AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-24 00:10:10 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
7d14ecd050
linux_dsm_epyc7002/drivers/mtd/nand/omap2.c
Ezequiel García fef775caa7 nand: omap2: Add support for flash-based bad block table 
This commit adds a new platform-data boolean property that enables use
of a flash-based bad block table. This can also be enabled by setting
the 'nand-on-flash-bbt' devicetree property.

If the flash BBT is not enabled, the driver falls back to use OOB
bad block markers only, as before. If the flash BBT is enabled the
kernel will keep track of bad blocks using a BBT, in addition to
the OOB markers.

As explained by Brian Norris the reasons for using a BBT are:

""
The primary reason would be that NAND datasheets specify it these days.
A better argument is that nobody guarantees that you can write a
bad block marker to a worn out block; you may just get program failures.

This has been acknowledged by several developers over the last several
years.

Additionally, you get a boot-time performance improvement if you only
have to read a few pages, instead of a page or two from every block on
the flash.
""

Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-09-17 01:02:48 -07:00

2091 lines
59 KiB
C
Raw Blame History

/*
* Copyright © 2004 Texas Instruments, Jian Zhang <jzhang@ti.com>
* Copyright © 2004 Micron Technology Inc.
* Copyright © 2004 David Brownell
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/platform_device.h>
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/jiffies.h>
#include <linux/sched.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/omap-dma.h>
#include <linux/io.h>
#include <linux/slab.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/mtd/nand_bch.h>
#include <linux/platform_data/elm.h>
#include <linux/platform_data/mtd-nand-omap2.h>
#define DRIVER_NAME "omap2-nand"
#define OMAP_NAND_TIMEOUT_MS 5000
#define NAND_Ecc_P1e (1 << 0)
#define NAND_Ecc_P2e (1 << 1)
#define NAND_Ecc_P4e (1 << 2)
#define NAND_Ecc_P8e (1 << 3)
#define NAND_Ecc_P16e (1 << 4)
#define NAND_Ecc_P32e (1 << 5)
#define NAND_Ecc_P64e (1 << 6)
#define NAND_Ecc_P128e (1 << 7)
#define NAND_Ecc_P256e (1 << 8)
#define NAND_Ecc_P512e (1 << 9)
#define NAND_Ecc_P1024e (1 << 10)
#define NAND_Ecc_P2048e (1 << 11)
#define NAND_Ecc_P1o (1 << 16)
#define NAND_Ecc_P2o (1 << 17)
#define NAND_Ecc_P4o (1 << 18)
#define NAND_Ecc_P8o (1 << 19)
#define NAND_Ecc_P16o (1 << 20)
#define NAND_Ecc_P32o (1 << 21)
#define NAND_Ecc_P64o (1 << 22)
#define NAND_Ecc_P128o (1 << 23)
#define NAND_Ecc_P256o (1 << 24)
#define NAND_Ecc_P512o (1 << 25)
#define NAND_Ecc_P1024o (1 << 26)
#define NAND_Ecc_P2048o (1 << 27)
#define TF(value) (value ? 1 : 0)
#define P2048e(a) (TF(a & NAND_Ecc_P2048e) << 0)
#define P2048o(a) (TF(a & NAND_Ecc_P2048o) << 1)
#define P1e(a) (TF(a & NAND_Ecc_P1e) << 2)
#define P1o(a) (TF(a & NAND_Ecc_P1o) << 3)
#define P2e(a) (TF(a & NAND_Ecc_P2e) << 4)
#define P2o(a) (TF(a & NAND_Ecc_P2o) << 5)
#define P4e(a) (TF(a & NAND_Ecc_P4e) << 6)
#define P4o(a) (TF(a & NAND_Ecc_P4o) << 7)
#define P8e(a) (TF(a & NAND_Ecc_P8e) << 0)
#define P8o(a) (TF(a & NAND_Ecc_P8o) << 1)
#define P16e(a) (TF(a & NAND_Ecc_P16e) << 2)
#define P16o(a) (TF(a & NAND_Ecc_P16o) << 3)
#define P32e(a) (TF(a & NAND_Ecc_P32e) << 4)
#define P32o(a) (TF(a & NAND_Ecc_P32o) << 5)
#define P64e(a) (TF(a & NAND_Ecc_P64e) << 6)
#define P64o(a) (TF(a & NAND_Ecc_P64o) << 7)
#define P128e(a) (TF(a & NAND_Ecc_P128e) << 0)
#define P128o(a) (TF(a & NAND_Ecc_P128o) << 1)
#define P256e(a) (TF(a & NAND_Ecc_P256e) << 2)
#define P256o(a) (TF(a & NAND_Ecc_P256o) << 3)
#define P512e(a) (TF(a & NAND_Ecc_P512e) << 4)
#define P512o(a) (TF(a & NAND_Ecc_P512o) << 5)
#define P1024e(a) (TF(a & NAND_Ecc_P1024e) << 6)
#define P1024o(a) (TF(a & NAND_Ecc_P1024o) << 7)
#define P8e_s(a) (TF(a & NAND_Ecc_P8e) << 0)
#define P8o_s(a) (TF(a & NAND_Ecc_P8o) << 1)
#define P16e_s(a) (TF(a & NAND_Ecc_P16e) << 2)
#define P16o_s(a) (TF(a & NAND_Ecc_P16o) << 3)
#define P1e_s(a) (TF(a & NAND_Ecc_P1e) << 4)
#define P1o_s(a) (TF(a & NAND_Ecc_P1o) << 5)
#define P2e_s(a) (TF(a & NAND_Ecc_P2e) << 6)
#define P2o_s(a) (TF(a & NAND_Ecc_P2o) << 7)
#define P4e_s(a) (TF(a & NAND_Ecc_P4e) << 0)
#define P4o_s(a) (TF(a & NAND_Ecc_P4o) << 1)
#define PREFETCH_CONFIG1_CS_SHIFT 24
#define ECC_CONFIG_CS_SHIFT 1
#define CS_MASK 0x7
#define ENABLE_PREFETCH (0x1 << 7)
#define DMA_MPU_MODE_SHIFT 2
#define ECCSIZE0_SHIFT 12
#define ECCSIZE1_SHIFT 22
#define ECC1RESULTSIZE 0x1
#define ECCCLEAR 0x100
#define ECC1 0x1
#define PREFETCH_FIFOTHRESHOLD_MAX 0x40
#define PREFETCH_FIFOTHRESHOLD(val) ((val) << 8)
#define PREFETCH_STATUS_COUNT(val) (val & 0x00003fff)
#define PREFETCH_STATUS_FIFO_CNT(val) ((val >> 24) & 0x7F)
#define STATUS_BUFF_EMPTY 0x00000001
#define OMAP24XX_DMA_GPMC 4
#define SECTOR_BYTES 512
/* 4 bit padding to make byte aligned, 56 = 52 + 4 */
#define BCH4_BIT_PAD 4
/* GPMC ecc engine settings for read */
#define BCH_WRAPMODE_1 1 /* BCH wrap mode 1 */
#define BCH8R_ECC_SIZE0 0x1a /* ecc_size0 = 26 */
#define BCH8R_ECC_SIZE1 0x2 /* ecc_size1 = 2 */
#define BCH4R_ECC_SIZE0 0xd /* ecc_size0 = 13 */
#define BCH4R_ECC_SIZE1 0x3 /* ecc_size1 = 3 */
/* GPMC ecc engine settings for write */
#define BCH_WRAPMODE_6 6 /* BCH wrap mode 6 */
#define BCH_ECC_SIZE0 0x0 /* ecc_size0 = 0, no oob protection */
#define BCH_ECC_SIZE1 0x20 /* ecc_size1 = 32 */
#define BADBLOCK_MARKER_LENGTH 2
#ifdef CONFIG_MTD_NAND_OMAP_BCH
static u_char bch16_vector[] = {0xf5, 0x24, 0x1c, 0xd0, 0x61, 0xb3, 0xf1, 0x55,
0x2e, 0x2c, 0x86, 0xa3, 0xed, 0x36, 0x1b, 0x78,
0x48, 0x76, 0xa9, 0x3b, 0x97, 0xd1, 0x7a, 0x93,
0x07, 0x0e};
static u_char bch8_vector[] = {0xf3, 0xdb, 0x14, 0x16, 0x8b, 0xd2, 0xbe, 0xcc,
0xac, 0x6b, 0xff, 0x99, 0x7b};
static u_char bch4_vector[] = {0x00, 0x6b, 0x31, 0xdd, 0x41, 0xbc, 0x10};
#endif
/* oob info generated runtime depending on ecc algorithm and layout selected */
static struct nand_ecclayout omap_oobinfo;
struct omap_nand_info {
struct nand_hw_control controller;
struct omap_nand_platform_data *pdata;
struct mtd_info mtd;
struct nand_chip nand;
struct platform_device *pdev;
int gpmc_cs;
unsigned long phys_base;
enum omap_ecc ecc_opt;
struct completion comp;
struct dma_chan *dma;
int gpmc_irq_fifo;
int gpmc_irq_count;
enum {
OMAP_NAND_IO_READ = 0, /* read */
OMAP_NAND_IO_WRITE, /* write */
} iomode;
u_char *buf;
int buf_len;
struct gpmc_nand_regs reg;
/* fields specific for BCHx_HW ECC scheme */
struct device *elm_dev;
struct device_node *of_node;
};
/**
* omap_prefetch_enable - configures and starts prefetch transfer
* @cs: cs (chip select) number
* @fifo_th: fifo threshold to be used for read/ write
* @dma_mode: dma mode enable (1) or disable (0)
* @u32_count: number of bytes to be transferred
* @is_write: prefetch read(0) or write post(1) mode
*/
static int omap_prefetch_enable(int cs, int fifo_th, int dma_mode,
unsigned int u32_count, int is_write, struct omap_nand_info *info)
{
u32 val;
if (fifo_th > PREFETCH_FIFOTHRESHOLD_MAX)
return -1;
if (readl(info->reg.gpmc_prefetch_control))
return -EBUSY;
/* Set the amount of bytes to be prefetched */
writel(u32_count, info->reg.gpmc_prefetch_config2);
/* Set dma/mpu mode, the prefetch read / post write and
* enable the engine. Set which cs is has requested for.
