linux_dsm_epyc7002/sound/firewire/bebob/bebob_maudio.c
Takashi Sakamoto 9076c22ddd ALSA: bebob: Add support for M-Audio usual Firewire series
This commit allows this driver to support some models which M-Audio produces
with DM1000/DM1000E with usual firmware. They are:
 - Firewire 410
 - Firewire AudioPhile
 - Firewire Solo
 - Ozonic
 - NRV10
 - FirewireLightBridge

According to a person who worked in BridgeCo, some models are produced with
'Pre-BeBoB'. This means that these products were released before BeBoB was
officially produced, and later BeBoB specification was formed. So these models
have some quirks.

M-Audio usual firmware quirks:
 - Just after powering on, 'Firewire 410' waits to download firmware. This
   state is changed when receiving cue. Then bus reset is generated and the
   device is recognized as a different model with the uploaded firmware.
 - 'Firewire Audiophile' also waits to download firmware but its
   vendor id/model id is the same as the one after loading firmware.
 - The information of channel mapping for MIDI conformant data channel is
   invalid against BridgeCo specification.

This commit adds some codes for these quirks but don't support to upload
firmware.

This commit also adds specific operations to get metering information. The
metering information also includes status of clock synchronization if the model
supports to switch source of clock.

The specification of FirewireLightBridge is unknown. So in this time, normal
operations are applied for this model.

Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26 14:32:03 +02:00

181 lines
4.7 KiB
C

/*
* bebob_maudio.c - a part of driver for BeBoB based devices
*
* Copyright (c) 2013-2014 Takashi Sakamoto
*
* Licensed under the terms of the GNU General Public License, version 2.
*/
#include "./bebob.h"
/*
* Just powering on, Firewire 410/Audiophile wait to
* download firmware blob. To enable these devices, drivers should upload
* firmware blob and send a command to initialize configuration to factory
* settings when completing uploading. Then these devices generate bus reset
* and are recognized as new devices with the firmware.
*
* For streaming, both of output and input streams are needed for Firewire 410
* and Ozonic. The single stream is OK for the other devices even if the clock
* source is not SYT-Match (I note no devices use SYT-Match).
*
* Without streaming, the devices except for Firewire Audiophile can mix any
* input and output. For this reason, Audiophile cannot be used as standalone
* mixer.
*/
#define MAUDIO_SPECIFIC_ADDRESS 0xffc700000000
#define METER_OFFSET 0x00600000
/* some device has sync info after metering data */
#define METER_SIZE_FW410 76 /* with sync info */
#define METER_SIZE_AUDIOPHILE 60 /* with sync info */
#define METER_SIZE_SOLO 52 /* with sync info */
#define METER_SIZE_OZONIC 48
#define METER_SIZE_NRV10 80
/* labels for metering */
#define ANA_IN "Analog In"
#define ANA_OUT "Analog Out"
#define DIG_IN "Digital In"
#define SPDIF_IN "S/PDIF In"
#define ADAT_IN "ADAT In"
#define DIG_OUT "Digital Out"
#define SPDIF_OUT "S/PDIF Out"
#define ADAT_OUT "ADAT Out"
#define STRM_IN "Stream In"
#define AUX_OUT "Aux Out"
#define HP_OUT "HP Out"
/* for NRV */
#define UNKNOWN_METER "Unknown"
static inline int
get_meter(struct snd_bebob *bebob, void *buf, unsigned int size)
{
return snd_fw_transaction(bebob->unit, TCODE_READ_BLOCK_REQUEST,
MAUDIO_SPECIFIC_ADDRESS + METER_OFFSET,
buf, size, 0);
}
/* last 4 bytes are omitted because it's clock info. */
static char *const fw410_meter_labels[] = {
ANA_IN, DIG_IN,
ANA_OUT, ANA_OUT, ANA_OUT, ANA_OUT, DIG_OUT,
HP_OUT
};
static char *const audiophile_meter_labels[] = {
ANA_IN, DIG_IN,
ANA_OUT, ANA_OUT, DIG_OUT,
HP_OUT, AUX_OUT,
};
static char *const solo_meter_labels[] = {
ANA_IN, DIG_IN,
STRM_IN, STRM_IN,
ANA_OUT, DIG_OUT
};
/* no clock info */
static char *const ozonic_meter_labels[] = {
ANA_IN, ANA_IN,
STRM_IN, STRM_IN,
ANA_OUT, ANA_OUT
};
/* TODO: need testers. these positions are based on authour's assumption */
static char *const nrv10_meter_labels[] = {
ANA_IN, ANA_IN, ANA_IN, ANA_IN,
DIG_IN,
ANA_OUT, ANA_OUT, ANA_OUT, ANA_OUT,
DIG_IN
};
static int
normal_meter_get(struct snd_bebob *bebob, u32 *buf, unsigned int size)
{
struct snd_bebob_meter_spec *spec = bebob->spec->meter;
unsigned int c, channels;
int err;
channels = spec->num * 2;
if (size < channels * sizeof(u32))
return -EINVAL;
err = get_meter(bebob, (void *)buf, size);
if (err < 0)
goto end;
for (c = 0; c < channels; c++)
be32_to_cpus(&buf[c]);
/* swap stream channels because inverted */
if (spec->labels == solo_meter_labels) {
swap(buf[4], buf[6]);
swap(buf[5], buf[7]);
}
end:
return err;
}
/* Firewire 410 specification */
static struct snd_bebob_rate_spec usual_rate_spec = {
.get = &snd_bebob_stream_get_rate,
.set = &snd_bebob_stream_set_rate,
};
static struct snd_bebob_meter_spec fw410_meter_spec = {
.num = ARRAY_SIZE(fw410_meter_labels),
.labels = fw410_meter_labels,
.get = &normal_meter_get
};
struct snd_bebob_spec maudio_fw410_spec = {
.clock = NULL,
.rate = &usual_rate_spec,
.meter = &fw410_meter_spec
};
/* Firewire Audiophile specification */
static struct snd_bebob_meter_spec audiophile_meter_spec = {
.num = ARRAY_SIZE(audiophile_meter_labels),
.labels = audiophile_meter_labels,
.get = &normal_meter_get
};
struct snd_bebob_spec maudio_audiophile_spec = {
.clock = NULL,
.rate = &usual_rate_spec,
.meter = &audiophile_meter_spec
};
/* Firewire Solo specification */
static struct snd_bebob_meter_spec solo_meter_spec = {
.num = ARRAY_SIZE(solo_meter_labels),
.labels = solo_meter_labels,
.get = &normal_meter_get
};
struct snd_bebob_spec maudio_solo_spec = {
.clock = NULL,
.rate = &usual_rate_spec,
.meter = &solo_meter_spec
};
/* Ozonic specification */
static struct snd_bebob_meter_spec ozonic_meter_spec = {
.num = ARRAY_SIZE(ozonic_meter_labels),
.labels = ozonic_meter_labels,
.get = &normal_meter_get
};
struct snd_bebob_spec maudio_ozonic_spec = {
.clock = NULL,
.rate = &usual_rate_spec,
.meter = &ozonic_meter_spec
};
/* NRV10 specification */
static struct snd_bebob_meter_spec nrv10_meter_spec = {
.num = ARRAY_SIZE(nrv10_meter_labels),
.labels = nrv10_meter_labels,
.get = &normal_meter_get
};
struct snd_bebob_spec maudio_nrv10_spec = {
.clock = NULL,
.rate = &usual_rate_spec,
.meter = &nrv10_meter_spec
};