";
|
|
status = "disabled";
|
|
};
|
|
|
|
can1: flexcan@400d4000 {
|
|
compatible = "fsl,vf610-flexcan";
|
|
reg = <0x400d4000 0x4000>;
|
|
interrupts = <59 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_FLEXCAN1>,
|
|
<&clks VF610_CLK_FLEXCAN1>;
|
|
clock-names = "ipg", "per";
|
|
status = "disabled";
|
|
};
|
|
|
|
nfc: nand@400e0000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-nfc";
|
|
reg = <0x400e0000 0x4000>;
|
|
interrupts = <83 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_NFC>;
|
|
clock-names = "nfc";
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c2: i2c@400e6000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-i2c";
|
|
reg = <0x400e6000 0x1000>;
|
|
interrupts = <73 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_I2C2>;
|
|
clock-names = "ipg";
|
|
dmas = <&edma0 1 36>,
|
|
<&edma0 1 37>;
|
|
dma-names = "rx","tx";
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c3: i2c@400e7000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,vf610-i2c";
|
|
reg = <0x400e7000 0x1000>;
|
|
interrupts = <74 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clks VF610_CLK_I2C3>;
|
|
clock-names = "ipg";
|
|
dmas = <&edma0 1 38>,
|
|
<&edma0 1 39>;
|
|
dma-names = "rx","tx";
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|
|
};
|