*/
val = ((cs << PREFETCH_CONFIG1_CS_SHIFT) |
PREFETCH_FIFOTHRESHOLD(fifo_th) | ENABLE_PREFETCH |
(dma_mode << DMA_MPU_MODE_SHIFT) | (0x1 & is_write));
writel(val, info->reg.gpmc_prefetch_config1);
/* Start the prefetch engine */
writel(0x1, info->reg.gpmc_prefetch_control);
return 0;
}
/**
* omap_prefetch_reset - disables and stops the prefetch engine
*/
static int omap_prefetch_reset(int cs, struct omap_nand_info *info)
{
u32 config1;
/* check if the same module/cs is trying to reset */
config1 = readl(info->reg.gpmc_prefetch_config1);
if (((config1 >> PREFETCH_CONFIG1_CS_SHIFT) & CS_MASK) != cs)
return -EINVAL;
/* Stop the PFPW engine */
writel(0x0, info->reg.gpmc_prefetch_control);
/* Reset/disable the PFPW engine */
writel(0x0, info->reg.gpmc_prefetch_config1);
return 0;
}
/**
* omap_hwcontrol - hardware specific access to control-lines
* @mtd: MTD device structure
* @cmd: command to device
* @ctrl:
* NAND_NCE: bit 0 -> don't care
* NAND_CLE: bit 1 -> Command Latch
* NAND_ALE: bit 2 -> Address Latch
*
* NOTE: boards may use different bits for these!!
*/
static void omap_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
if (cmd != NAND_CMD_NONE) {
if (ctrl & NAND_CLE)
writeb(cmd, info->reg.gpmc_nand_command);
else if (ctrl & NAND_ALE)
writeb(cmd, info->reg.gpmc_nand_address);
else /* NAND_NCE */
writeb(cmd, info->reg.gpmc_nand_data);
}
}
/**
* omap_read_buf8 - read data from NAND controller into buffer
* @mtd: MTD device structure
* @buf: buffer to store date
* @len: number of bytes to read
*/
static void omap_read_buf8(struct mtd_info *mtd, u_char *buf, int len)
{
struct nand_chip *nand = mtd->priv;
ioread8_rep(nand->IO_ADDR_R, buf, len);
}
/**
* omap_write_buf8 - write buffer to NAND controller
* @mtd: MTD device structure
* @buf: data buffer
* @len: number of bytes to write
*/
static void omap_write_buf8(struct mtd_info *mtd, const u_char *buf, int len)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
u_char *p = (u_char *)buf;
u32 status = 0;
while (len--) {
iowrite8(*p++, info->nand.IO_ADDR_W);
/* wait until buffer is available for write */
do {
status = readl(info->reg.gpmc_status) &
STATUS_BUFF_EMPTY;
} while (!status);
}
}
/**
* omap_read_buf16 - read data from NAND controller into buffer
* @mtd: MTD device structure
* @buf: buffer to store date
* @len: number of bytes to read
*/
static void omap_read_buf16(struct mtd_info *mtd, u_char *buf, int len)
{
struct nand_chip *nand = mtd->priv;
ioread16_rep(nand->IO_ADDR_R, buf, len / 2);
}
/**
* omap_write_buf16 - write buffer to NAND controller
* @mtd: MTD device structure
* @buf: data buffer
* @len: number of bytes to write
*/
static void omap_write_buf16(struct mtd_info *mtd, const u_char * buf, int len)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
u16 *p = (u16 *) buf;
u32 status = 0;
/* FIXME try bursts of writesw() or DMA ... */
len >>= 1;
while (len--) {
iowrite16(*p++, info->nand.IO_ADDR_W);
/* wait until buffer is available for write */
do {
status = readl(info->reg.gpmc_status) &
STATUS_BUFF_EMPTY;
} while (!status);
}
}
/**
* omap_read_buf_pref - read data from NAND controller into buffer
* @mtd: MTD device structure
* @buf: buffer to store date
* @len: number of bytes to read
*/
static void omap_read_buf_pref(struct mtd_info *mtd, u_char *buf, int len)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
uint32_t r_count = 0;
int ret = 0;
u32 *p = (u32 *)buf;
/* take care of subpage reads */
if (len % 4) {
if (info->nand.options & NAND_BUSWIDTH_16)
omap_read_buf16(mtd, buf, len % 4);
else
omap_read_buf8(mtd, buf, len % 4);
p = (u32 *) (buf + len % 4);
len -= len % 4;
}
/* configure and start prefetch transfer */
ret = omap_prefetch_enable(info->gpmc_cs,
PREFETCH_FIFOTHRESHOLD_MAX, 0x0, len, 0x0, info);
if (ret) {
/* PFPW engine is busy, use cpu copy method */
if (info->nand.options & NAND_BUSWIDTH_16)
omap_read_buf16(mtd, (u_char *)p, len);
else
omap_read_buf8(mtd, (u_char *)p, len);
} else {
do {
r_count = readl(info->reg.gpmc_prefetch_status);
r_count = PREFETCH_STATUS_FIFO_CNT(r_count);
r_count = r_count >> 2;
ioread32_rep(info->nand.IO_ADDR_R, p, r_count);
p += r_count;
len -= r_count << 2;
} while (len);
/* disable and stop the PFPW engine */
omap_prefetch_reset(info->gpmc_cs, info);
}
}
/**
* omap_write_buf_pref - write buffer to NAND controller
* @mtd: MTD device structure
* @buf: data buffer
* @len: number of bytes to write
*/
static void omap_write_buf_pref(struct mtd_info *mtd,
const u_char *buf, int len)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
uint32_t w_count = 0;
int i = 0, ret = 0;
u16 *p = (u16 *)buf;
unsigned long tim, limit;
u32 val;
/* take care of subpage writes */
if (len % 2 != 0) {
writeb(*buf, info->nand.IO_ADDR_W);
p = (u16 *)(buf + 1);
len--;
}
/* configure and start prefetch transfer */
ret = omap_prefetch_enable(info->gpmc_cs,
PREFETCH_FIFOTHRESHOLD_MAX, 0x0, len, 0x1, info);
if (ret) {
/* PFPW engine is busy, use cpu copy method */
if (info->nand.options & NAND_BUSWIDTH_16)
omap_write_buf16(mtd, (u_char *)p, len);
else
omap_write_buf8(mtd, (u_char *)p, len);
} else {
while (len) {
w_count = readl(info->reg.gpmc_prefetch_status);
w_count = PREFETCH_STATUS_FIFO_CNT(w_count);
w_count = w_count >> 1;
for (i = 0; (i < w_count) && len; i++, len -= 2)
iowrite16(*p++, info->nand.IO_ADDR_W);
}
/* wait for data to flushed-out before reset the prefetch */
tim = 0;
limit = (loops_per_jiffy *
msecs_to_jiffies(OMAP_NAND_TIMEOUT_MS));
do {
cpu_relax();
val = readl(info->reg.gpmc_prefetch_status);
