mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-21 08:46:49 +07:00
56060b04c6
IRQ number was missing. Suggested-by: Radu Nicolae Pirea <pirea.radu@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
86 lines
2.9 KiB
Plaintext
86 lines
2.9 KiB
Plaintext
* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART)
|
|
|
|
Required properties for USART:
|
|
- compatible: Should be "atmel,<chip>-usart" or "atmel,<chip>-dbgu"
|
|
The compatible <chip> indicated will be the first SoC to support an
|
|
additional mode or an USART new feature.
|
|
For the dbgu UART, use "atmel,<chip>-dbgu", "atmel,<chip>-usart"
|
|
- reg: Should contain registers location and length
|
|
- interrupts: Should contain interrupt
|
|
- clock-names: tuple listing input clock names.
|
|
Required elements: "usart"
|
|
- clocks: phandles to input clocks.
|
|
|
|
Required properties for USART in SPI mode:
|
|
- #size-cells : Must be <0>
|
|
- #address-cells : Must be <1>
|
|
- cs-gpios: chipselects (internal cs not supported)
|
|
- atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
|
|
|
|
Optional properties in serial mode:
|
|
- atmel,use-dma-rx: use of PDC or DMA for receiving data
|
|
- atmel,use-dma-tx: use of PDC or DMA for transmitting data
|
|
- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
|
|
It will use specified PIO instead of the peripheral function pin for the USART feature.
|
|
If unsure, don't specify this property.
|
|
- add dma bindings for dma transfer:
|
|
- dmas: DMA specifier, consisting of a phandle to DMA controller node,
|
|
memory peripheral interface and USART DMA channel ID, FIFO configuration.
|
|
Refer to dma.txt and atmel-dma.txt for details.
|
|
- dma-names: "rx" for RX channel, "tx" for TX channel.
|
|
- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
|
|
capable USARTs.
|
|
- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
|
|
|
|
<chip> compatible description:
|
|
- at91rm9200: legacy USART support
|
|
- at91sam9260: generic USART implementation for SAM9 SoCs
|
|
|
|
Example:
|
|
- use PDC:
|
|
usart0: serial@fff8c000 {
|
|
compatible = "atmel,at91sam9260-usart";
|
|
reg = <0xfff8c000 0x4000>;
|
|
interrupts = <7>;
|
|
clocks = <&usart0_clk>;
|
|
clock-names = "usart";
|
|
atmel,use-dma-rx;
|
|
atmel,use-dma-tx;
|
|
rts-gpios = <&pioD 15 GPIO_ACTIVE_LOW>;
|
|
cts-gpios = <&pioD 16 GPIO_ACTIVE_LOW>;
|
|
dtr-gpios = <&pioD 17 GPIO_ACTIVE_LOW>;
|
|
dsr-gpios = <&pioD 18 GPIO_ACTIVE_LOW>;
|
|
dcd-gpios = <&pioD 20 GPIO_ACTIVE_LOW>;
|
|
rng-gpios = <&pioD 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
- use DMA:
|
|
usart0: serial@f001c000 {
|
|
compatible = "atmel,at91sam9260-usart";
|
|
reg = <0xf001c000 0x100>;
|
|
interrupts = <12 4 5>;
|
|
clocks = <&usart0_clk>;
|
|
clock-names = "usart";
|
|
atmel,use-dma-rx;
|
|
atmel,use-dma-tx;
|
|
dmas = <&dma0 2 0x3>,
|
|
<&dma0 2 0x204>;
|
|
dma-names = "tx", "rx";
|
|
atmel,fifo-size = <32>;
|
|
};
|
|
|
|
- SPI mode:
|
|
#include <dt-bindings/mfd/at91-usart.h>
|
|
|
|
spi0: spi@f001c000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "atmel,at91rm9200-usart", "atmel,at91sam9260-usart";
|
|
atmel,usart-mode = <AT91_USART_MODE_SPI>;
|
|
reg = <0xf001c000 0x100>;
|
|
interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
|
|
clocks = <&usart0_clk>;
|
|
clock-names = "usart";
|
|
cs-gpios = <&pioB 3 0>;
|
|
};
|