mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
c50495aa4c
This patch fixes a shared typo in several qcom pinctrl dt-bindings. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org>
97 lines
3.2 KiB
Plaintext
97 lines
3.2 KiB
Plaintext
Qualcomm MSM8660 TLMM block
|
|
|
|
Required properties:
|
|
- compatible: "qcom,msm8660-pinctrl"
|
|
- reg: Should be the base address and length of the TLMM block.
|
|
- interrupts: Should be the parent IRQ of the TLMM block.
|
|
- interrupt-controller: Marks the device node as an interrupt controller.
|
|
- #interrupt-cells: Should be two.
|
|
- gpio-controller: Marks the device node as a GPIO controller.
|
|
- #gpio-cells : Should be two.
|
|
The first cell is the gpio pin number and the
|
|
second cell is used for optional parameters.
|
|
- gpio-ranges: see ../gpio/gpio.txt
|
|
|
|
Optional properties:
|
|
|
|
- gpio-reserved-ranges: see ../gpio/gpio.txt
|
|
|
|
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
|
|
a general description of GPIO and interrupt bindings.
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices, including the meaning of the
|
|
phrase "pin configuration node".
|
|
|
|
Qualcomm's pin configuration nodes act as a container for an arbitrary number of
|
|
subnodes. Each of these subnodes represents some desired configuration for a
|
|
pin, a group, or a list of pins or groups. This configuration can include the
|
|
mux function to select on those pin(s)/group(s), and various pin configuration
|
|
parameters, such as pull-up, drive strength, etc.
|
|
|
|
The name of each subnode is not important; all subnodes should be enumerated
|
|
and processed purely based on their content.
|
|
|
|
Each subnode only affects those parameters that are explicitly listed. In
|
|
other words, a subnode that lists a mux function but no pin configuration
|
|
parameters implies no information about any pin configuration parameters.
|
|
Similarly, a pin subnode that describes a pullup parameter implies no
|
|
information about e.g. the mux function.
|
|
|
|
|
|
The following generic properties as defined in pinctrl-bindings.txt are valid
|
|
to specify in a pin configuration subnode:
|
|
|
|
pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-strength,
|
|
output-low, output-high.
|
|
|
|
Non-empty subnodes must specify the 'pins' property.
|
|
|
|
Valid values for pins are:
|
|
gpio0-gpio172, sdc3_clk, sdc3_cmd, sdc3_data sdc4_clk, sdc4_cmd, sdc4_data
|
|
|
|
Valid values for function are:
|
|
gpio, cam_mclk, dsub, ext_gps, gp_clk_0a, gp_clk_0b, gp_clk_1a, gp_clk_1b,
|
|
gp_clk_2a, gp_clk_2b, gp_mn, gsbi1, gsbi1_spi_cs1_n, gsbi1_spi_cs2a_n,
|
|
gsbi1_spi_cs2b_n, gsbi1_spi_cs3_n, gsbi2, gsbi2_spi_cs1_n, gsbi2_spi_cs2_n,
|
|
gsbi2_spi_cs3_n, gsbi3, gsbi3_spi_cs1_n, gsbi3_spi_cs2_n, gsbi3_spi_cs3_n,
|
|
gsbi4, gsbi5, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10, gsbi11, gsbi12, hdmi, i2s,
|
|
lcdc, mdp_vsync, mi2s, pcm, ps_hold, sdc1, sdc2, sdc5, tsif1, tsif2, usb_fs1,
|
|
usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, ebi2, ebi2cs
|
|
|
|
Example:
|
|
|
|
msmgpio: pinctrl@800000 {
|
|
compatible = "qcom,msm8660-pinctrl";
|
|
reg = <0x800000 0x4000>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-ranges = <&msmgpio 0 0 173>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <0 16 0x4>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gsbi12_uart>;
|
|
|
|
gsbi12_uart: gsbi12-uart {
|
|
mux {
|
|
pins = "gpio117", "gpio118";
|
|
function = "gsbi12";
|
|
};
|
|
|
|
tx {
|
|
pins = "gpio118";
|
|
drive-strength = <8>;
|
|
bias-disable;
|
|
};
|
|
|
|
rx {
|
|
pins = "gpio117";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
};
|