val = PREFETCH_STATUS_COUNT(val);
} while (val && (tim++ < limit));
/* disable and stop the PFPW engine */
omap_prefetch_reset(info->gpmc_cs, info);
}
}
/*
* omap_nand_dma_callback: callback on the completion of dma transfer
* @data: pointer to completion data structure
*/
static void omap_nand_dma_callback(void *data)
{
complete((struct completion *) data);
}
/*
* omap_nand_dma_transfer: configure and start dma transfer
* @mtd: MTD device structure
* @addr: virtual address in RAM of source/destination
* @len: number of data bytes to be transferred
* @is_write: flag for read/write operation
*/
static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr,
unsigned int len, int is_write)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
struct dma_async_tx_descriptor *tx;
enum dma_data_direction dir = is_write ? DMA_TO_DEVICE :
DMA_FROM_DEVICE;
struct scatterlist sg;
unsigned long tim, limit;
unsigned n;
int ret;
u32 val;
if (addr >= high_memory) {
struct page *p1;
if (((size_t)addr & PAGE_MASK) !=
((size_t)(addr + len - 1) & PAGE_MASK))
goto out_copy;
p1 = vmalloc_to_page(addr);
if (!p1)
goto out_copy;
addr = page_address(p1) + ((size_t)addr & ~PAGE_MASK);
}
sg_init_one(&sg, addr, len);
n = dma_map_sg(info->dma->device->dev, &sg, 1, dir);
if (n == 0) {
dev_err(&info->pdev->dev,
"Couldn't DMA map a %d byte buffer\n", len);
goto out_copy;
}
tx = dmaengine_prep_slave_sg(info->dma, &sg, n,
is_write ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!tx)
goto out_copy_unmap;
tx->callback = omap_nand_dma_callback;
tx->callback_param = &info->comp;
dmaengine_submit(tx);
/* configure and start prefetch transfer */
ret = omap_prefetch_enable(info->gpmc_cs,
PREFETCH_FIFOTHRESHOLD_MAX, 0x1, len, is_write, info);
if (ret)
/* PFPW engine is busy, use cpu copy method */
goto out_copy_unmap;
init_completion(&info->comp);
dma_async_issue_pending(info->dma);
/* setup and start DMA using dma_addr */
wait_for_completion(&info->comp);
tim = 0;
limit = (loops_per_jiffy * msecs_to_jiffies(OMAP_NAND_TIMEOUT_MS));
do {
cpu_relax();
val = readl(info->reg.gpmc_prefetch_status);
val = PREFETCH_STATUS_COUNT(val);
} while (val && (tim++ < limit));
/* disable and stop the PFPW engine */
omap_prefetch_reset(info->gpmc_cs, info);
dma_unmap_sg(info->dma->device->dev, &sg, 1, dir);
return 0;
out_copy_unmap:
dma_unmap_sg(info->dma->device->dev, &sg, 1, dir);
out_copy:
if (info->nand.options & NAND_BUSWIDTH_16)
is_write == 0 ? omap_read_buf16(mtd, (u_char *) addr, len)
: omap_write_buf16(mtd, (u_char *) addr, len);
else
is_write == 0 ? omap_read_buf8(mtd, (u_char *) addr, len)
: omap_write_buf8(mtd, (u_char *) addr, len);
return 0;
}
/**
* omap_read_buf_dma_pref - read data from NAND controller into buffer
* @mtd: MTD device structure
* @buf: buffer to store date
* @len: number of bytes to read
*/
static void omap_read_buf_dma_pref(struct mtd_info *mtd, u_char *buf, int len)
{
if (len <= mtd->oobsize)
omap_read_buf_pref(mtd, buf, len);
else
/* start transfer in DMA mode */
omap_nand_dma_transfer(mtd, buf, len, 0x0);
}
/**
* omap_write_buf_dma_pref - write buffer to NAND controller
* @mtd: MTD device structure
* @buf: data buffer
* @len: number of bytes to write
*/
static void omap_write_buf_dma_pref(struct mtd_info *mtd,
const u_char *buf, int len)
{
if (len <= mtd->oobsize)
omap_write_buf_pref(mtd, buf, len);
else
/* start transfer in DMA mode */
omap_nand_dma_transfer(mtd, (u_char *) buf, len, 0x1);
}
/*
* omap_nand_irq - GPMC irq handler
* @this_irq: gpmc irq number
* @dev: omap_nand_info structure pointer is passed here
*/
static irqreturn_t omap_nand_irq(int this_irq, void *dev)
{
struct omap_nand_info *info = (struct omap_nand_info *) dev;
u32 bytes;
bytes = readl(info->reg.gpmc_prefetch_status);
bytes = PREFETCH_STATUS_FIFO_CNT(bytes);
bytes = bytes & 0xFFFC; /* io in multiple of 4 bytes */
if (info->iomode == OMAP_NAND_IO_WRITE) { /* checks for write io */
if (this_irq == info->gpmc_irq_count)
goto done;
if (info->buf_len && (info->buf_len < bytes))
bytes = info->buf_len;
else if (!info->buf_len)
bytes = 0;
iowrite32_rep(info->nand.IO_ADDR_W,
(u32 *)info->buf, bytes >> 2);
info->buf = info->buf + bytes;
info->buf_len -= bytes;
} else {
ioread32_rep(info->nand.IO_ADDR_R,
(u32 *)info->buf, bytes >> 2);
info->buf = info->buf + bytes;
if (this_irq == info->gpmc_irq_count)
goto done;
}
return IRQ_HANDLED;
done:
complete(&info->comp);
disable_irq_nosync(info->gpmc_irq_fifo);
disable_irq_nosync(info->gpmc_irq_count);
return IRQ_HANDLED;
}
/*
* omap_read_buf_irq_pref - read data from NAND controller into buffer
* @mtd: MTD device structure
* @buf: buffer to store date
* @len: number of bytes to read
*/
static void omap_read_buf_irq_pref(struct mtd_info *mtd, u_char *buf, int len)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
int ret = 0;
if (len <= mtd->oobsize) {
omap_read_buf_pref(mtd, buf, len);
return;
}
info->iomode = OMAP_NAND_IO_READ;
info->buf = buf;
init_completion(&info->comp);
/* configure and start prefetch transfer */
ret = omap_prefetch_enable(info->gpmc_cs,
PREFETCH_FIFOTHRESHOLD_MAX/2, 0x0, len, 0x0, info);
if (ret)
/* PFPW engine is busy, use cpu copy method */
goto out_copy;
info->buf_len = len;
enable_irq(info->gpmc_irq_count);
enable_irq(info->gpmc_irq_fifo);
/* waiting for read to complete */
wait_for_completion(&info->comp);
/* disable and stop the PFPW engine */
omap_prefetch_reset(info->gpmc_cs, info);
return;
out_copy:
if (info->nand.options & NAND_BUSWIDTH_16)
omap_read_buf16(mtd, buf, len);
