mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
aa61321d4c
The RFBI driver has not worked nor compiled for many years. There are very few boards out there that use RFBI, and no one has stepped up to fix it. So let's remove the RFBI code that doesn't even compile. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
127 lines
3.2 KiB
Plaintext
127 lines
3.2 KiB
Plaintext
config OMAP2_DSS_INIT
|
|
bool
|
|
|
|
config OMAP_DSS_BASE
|
|
tristate
|
|
|
|
menuconfig OMAP2_DSS
|
|
tristate "OMAP2+ Display Subsystem support"
|
|
select OMAP_DSS_BASE
|
|
select VIDEOMODE_HELPERS
|
|
select OMAP2_DSS_INIT
|
|
select HDMI
|
|
help
|
|
OMAP2+ Display Subsystem support.
|
|
|
|
if OMAP2_DSS
|
|
|
|
config OMAP2_DSS_DEBUG
|
|
bool "Debug support"
|
|
default n
|
|
help
|
|
This enables printing of debug messages. Alternatively, debug messages
|
|
can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting
|
|
appropriate flags in <debugfs>/dynamic_debug/control.
|
|
|
|
config OMAP2_DSS_DEBUGFS
|
|
bool "Debugfs filesystem support"
|
|
depends on DEBUG_FS
|
|
default n
|
|
help
|
|
This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables
|
|
querying about clock configuration and register configuration of dss,
|
|
dispc, dsi, hdmi and rfbi.
|
|
|
|
config OMAP2_DSS_COLLECT_IRQ_STATS
|
|
bool "Collect DSS IRQ statistics"
|
|
depends on OMAP2_DSS_DEBUGFS
|
|
default n
|
|
help
|
|
Collect DSS IRQ statistics, printable via debugfs.
|
|
|
|
The statistics can be found from
|
|
<debugfs>/omapdss/dispc_irq for DISPC interrupts, and
|
|
<debugfs>/omapdss/dsi_irq for DSI interrupts.
|
|
|
|
config OMAP2_DSS_DPI
|
|
bool "DPI support"
|
|
default y
|
|
help
|
|
DPI Interface. This is the Parallel Display Interface.
|
|
|
|
config OMAP2_DSS_VENC
|
|
bool "VENC support"
|
|
default y
|
|
help
|
|
OMAP Video Encoder support for S-Video and composite TV-out.
|
|
|
|
config OMAP2_DSS_HDMI_COMMON
|
|
bool
|
|
|
|
config OMAP4_DSS_HDMI
|
|
bool "HDMI support for OMAP4"
|
|
default y
|
|
select OMAP2_DSS_HDMI_COMMON
|
|
help
|
|
HDMI support for OMAP4 based SoCs.
|
|
|
|
config OMAP5_DSS_HDMI
|
|
bool "HDMI support for OMAP5"
|
|
default n
|
|
select OMAP2_DSS_HDMI_COMMON
|
|
help
|
|
HDMI Interface for OMAP5 and similar cores. This adds the High
|
|
Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI
|
|
specification.
|
|
|
|
config OMAP2_DSS_SDI
|
|
bool "SDI support"
|
|
default n
|
|
help
|
|
SDI (Serial Display Interface) support.
|
|
|
|
SDI is a high speed one-way display serial bus between the host
|
|
processor and a display.
|
|
|
|
config OMAP2_DSS_DSI
|
|
bool "DSI support"
|
|
default n
|
|
help
|
|
MIPI DSI (Display Serial Interface) support.
|
|
|
|
DSI is a high speed half-duplex serial interface between the host
|
|
processor and a peripheral, such as a display or a framebuffer chip.
|
|
|
|
See http://www.mipi.org/ for DSI specifications.
|
|
|
|
config OMAP2_DSS_MIN_FCK_PER_PCK
|
|
int "Minimum FCK/PCK ratio (for scaling)"
|
|
range 0 32
|
|
default 0
|
|
help
|
|
This can be used to adjust the minimum FCK/PCK ratio.
|
|
|
|
With this you can make sure that DISPC FCK is at least
|
|
n x PCK. Video plane scaling requires higher FCK than
|
|
normally.
|
|
|
|
If this is set to 0, there's no extra constraint on the
|
|
DISPC FCK. However, the FCK will at minimum be
|
|
2xPCK (if active matrix) or 3xPCK (if passive matrix).
|
|
|
|
Max FCK is 173MHz, so this doesn't work if your PCK
|
|
is very high.
|
|
|
|
config OMAP2_DSS_SLEEP_AFTER_VENC_RESET
|
|
bool "Sleep 20ms after VENC reset"
|
|
default y
|
|
help
|
|
There is a 20ms sleep after VENC reset which seemed to fix the
|
|
reset. The reason for the bug is unclear, and it's also unclear
|
|
on what platforms this happens.
|
|
|
|
This option enables the sleep, and is enabled by default. You can
|
|
disable the sleep if it doesn't cause problems on your platform.
|
|
|
|
endif
|