mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-22 01:16:57 +07:00
41f3df3498
These nodes should be named dsi-controller@* so fix it up. Cc: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
80 lines
2.2 KiB
Plaintext
80 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* Device Tree for the TVK1281618 R2 UIB
|
|
*/
|
|
|
|
#include "ste-href-tvk1281618.dtsi"
|
|
|
|
/ {
|
|
soc {
|
|
i2c@80128000 {
|
|
lsm303dlh@18 {
|
|
/* Accelerometer */
|
|
compatible = "st,lsm303dlh-accel";
|
|
st,drdy-int-pin = <1>;
|
|
drive-open-drain;
|
|
reg = <0x18>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_tvk_mode>;
|
|
/*
|
|
* These interrupts cannot be used: the other component
|
|
* ST-Micro L3D4200D gyro that is connected to the same lines
|
|
* cannot set its DRDY line to open drain, so it cannot be
|
|
* shared with other peripherals. The should be defined for
|
|
* the falling edge if they could be wired together.
|
|
*
|
|
* interrupts-extended =
|
|
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
|
|
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
|
|
*/
|
|
};
|
|
lsm303dlh@1e {
|
|
/* Magnetometer */
|
|
compatible = "st,lsm303dlh-magn";
|
|
reg = <0x1e>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
/*
|
|
* These interrupts cannot be used: the other component
|
|
* ST-Micro L3D4200D gyro that is connected to the same lines
|
|
* cannot set its DRDY line to open drain, so it cannot be
|
|
* shared with other peripherals. The should be defined for
|
|
* the falling edge if they could be wired together.
|
|
*
|
|
* interrupts-extended =
|
|
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
|
|
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
|
|
*/
|
|
};
|
|
lis331dl@1c {
|
|
/* Accelerometer */
|
|
compatible = "st,lis331dl-accel";
|
|
st,drdy-int-pin = <1>;
|
|
reg = <0x1c>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_tvk_mode>;
|
|
interrupt-parent = <&gpio2>;
|
|
/* INT2 would need to be open drain */
|
|
interrupts = <18 IRQ_TYPE_EDGE_RISING>,
|
|
<19 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
};
|
|
mcde@a0350000 {
|
|
status = "okay";
|
|
|
|
dsi-controller@a0351000 {
|
|
panel {
|
|
compatible = "samsung,s6d16d0";
|
|
reg = <0>;
|
|
vdd1-supply = <&ab8500_ldo_aux1_reg>;
|
|
reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|