else
omap_read_buf8(mtd, buf, len);
}
/*
* omap_write_buf_irq_pref - write buffer to NAND controller
* @mtd: MTD device structure
* @buf: data buffer
* @len: number of bytes to write
*/
static void omap_write_buf_irq_pref(struct mtd_info *mtd,
const u_char *buf, int len)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
int ret = 0;
unsigned long tim, limit;
u32 val;
if (len <= mtd->oobsize) {
omap_write_buf_pref(mtd, buf, len);
return;
}
info->iomode = OMAP_NAND_IO_WRITE;
info->buf = (u_char *) buf;
init_completion(&info->comp);
/* configure and start prefetch transfer : size=24 */
ret = omap_prefetch_enable(info->gpmc_cs,
(PREFETCH_FIFOTHRESHOLD_MAX * 3) / 8, 0x0, len, 0x1, info);
if (ret)
/* PFPW engine is busy, use cpu copy method */
goto out_copy;
info->buf_len = len;
enable_irq(info->gpmc_irq_count);
enable_irq(info->gpmc_irq_fifo);
/* waiting for write to complete */
wait_for_completion(&info->comp);
/* wait for data to flushed-out before reset the prefetch */
tim = 0;
limit = (loops_per_jiffy * msecs_to_jiffies(OMAP_NAND_TIMEOUT_MS));
do {
val = readl(info->reg.gpmc_prefetch_status);
val = PREFETCH_STATUS_COUNT(val);
cpu_relax();
} while (val && (tim++ < limit));
/* disable and stop the PFPW engine */
omap_prefetch_reset(info->gpmc_cs, info);
return;
out_copy:
if (info->nand.options & NAND_BUSWIDTH_16)
omap_write_buf16(mtd, buf, len);
else
omap_write_buf8(mtd, buf, len);
}
/**
* gen_true_ecc - This function will generate true ECC value
* @ecc_buf: buffer to store ecc code
*
* This generated true ECC value can be used when correcting
* data read from NAND flash memory core
*/
static void gen_true_ecc(u8 *ecc_buf)
{
u32 tmp = ecc_buf[0] | (ecc_buf[1] << 16) |
((ecc_buf[2] & 0xF0) << 20) | ((ecc_buf[2] & 0x0F) << 8);
ecc_buf[0] = ~(P64o(tmp) | P64e(tmp) | P32o(tmp) | P32e(tmp) |
P16o(tmp) | P16e(tmp) | P8o(tmp) | P8e(tmp));
ecc_buf[1] = ~(P1024o(tmp) | P1024e(tmp) | P512o(tmp) | P512e(tmp) |
P256o(tmp) | P256e(tmp) | P128o(tmp) | P128e(tmp));
ecc_buf[2] = ~(P4o(tmp) | P4e(tmp) | P2o(tmp) | P2e(tmp) | P1o(tmp) |
P1e(tmp) | P2048o(tmp) | P2048e(tmp));
}
/**
* omap_compare_ecc - Detect (2 bits) and correct (1 bit) error in data
* @ecc_data1: ecc code from nand spare area
* @ecc_data2: ecc code from hardware register obtained from hardware ecc
* @page_data: page data
*
* This function compares two ECC's and indicates if there is an error.
* If the error can be corrected it will be corrected to the buffer.
* If there is no error, %0 is returned. If there is an error but it
* was corrected, %1 is returned. Otherwise, %-1 is returned.
*/
static int omap_compare_ecc(u8 *ecc_data1, /* read from NAND memory */
u8 *ecc_data2, /* read from register */
u8 *page_data)
{
uint i;
u8 tmp0_bit[8], tmp1_bit[8], tmp2_bit[8];
u8 comp0_bit[8], comp1_bit[8], comp2_bit[8];
u8 ecc_bit[24];
u8 ecc_sum = 0;
u8 find_bit = 0;
uint find_byte = 0;
int isEccFF;
isEccFF = ((*(u32 *)ecc_data1 & 0xFFFFFF) == 0xFFFFFF);
gen_true_ecc(ecc_data1);
gen_true_ecc(ecc_data2);
for (i = 0; i <= 2; i++) {
*(ecc_data1 + i) = ~(*(ecc_data1 + i));
*(ecc_data2 + i) = ~(*(ecc_data2 + i));
}
for (i = 0; i < 8; i++) {
tmp0_bit[i] = *ecc_data1 % 2;
*ecc_data1 = *ecc_data1 / 2;
}
for (i = 0; i < 8; i++) {
tmp1_bit[i] = *(ecc_data1 + 1) % 2;
*(ecc_data1 + 1) = *(ecc_data1 + 1) / 2;
}
for (i = 0; i < 8; i++) {
tmp2_bit[i] = *(ecc_data1 + 2) % 2;
*(ecc_data1 + 2) = *(ecc_data1 + 2) / 2;
}
for (i = 0; i < 8; i++) {
comp0_bit[i] = *ecc_data2 % 2;
*ecc_data2 = *ecc_data2 / 2;
}
for (i = 0; i < 8; i++) {
comp1_bit[i] = *(ecc_data2 + 1) % 2;
*(ecc_data2 + 1) = *(ecc_data2 + 1) / 2;
}
for (i = 0; i < 8; i++) {
comp2_bit[i] = *(ecc_data2 + 2) % 2;
*(ecc_data2 + 2) = *(ecc_data2 + 2) / 2;
}
for (i = 0; i < 6; i++)
ecc_bit[i] = tmp2_bit[i + 2] ^ comp2_bit[i + 2];
for (i = 0; i < 8; i++)
ecc_bit[i + 6] = tmp0_bit[i] ^ comp0_bit[i];
for (i = 0; i < 8; i++)
ecc_bit[i + 14] = tmp1_bit[i] ^ comp1_bit[i];
ecc_bit[22] = tmp2_bit[0] ^ comp2_bit[0];
ecc_bit[23] = tmp2_bit[1] ^ comp2_bit[1];
for (i = 0; i < 24; i++)
ecc_sum += ecc_bit[i];
switch (ecc_sum) {
case 0:
/* Not reached because this function is not called if
* ECC values are equal
*/
return 0;
case 1:
/* Uncorrectable error */
pr_debug("ECC UNCORRECTED_ERROR 1\n");
return -1;
case 11:
/* UN-Correctable error */
pr_debug("ECC UNCORRECTED_ERROR B\n");
return -1;
case 12:
/* Correctable error */
find_byte = (ecc_bit[23] << 8) +
(ecc_bit[21] << 7) +
(ecc_bit[19] << 6) +
(ecc_bit[17] << 5) +
(ecc_bit[15] << 4) +
(ecc_bit[13] << 3) +
(ecc_bit[11] << 2) +
(ecc_bit[9] << 1) +
ecc_bit[7];
find_bit = (ecc_bit[5] << 2) + (ecc_bit[3] << 1) + ecc_bit[1];
pr_debug("Correcting single bit ECC error at offset: "
"%d, bit: %d\n", find_byte, find_bit);
page_data[find_byte] ^= (1 << find_bit);
return 1;
default:
if (isEccFF) {
if (ecc_data2[0] == 0 &&
ecc_data2[1] == 0 &&
ecc_data2[2] == 0)
return 0;
}
pr_debug("UNCORRECTED_ERROR default\n");
return -1;
}
}
/**
* omap_correct_data - Compares the ECC read with HW generated ECC
* @mtd: MTD device structure
* @dat: page data
* @read_ecc: ecc read from nand flash
* @calc_ecc: ecc read from HW ECC registers
*
* Compares the ecc read from nand spare area with ECC registers values
* and if ECC's mismatched, it will call 'omap_compare_ecc' for error
* detection and correction. If there are no errors, %0 is returned. If
* there were errors and all of the errors were corrected, the number of
* corrected errors is returned. If uncorrectable errors exist, %-1 is
* returned.
