mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-26 08:25:01 +07:00
4f73bc4dd3
The option allows you to remove TTY and compile without errors. This saves space on systems that won't support TTY interfaces anyway. bloat-o-meter output is below. The bulk of this patch consists of Kconfig changes adding "depends on TTY" to various serial devices and similar drivers that require the TTY layer. Ideally, these dependencies would occur on a common intermediate symbol such as SERIO, but most drivers "select SERIO" rather than "depends on SERIO", and "select" does not respect dependencies. bloat-o-meter output comparing our previous minimal to new minimal by removing TTY. The list is filtered to not show removed entries with awk '$3 != "-"' as the list was very long. add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350) function old new delta chr_dev_init 166 170 +4 allow_signal 80 82 +2 static.__warned 143 142 -1 disallow_signal 63 62 -1 __set_special_pids 95 94 -1 unregister_console 126 121 -5 start_kernel 546 541 -5 register_console 593 588 -5 copy_from_user 45 40 -5 sys_setsid 128 120 -8 sys_vhangup 32 19 -13 do_exit 1543 1526 -17 bitmap_zero 60 40 -20 arch_local_irq_save 137 117 -20 release_task 674 652 -22 static.spin_unlock_irqrestore 308 260 -48 Signed-off-by: Joe Millenbach <jmillenbach@gmail.com> Reviewed-by: Jamey Sharp <jamey@minilop.net> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
71 lines
2.1 KiB
Plaintext
71 lines
2.1 KiB
Plaintext
#
|
|
# MMC/SD card drivers
|
|
#
|
|
|
|
comment "MMC/SD/SDIO Card Drivers"
|
|
|
|
config MMC_BLOCK
|
|
tristate "MMC block device driver"
|
|
depends on BLOCK
|
|
default y
|
|
help
|
|
Say Y here to enable the MMC block device driver support.
|
|
This provides a block device driver, which you can use to
|
|
mount the filesystem. Almost everyone wishing MMC support
|
|
should say Y or M here.
|
|
|
|
config MMC_BLOCK_MINORS
|
|
int "Number of minors per block device"
|
|
depends on MMC_BLOCK
|
|
range 4 256
|
|
default 8
|
|
help
|
|
Number of minors per block device. One is needed for every
|
|
partition on the disk (plus one for the whole disk).
|
|
|
|
Number of total MMC minors available is 256, so your number
|
|
of supported block devices will be limited to 256 divided
|
|
by this number.
|
|
|
|
Default is 8 to be backwards compatible with previous
|
|
hardwired device numbering.
|
|
|
|
If unsure, say 8 here.
|
|
|
|
config MMC_BLOCK_BOUNCE
|
|
bool "Use bounce buffer for simple hosts"
|
|
depends on MMC_BLOCK
|
|
default y
|
|
help
|
|
SD/MMC is a high latency protocol where it is crucial to
|
|
send large requests in order to get high performance. Many
|
|
controllers, however, are restricted to continuous memory
|
|
(i.e. they can't do scatter-gather), something the kernel
|
|
rarely can provide.
|
|
|
|
Say Y here to help these restricted hosts by bouncing
|
|
requests back and forth from a large buffer. You will get
|
|
a big performance gain at the cost of up to 64 KiB of
|
|
physical memory.
|
|
|
|
If unsure, say Y here.
|
|
|
|
config SDIO_UART
|
|
tristate "SDIO UART/GPS class support"
|
|
depends on TTY
|
|
help
|
|
SDIO function driver for SDIO cards that implements the UART
|
|
class, as well as the GPS class which appears like a UART.
|
|
|
|
config MMC_TEST
|
|
tristate "MMC host test driver"
|
|
help
|
|
Development driver that performs a series of reads and writes
|
|
to a memory card in order to expose certain well known bugs
|
|
in host controllers. The tests are executed by writing to the
|
|
"test" file in debugfs under each card. Note that whatever is
|
|
on your card will be overwritten by these tests.
|
|
|
|
This driver is only of interest to those developing or
|
|
testing a host driver. Most people should say N here.
|