mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
95d2f00657
Add devicetree bindings for Mediatek MT6797 SoC Pin Controller. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
84 lines
3.5 KiB
Plaintext
84 lines
3.5 KiB
Plaintext
* MediaTek MT6797 Pin Controller
|
|
|
|
The MediaTek's MT6797 Pin controller is used to control SoC pins.
|
|
|
|
Required properties:
|
|
- compatible: Value should be one of the following.
|
|
"mediatek,mt6797-pinctrl", compatible with mt6797 pinctrl.
|
|
- reg: Should contain address and size for gpio, iocfgl, iocfgb,
|
|
iocfgr and iocfgt register bases.
|
|
- reg-names: An array of strings describing the "reg" entries. Must
|
|
contain "gpio", "iocfgl", "iocfgb", "iocfgr", "iocfgt".
|
|
- gpio-controller: Marks the device node as a gpio controller.
|
|
- #gpio-cells: Should be two. The first cell is the gpio pin number
|
|
and the second cell is used for optional parameters.
|
|
|
|
Optional properties:
|
|
- interrupt-controller: Marks the device node as an interrupt controller.
|
|
- #interrupt-cells: Should be two.
|
|
- interrupts : The interrupt outputs from the controller.
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices.
|
|
|
|
Subnode format
|
|
A pinctrl node should contain at least one subnodes representing the
|
|
pinctrl groups available on the machine. Each subnode will list the
|
|
pins it needs, and how they should be configured, with regard to muxer
|
|
configuration, pullups, drive strength, input enable/disable and input schmitt.
|
|
|
|
node {
|
|
pinmux = <PIN_NUMBER_PINMUX>;
|
|
GENERIC_PINCONFIG;
|
|
};
|
|
|
|
Required properties:
|
|
- pinmux: Integer array, represents gpio pin number and mux setting.
|
|
Supported pin number and mux varies for different SoCs, and are defined
|
|
as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly.
|
|
|
|
Optional properties:
|
|
- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
|
|
bias-pull, bias-pull-down, input-enable, input-schmitt-enable,
|
|
input-schmitt-disable, output-enable output-low, output-high,
|
|
drive-strength, and slew-rate are valid.
|
|
|
|
Valid arguments for 'slew-rate' are '0' for no slew rate controlled and
|
|
'1' for slower slew rate respectively. Valid arguments for 'drive-strength'
|
|
is limited, such as 2, 4, 8, 12, or 16 in mA.
|
|
|
|
Some optional vendor properties as defined are valid to specify in a
|
|
pinconf subnode:
|
|
- mediatek,tdsel: An integer describing the steps for output level shifter
|
|
duty cycle when asserted (high pulse width adjustment). Valid arguments
|
|
are from 0 to 15.
|
|
- mediatek,rdsel: An integer describing the steps for input level shifter
|
|
duty cycle when asserted (high pulse width adjustment). Valid arguments
|
|
are from 0 to 63.
|
|
- mediatek,pull-up-adv: An integer describing the code R1R0 as 0, 1, 2
|
|
or 3 for the advanced pull-up resistors.
|
|
- mediatek,pull-down-adv: An integer describing the code R1R0 as 0, 1, 2,
|
|
or 3 for the advanced pull-down resistors.
|
|
|
|
Examples:
|
|
|
|
pio: pinctrl@10005000 {
|
|
compatible = "mediatek,mt6797-pinctrl";
|
|
reg = <0 0x10005000 0 0x1000>,
|
|
<0 0x10002000 0 0x400>,
|
|
<0 0x10002400 0 0x400>,
|
|
<0 0x10002800 0 0x400>,
|
|
<0 0x10002C00 0 0x400>;
|
|
reg-names = "gpio", "iocfgl", "iocfgb",
|
|
"iocfgr", "iocfgt";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
uart1_pins_a: uart1 {
|
|
pins1 {
|
|
pinmux = <MT6797_GPIO232__FUNC_URXD1>,
|
|
<MT6797_GPIO233__FUNC_UTXD1>;
|
|
};
|
|
};
|
|
};
|