*/
static int omap_correct_data(struct mtd_info *mtd, u_char *dat,
u_char *read_ecc, u_char *calc_ecc)
{
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
int blockCnt = 0, i = 0, ret = 0;
int stat = 0;
/* Ex NAND_ECC_HW12_2048 */
if ((info->nand.ecc.mode == NAND_ECC_HW) &&
(info->nand.ecc.size == 2048))
blockCnt = 4;
else
blockCnt = 1;
for (i = 0; i < blockCnt; i++) {
if (memcmp(read_ecc, calc_ecc, 3) != 0) {
ret = omap_compare_ecc(read_ecc, calc_ecc, dat);
if (ret < 0)
return ret;
/* keep track of the number of corrected errors */
stat += ret;
}
read_ecc += 3;
calc_ecc += 3;
dat += 512;
}
return stat;
}
/**
* omap_calcuate_ecc - Generate non-inverted ECC bytes.
* @mtd: MTD device structure
* @dat: The pointer to data on which ecc is computed
* @ecc_code: The ecc_code buffer
*
* Using noninverted ECC can be considered ugly since writing a blank
* page ie. padding will clear the ECC bytes. This is no problem as long
* nobody is trying to write data on the seemingly unused page. Reading
* an erased page will produce an ECC mismatch between generated and read
* ECC bytes that has to be dealt with separately.
*/
static int omap_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
u_char *ecc_code)
{
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
u32 val;
val = readl(info->reg.gpmc_ecc_config);
if (((val >> ECC_CONFIG_CS_SHIFT) & CS_MASK) != info->gpmc_cs)
return -EINVAL;
/* read ecc result */
val = readl(info->reg.gpmc_ecc1_result);
*ecc_code++ = val; /* P128e, ..., P1e */
*ecc_code++ = val >> 16; /* P128o, ..., P1o */
/* P2048o, P1024o, P512o, P256o, P2048e, P1024e, P512e, P256e */
*ecc_code++ = ((val >> 8) & 0x0f) | ((val >> 20) & 0xf0);
return 0;
}
/**
* omap_enable_hwecc - This function enables the hardware ecc functionality
* @mtd: MTD device structure
* @mode: Read/Write mode
*/
static void omap_enable_hwecc(struct mtd_info *mtd, int mode)
{
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
struct nand_chip *chip = mtd->priv;
unsigned int dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0;
u32 val;
/* clear ecc and enable bits */
val = ECCCLEAR | ECC1;
writel(val, info->reg.gpmc_ecc_control);
/* program ecc and result sizes */
val = ((((info->nand.ecc.size >> 1) - 1) << ECCSIZE1_SHIFT) |
ECC1RESULTSIZE);
writel(val, info->reg.gpmc_ecc_size_config);
switch (mode) {
case NAND_ECC_READ:
case NAND_ECC_WRITE:
writel(ECCCLEAR | ECC1, info->reg.gpmc_ecc_control);
break;
case NAND_ECC_READSYN:
writel(ECCCLEAR, info->reg.gpmc_ecc_control);
break;
default:
dev_info(&info->pdev->dev,
"error: unrecognized Mode[%d]!\n", mode);
break;
}
/* (ECC 16 or 8 bit col) | ( CS ) | ECC Enable */
val = (dev_width << 7) | (info->gpmc_cs << 1) | (0x1);
writel(val, info->reg.gpmc_ecc_config);
}
/**
* omap_wait - wait until the command is done
* @mtd: MTD device structure
* @chip: NAND Chip structure
*
* Wait function is called during Program and erase operations and
* the way it is called from MTD layer, we should wait till the NAND
* chip is ready after the programming/erase operation has completed.
*
* Erase can take up to 400ms and program up to 20ms according to
* general NAND and SmartMedia specs
*/
static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip)
{
struct nand_chip *this = mtd->priv;
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
unsigned long timeo = jiffies;
int status, state = this->state;
if (state == FL_ERASING)
timeo += msecs_to_jiffies(400);
else
timeo += msecs_to_jiffies(20);
writeb(NAND_CMD_STATUS & 0xFF, info->reg.gpmc_nand_command);
while (time_before(jiffies, timeo)) {
status = readb(info->reg.gpmc_nand_data);
if (status & NAND_STATUS_READY)
break;
cond_resched();
}
status = readb(info->reg.gpmc_nand_data);
return status;
}
/**
* omap_dev_ready - calls the platform specific dev_ready function
* @mtd: MTD device structure
*/
static int omap_dev_ready(struct mtd_info *mtd)
{
unsigned int val = 0;
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
val = readl(info->reg.gpmc_status);
if ((val & 0x100) == 0x100) {
return 1;
} else {
return 0;
}
}
/**
* omap_enable_hwecc_bch - Program GPMC to perform BCH ECC calculation
* @mtd: MTD device structure
* @mode: Read/Write mode
*
* When using BCH, sector size is hardcoded to 512 bytes.
* Using wrapping mode 6 both for reading and writing if ELM module not uses
* for error correction.
* On writing,
* eccsize0 = 0 (no additional protected byte in spare area)
* eccsize1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area)
*/
static void __maybe_unused omap_enable_hwecc_bch(struct mtd_info *mtd, int mode)
{
unsigned int bch_type;
unsigned int dev_width, nsectors;
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
enum omap_ecc ecc_opt = info->ecc_opt;
struct nand_chip *chip = mtd->priv;
u32 val, wr_mode;
unsigned int ecc_size1, ecc_size0;
/* GPMC configurations for calculating ECC */
switch (ecc_opt) {
case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
bch_type = 0;
nsectors = 1;
if (mode == NAND_ECC_READ) {
wr_mode = BCH_WRAPMODE_6;
ecc_size0 = BCH_ECC_SIZE0;
ecc_size1 = BCH_ECC_SIZE1;
} else {
wr_mode = BCH_WRAPMODE_6;
ecc_size0 = BCH_ECC_SIZE0;
ecc_size1 = BCH_ECC_SIZE1;
}
break;
case OMAP_ECC_BCH4_CODE_HW:
bch_type = 0;
nsectors = chip->ecc.steps;
if (mode == NAND_ECC_READ) {
wr_mode = BCH_WRAPMODE_1;
ecc_size0 = BCH4R_ECC_SIZE0;
ecc_size1 = BCH4R_ECC_SIZE1;
} else {
wr_mode = BCH_WRAPMODE_6;
ecc_size0 = BCH_ECC_SIZE0;
ecc_size1 = BCH_ECC_SIZE1;
}
break;
case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
bch_type = 1;
nsectors = 1;
if (mode == NAND_ECC_READ) {
wr_mode = BCH_WRAPMODE_6;
ecc_size0 = BCH_ECC_SIZE0;
ecc_size1 = BCH_ECC_SIZE1;
} else {
wr_mode = BCH_WRAPMODE_6;
ecc_size0 = BCH_ECC_SIZE0;
ecc_size1 = BCH_ECC_SIZE1;
}
break;
case OMAP_ECC_BCH8_CODE_HW:
bch_type = 1;
nsectors = chip->ecc.steps;
if (mode == NAND_ECC_READ) {
wr_mode = BCH_WRAPMODE_1;
ecc_size0 = BCH8R_ECC_SIZE0;
ecc_size1 = BCH8R_ECC_SIZE1;
} else {
wr_mode = BCH_WRAPMODE_6;
ecc_size0 = BCH_ECC_SIZE0;
ecc_size1 = BCH_ECC_SIZE1;
}
break;
case OMAP_ECC_BCH16_CODE_HW:
bch_type = 0x2;
nsectors = chip->ecc.steps;
if (mode == NAND_ECC_READ) {
wr_mode = 0x01;
ecc_size0 = 52; /* ECC bits in nibbles per sector */
ecc_size1 = 0; /* non-ECC bits in nibbles per sector */
} else {
wr_mode = 0x01;
ecc_size0 = 0; /* extra bits in nibbles per sector */
ecc_size1 = 52; /* OOB bits in nibbles per sector */
}
break;
default:
return;
}
writel(ECC1, info->reg.gpmc_ecc_control);
/* Configure ecc size for BCH */
val = (ecc_size1 << ECCSIZE1_SHIFT) | (ecc_size0 << ECCSIZE0_SHIFT);
writel(val, info->reg.gpmc_ecc_size_config);
dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0;
/* BCH configuration */
val = ((1 << 16) | /* enable BCH */
(bch_type << 12) | /* BCH4/BCH8/BCH16 */
(wr_mode << 8) | /* wrap mode */
(dev_width << 7) | /* bus width */
(((nsectors-1) & 0x7) << 4) | /* number of sectors */
(info->gpmc_cs << 1) | /* ECC CS */
(0x1)); /* enable ECC */
writel(val, info->reg.gpmc_ecc_config);
/* Clear ecc and enable bits */
writel(ECCCLEAR | ECC1, info->reg.gpmc_ecc_control);
}
static u8 bch4_polynomial[] = {0x28, 0x13, 0xcc, 0x39, 0x96, 0xac, 0x7f};
static u8 bch8_polynomial[] = {0xef, 0x51, 0x2e, 0x09, 0xed, 0x93, 0x9a, 0xc2,
0x97, 0x79, 0xe5, 0x24, 0xb5};
/**
* omap_calculate_ecc_bch - Generate bytes of ECC bytes
* @mtd: MTD device structure
* @dat: The pointer to data on which ecc is computed
* @ecc_code: The ecc_code buffer
*
* Support calculating of BCH4/8 ecc vectors for the page
*/
static int __maybe_unused omap_calculate_ecc_bch(struct mtd_info *mtd,
const u_char *dat, u_char *ecc_calc)
{
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
int eccbytes = info->nand.ecc.bytes;
struct gpmc_nand_regs *gpmc_regs = &info->reg;
u8 *ecc_code;
unsigned long nsectors, bch_val1, bch_val2, bch_val3, bch_val4;
u32 val;
int i, j;
nsectors = ((readl(info->reg.gpmc_ecc_config) >> 4) & 0x7) + 1;
for (i = 0; i < nsectors; i++) {
ecc_code = ecc_calc;
switch (info->ecc_opt) {
case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
case OMAP_ECC_BCH8_CODE_HW:
bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]);
bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]);
bch_val3 = readl(gpmc_regs->gpmc_bch_result2[i]);
bch_val4 = readl(gpmc_regs->gpmc_bch_result3[i]);
*ecc_code++ = (bch_val4 & 0xFF);
*ecc_code++ = ((bch_val3 >> 24) & 0xFF);
*ecc_code++ = ((bch_val3 >> 16) & 0xFF);
*ecc_code++ = ((bch_val3 >> 8) & 0xFF);
*ecc_code++ = (bch_val3 & 0xFF);
*ecc_code++ = ((bch_val2 >> 24) & 0xFF);
*ecc_code++ = ((bch_val2 >> 16) & 0xFF);
*ecc_code++ = ((bch_val2 >> 8) & 0xFF);
*ecc_code++ = (bch_val2 & 0xFF);
*ecc_code++ = ((bch_val1 >> 24) & 0xFF);
*ecc_code++ = ((bch_val1 >> 16) & 0xFF);
*ecc_code++ = ((bch_val1 >> 8) & 0xFF);
*ecc_code++ = (bch_val1 & 0xFF);
break;
case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
case OMAP_ECC_BCH4_CODE_HW:
bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]);
bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]);
*ecc_code++ = ((bch_val2 >> 12) & 0xFF);
*ecc_code++ = ((bch_val2 >> 4) & 0xFF);
*ecc_code++ = ((bch_val2 & 0xF) << 4) |
((bch_val1 >> 28) & 0xF);
*ecc_code++ = ((bch_val1 >> 20) & 0xFF);
*ecc_code++ = ((bch_val1 >> 12) & 0xFF);
*ecc_code++ = ((bch_val1 >> 4) & 0xFF);
*ecc_code++ = ((bch_val1 & 0xF) << 4);
break;
case OMAP_ECC_BCH16_CODE_HW:
val = readl(gpmc_regs->gpmc_bch_result6[i]);
ecc_code[0] = ((val >> 8) & 0xFF);
ecc_code[1] = ((val >> 0) & 0xFF);
val = readl(gpmc_regs->gpmc_bch_result5[i]);
ecc_code[2] = ((val >> 24) & 0xFF);
ecc_code[3] = ((val >> 16) & 0xFF);
ecc_code[4] = ((val >> 8) & 0xFF);
ecc_code[5] = ((val >> 0) & 0xFF);
val = readl(gpmc_regs->gpmc_bch_result4[i]);
ecc_code[6] = ((val >> 24) & 0xFF);
ecc_code[7] = ((val >> 16) & 0xFF);
ecc_code[8] = ((val >> 8) & 0xFF);
ecc_code[9] = ((val >> 0) & 0xFF);
val = readl(gpmc_regs->gpmc_bch_result3[i]);
ecc_code[10] = ((val >> 24) & 0xFF);
ecc_code[11] = ((val >> 16) & 0xFF);
ecc_code[12] = ((val >> 8) & 0xFF);
ecc_code[13] = ((val >> 0) & 0xFF);
val = readl(gpmc_regs->gpmc_bch_result2[i]);
ecc_code[14] = ((val >> 24) & 0xFF);
ecc_code[15] = ((val >> 16) & 0xFF);
ecc_code[16] = ((val >> 8) & 0xFF);
ecc_code[17] = ((val >> 0) & 0xFF);
val = readl(gpmc_regs->gpmc_bch_result1[i]);
ecc_code[18] = ((val >> 24) & 0xFF);
ecc_code[19] = ((val >> 16) & 0xFF);
ecc_code[20] = ((val >> 8) & 0xFF);
ecc_code[21] = ((val >> 0) & 0xFF);
val = readl(gpmc_regs->gpmc_bch_result0[i]);
ecc_code[22] = ((val >> 24) & 0xFF);
ecc_code[23] = ((val >> 16) & 0xFF);
ecc_code[24] = ((val >> 8) & 0xFF);
ecc_code[25] = ((val >> 0) & 0xFF);
break;
default:
return -EINVAL;
}
/* ECC scheme specific syndrome customizations */
switch (info->ecc_opt) {
case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
/* Add constant polynomial to remainder, so that
* ECC of blank pages results in 0x0 on reading back */
for (j = 0; j < eccbytes; j++)
ecc_calc[j] ^= bch4_polynomial[j];
break;
case OMAP_ECC_BCH4_CODE_HW:
/* Set 8th ECC byte as 0x0 for ROM compatibility */
ecc_calc[eccbytes - 1] = 0x0;
break;
case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
/* Add constant polynomial to remainder, so that
* ECC of blank pages results in 0x0 on reading back */
for (j = 0; j < eccbytes; j++)
ecc_calc[j] ^= bch8_polynomial[j];
break;
case OMAP_ECC_BCH8_CODE_HW:
/* Set 14th ECC byte as 0x0 for ROM compatibility */
ecc_calc[eccbytes - 1] = 0x0;
break;
case OMAP_ECC_BCH16_CODE_HW:
break;
default:
return -EINVAL;
}
ecc_calc += eccbytes;
}
return 0;
}
#ifdef CONFIG_MTD_NAND_OMAP_BCH
/**
* erased_sector_bitflips - count bit flips
* @data: data sector buffer
* @oob: oob buffer
* @info: omap_nand_info
*
* Check the bit flips in erased page falls below correctable level.
* If falls below, report the page as erased with correctable bit
* flip, else report as uncorrectable page.
*/
static int erased_sector_bitflips(u_char *data, u_char *oob,
struct omap_nand_info *info)
{
int flip_bits = 0, i;
for (i = 0; i < info->nand.ecc.size; i++) {
flip_bits += hweight8(~data[i]);
if (flip_bits > info->nand.ecc.strength)
return 0;
}
for (i = 0; i < info->nand.ecc.bytes - 1; i++) {
flip_bits += hweight8(~oob[i]);
if (flip_bits > info->nand.ecc.strength)
return 0;
}
/*
* Bit flips falls in correctable level.
* Fill data area with 0xFF
*/
if (flip_bits) {
memset(data, 0xFF, info->nand.ecc.size);
memset(oob, 0xFF, info->nand.ecc.bytes);
}
return flip_bits;
}
/**
* omap_elm_correct_data - corrects page data area in case error reported
* @mtd: MTD device structure
* @data: page data
* @read_ecc: ecc read from nand flash
* @calc_ecc: ecc read from HW ECC registers
*
* Calculated ecc vector reported as zero in case of non-error pages.
* In case of non-zero ecc vector, first filter out erased-pages, and
* then process data via ELM to detect bit-flips.
*/
static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data,
u_char *read_ecc, u_char *calc_ecc)
{
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
struct nand_ecc_ctrl *ecc = &info->nand.ecc;
int eccsteps = info->nand.ecc.steps;
int i , j, stat = 0;
int eccflag, actual_eccbytes;
struct elm_errorvec err_vec[ERROR_VECTOR_MAX];
u_char *ecc_vec = calc_ecc;
u_char *spare_ecc = read_ecc;
u_char *erased_ecc_vec;
u_char *buf;
int bitflip_count;
bool is_error_reported = false;
u32 bit_pos, byte_pos, error_max, pos;
int err;
switch (info->ecc_opt) {
case OMAP_ECC_BCH4_CODE_HW:
/* omit 7th ECC byte reserved for ROM code compatibility */
actual_eccbytes = ecc->bytes - 1;
erased_ecc_vec = bch4_vector;
break;
case OMAP_ECC_BCH8_CODE_HW:
/* omit 14th ECC byte reserved for ROM code compatibility */
actual_eccbytes = ecc->bytes - 1;
erased_ecc_vec = bch8_vector;
break;
case OMAP_ECC_BCH16_CODE_HW:
actual_eccbytes = ecc->bytes;
erased_ecc_vec = bch16_vector;
break;
default:
pr_err("invalid driver configuration\n");
return -EINVAL;
}
/* Initialize elm error vector to zero */
memset(err_vec, 0, sizeof(err_vec));
for (i = 0; i < eccsteps ; i++) {
eccflag = 0; /* initialize eccflag */
/*
* Check any error reported,
* In case of error, non zero ecc reported.
*/
for (j = 0; j < actual_eccbytes; j++) {
if (calc_ecc[j] != 0) {
eccflag = 1; /* non zero ecc, error present */
break;
}
}
if (eccflag == 1) {
if (memcmp(calc_ecc, erased_ecc_vec,
actual_eccbytes) == 0) {
/*
* calc_ecc[] matches pattern for ECC(all 0xff)
* so this is definitely an erased-page
*/
} else {
buf = &data[info->nand.ecc.size * i];
/*
* count number of 0-bits in read_buf.
* This check can be removed once a similar
* check is introduced in generic NAND driver
*/
bitflip_count = erased_sector_bitflips(
buf, read_ecc, info);
if (bitflip_count) {
/*
* number of 0-bits within ECC limits
* So this may be an erased-page
*/
stat += bitflip_count;
} else {
/*
* Too many 0-bits. It may be a
* - programmed-page, OR
* - erased-page with many bit-flips
* So this page requires check by ELM
*/
err_vec[i].error_reported = true;
is_error_reported = true;
}
}
}
/* Update the ecc vector */
calc_ecc += ecc->bytes;
read_ecc += ecc->bytes;
}
/* Check if any error reported */
if (!is_error_reported)
return stat;
/* Decode BCH error using ELM module */
elm_decode_bch_error_page(info->elm_dev, ecc_vec, err_vec);
err = 0;
for (i = 0; i < eccsteps; i++) {
if (err_vec[i].error_uncorrectable) {
pr_err("nand: uncorrectable bit-flips found\n");
err = -EBADMSG;
} else if (err_vec[i].error_reported) {
for (j = 0; j < err_vec[i].error_count; j++) {
switch (info->ecc_opt) {
case OMAP_ECC_BCH4_CODE_HW:
/* Add 4 bits to take care of padding */
pos = err_vec[i].error_loc[j] +
BCH4_BIT_PAD;
break;
case OMAP_ECC_BCH8_CODE_HW:
case OMAP_ECC_BCH16_CODE_HW:
pos = err_vec[i].error_loc[j];
break;
default:
return -EINVAL;
}
error_max = (ecc->size + actual_eccbytes) * 8;
/* Calculate bit position of error */
bit_pos = pos % 8;
/* Calculate byte position of error */
byte_pos = (error_max - pos - 1) / 8;
if (pos < error_max) {
if (byte_pos < 512) {
pr_debug("bitflip@dat[%d]=%x\n",
byte_pos, data[byte_pos]);
data[byte_pos] ^= 1 << bit_pos;
} else {
pr_debug("bitflip@oob[%d]=%x\n",
(byte_pos - 512),
spare_ecc[byte_pos - 512]);
spare_ecc[byte_pos - 512] ^=
1 << bit_pos;
}
} else {
pr_err("invalid bit-flip @ %d:%d\n",
byte_pos, bit_pos);
err = -EBADMSG;
}
}
}
/* Update number of correctable errors */
stat += err_vec[i].error_count;
/* Update page data with sector size */
data += ecc->size;
spare_ecc += ecc->bytes;
}
return (err) ? err : stat;
}
/**
* omap_write_page_bch - BCH ecc based write page function for entire page
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: data buffer
* @oob_required: must write chip->oob_poi to OOB
*
* Custom write page method evolved to support multi sector writing in one shot
*/
static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
const uint8_t *buf, int oob_required)
{
int i;
uint8_t *ecc_calc = chip->buffers->ecccalc;
uint32_t *eccpos = chip->ecc.layout->eccpos;
/* Enable GPMC ecc engine */
chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
/* Write data */
chip->write_buf(mtd, buf, mtd->writesize);
/* Update ecc vector from GPMC result registers */
chip->ecc.calculate(mtd, buf, &ecc_calc[0]);
for (i = 0; i < chip->ecc.total; i++)
chip->oob_poi[eccpos[i]] = ecc_calc[i];
/* Write ecc vector to OOB area */
chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
return 0;
}
/**
* omap_read_page_bch - BCH ecc based page read function for entire page
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: buffer to store read data
* @oob_required: caller requires OOB data read to chip->oob_poi
* @page: page number to read
*
* For BCH ecc scheme, GPMC used for syndrome calculation and ELM module
* used for error correction.
* Custom method evolved to support ELM error correction & multi sector
* reading. On reading page data area is read along with OOB data with
* ecc engine enabled. ecc vector updated after read of OOB data.
* For non error pages ecc vector reported as zero.
*/
static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
uint8_t *buf, int oob_required, int page)
{
uint8_t *ecc_calc = chip->buffers->ecccalc;
uint8_t *ecc_code = chip->buffers->ecccode;
uint32_t *eccpos = chip->ecc.layout->eccpos;
uint8_t *oob = &chip->oob_poi[eccpos[0]];
uint32_t oob_pos = mtd->writesize + chip->ecc.layout->eccpos[0];
int stat;
unsigned int max_bitflips = 0;
/* Enable GPMC ecc engine */
chip->ecc.hwctl(mtd, NAND_ECC_READ);
/* Read data */
chip->read_buf(mtd, buf, mtd->writesize);
/* Read oob bytes */
chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, -1);
chip->read_buf(mtd, oob, chip->ecc.total);
/* Calculate ecc bytes */
chip->ecc.calculate(mtd, buf, ecc_calc);
memcpy(ecc_code, &chip->oob_poi[eccpos[0]], chip->ecc.total);
stat = chip->ecc.correct(mtd, buf, ecc_code, ecc_calc);
if (stat < 0) {
mtd->ecc_stats.failed++;
} else {
mtd->ecc_stats.corrected += stat;
max_bitflips = max_t(unsigned int, max_bitflips, stat);
}
return max_bitflips;
}
/**
* is_elm_present - checks for presence of ELM module by scanning DT nodes
* @omap_nand_info: NAND device structure containing platform data
* @bch_type: 0x0=BCH4, 0x1=BCH8, 0x2=BCH16
*/
static int is_elm_present(struct omap_nand_info *info,
struct device_node *elm_node, enum bch_ecc bch_type)
{
struct platform_device *pdev;
struct nand_ecc_ctrl *ecc = &info->nand.ecc;
int err;
/* check whether elm-id is passed via DT */
if (!elm_node) {
pr_err("nand: error: ELM DT node not found\n");
return -ENODEV;
}
pdev = of_find_device_by_node(elm_node);
/* check whether ELM device is registered */
if (!pdev) {
pr_err("nand: error: ELM device not found\n");
return -ENODEV;
}
/* ELM module available, now configure it */
info->elm_dev = &pdev->dev;
err = elm_config(info->elm_dev, bch_type,
(info->mtd.writesize / ecc->size), ecc->size, ecc->bytes);
return err;
}
#endif /* CONFIG_MTD_NAND_ECC_BCH */
static int omap_nand_probe(struct platform_device *pdev)
{
struct omap_nand_info *info;
struct omap_nand_platform_data *pdata;
struct mtd_info *mtd;
struct nand_chip *nand_chip;
struct nand_ecclayout *ecclayout;
int err;
int i;
dma_cap_mask_t mask;
unsigned sig;
unsigned oob_index;
struct resource *res;
struct mtd_part_parser_data ppdata = {};
pdata = dev_get_platdata(&pdev->dev);
if (pdata == NULL) {
dev_err(&pdev->dev, "platform data missing\n");
return -ENODEV;
}
info = devm_kzalloc(&pdev->dev, sizeof(struct omap_nand_info),
GFP_KERNEL);
if (!info)
return -ENOMEM;
platform_set_drvdata(pdev, info);
spin_lock_init(&info->controller.lock);
init_waitqueue_head(&info->controller.wq);
info->pdev = pdev;
info->gpmc_cs = pdata->cs;
info->reg = pdata->reg;
info->of_node = pdata->of_node;
info->ecc_opt = pdata->ecc_opt;
mtd = &info->mtd;
mtd->priv = &info->nand;
mtd->name = dev_name(&pdev->dev);
mtd->owner = THIS_MODULE;
nand_chip = &info->nand;
nand_chip->ecc.priv = NULL;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
nand_chip->IO_ADDR_R = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(nand_chip->IO_ADDR_R))
return PTR_ERR(nand_chip->IO_ADDR_R);
info->phys_base = res->start;
nand_chip->controller = &info->controller;
nand_chip->IO_ADDR_W = nand_chip->IO_ADDR_R;
nand_chip->cmd_ctrl = omap_hwcontrol;
/*
* If RDY/BSY line is connected to OMAP then use the omap ready
* function and the generic nand_wait function which reads the status
* register after monitoring the RDY/BSY line. Otherwise use a standard
* chip delay which is slightly more than tR (AC Timing) of the NAND
* device and read status register until you get a failure or success
*/
if (pdata->dev_ready) {
nand_chip->dev_ready = omap_dev_ready;
nand_chip->chip_delay = 0;
} else {
nand_chip->waitfunc = omap_wait;
nand_chip->chip_delay = 50;
}
if (pdata->flash_bbt)
nand_chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB;
else
nand_chip->options |= NAND_SKIP_BBTSCAN;
/* scan NAND device connected to chip controller */
nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16;
if (nand_scan_ident(mtd, 1, NULL)) {
pr_err("nand device scan failed, may be bus-width mismatch\n");
err = -ENXIO;
goto return_error;
}
/* check for small page devices */
if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) {
pr_err("small page devices are not supported\n");
err = -EINVAL;
goto return_error;
}
/* re-populate low-level callbacks based on xfer modes */
switch (pdata->xfer_type) {
case NAND_OMAP_PREFETCH_POLLED:
nand_chip->read_buf = omap_read_buf_pref;
nand_chip->write_buf = omap_write_buf_pref;
break;
case NAND_OMAP_POLLED:
/* Use nand_base defaults for {read,write}_buf */
break;
case NAND_OMAP_PREFETCH_DMA:
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
sig = OMAP24XX_DMA_GPMC;
info->dma = dma_request_channel(mask, omap_dma_filter_fn, &sig);
if (!info->dma) {
dev_err(&pdev->dev, "DMA engine request failed\n");
err = -ENXIO;
goto return_error;
} else {
struct dma_slave_config cfg;
memset(&cfg, 0, sizeof(cfg));
cfg.src_addr = info->phys_base;
cfg.dst_addr = info->phys_base;
cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
cfg.src_maxburst = 16;
cfg.dst_maxburst = 16;
err = dmaengine_slave_config(info->dma, &cfg);
if (err) {
dev_err(&pdev->dev, "DMA engine slave config failed: %d\n",
err);
goto return_error;
}
nand_chip->read_buf = omap_read_buf_dma_pref;
nand_chip->write_buf = omap_write_buf_dma_pref;
}
break;
case NAND_OMAP_PREFETCH_IRQ:
info->gpmc_irq_fifo = platform_get_irq(pdev, 0);
if (info->gpmc_irq_fifo <= 0) {
dev_err(&pdev->dev, "error getting fifo irq\n");
err = -ENODEV;
goto return_error;
}
err = devm_request_irq(&pdev->dev, info->gpmc_irq_fifo,
omap_nand_irq, IRQF_SHARED,
"gpmc-nand-fifo", info);
if (err) {
dev_err(&pdev->dev, "requesting irq(%d) error:%d",
info->gpmc_irq_fifo, err);
info->gpmc_irq_fifo = 0;
goto return_error;
}
info->gpmc_irq_count = platform_get_irq(pdev, 1);
if (info->gpmc_irq_count <= 0) {
dev_err(&pdev->dev, "error getting count irq\n");
err = -ENODEV;
goto return_error;
}
err = devm_request_irq(&pdev->dev, info->gpmc_irq_count,
omap_nand_irq, IRQF_SHARED,
"gpmc-nand-count", info);
if (err) {
dev_err(&pdev->dev, "requesting irq(%d) error:%d",
info->gpmc_irq_count, err);
info->gpmc_irq_count = 0;
goto return_error;
}
nand_chip->read_buf = omap_read_buf_irq_pref;
nand_chip->write_buf = omap_write_buf_irq_pref;
break;
default:
dev_err(&pdev->dev,
"xfer_type(%d) not supported!\n", pdata->xfer_type);
err = -EINVAL;
goto return_error;
}
/* populate MTD interface based on ECC scheme */
ecclayout = &omap_oobinfo;
switch (info->ecc_opt) {
case OMAP_ECC_HAM1_CODE_SW:
nand_chip->ecc.mode = NAND_ECC_SOFT;
break;
case OMAP_ECC_HAM1_CODE_HW:
pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n");
nand_chip->ecc.mode = NAND_ECC_HW;
nand_chip->ecc.bytes = 3;
nand_chip->ecc.size = 512;
nand_chip->ecc.strength = 1;
nand_chip->ecc.calculate = omap_calculate_ecc;
nand_chip->ecc.hwctl = omap_enable_hwecc;
nand_chip->ecc.correct = omap_correct_data;
/* define ECC layout */
ecclayout->eccbytes = nand_chip->ecc.bytes *
(mtd->writesize /
nand_chip->ecc.size);
if (nand_chip->options & NAND_BUSWIDTH_16)
oob_index = BADBLOCK_MARKER_LENGTH;
else
oob_index = 1;
for (i = 0; i < ecclayout->eccbytes; i++, oob_index++)
ecclayout->eccpos[i] = oob_index;
/* no reserved-marker in ecclayout for this ecc-scheme */
ecclayout->oobfree->offset =
ecclayout->eccpos[ecclayout->eccbytes - 1] + 1;
break;
case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
#ifdef CONFIG_MTD_NAND_ECC_BCH
pr_info("nand: using OMAP_ECC_BCH4_CODE_HW_DETECTION_SW\n");
nand_chip->ecc.mode = NAND_ECC_HW;
nand_chip->ecc.size = 512;
nand_chip->ecc.bytes = 7;
nand_chip->ecc.strength = 4;
nand_chip->ecc.hwctl = omap_enable_hwecc_bch;
nand_chip->ecc.correct = nand_bch_correct_data;
nand_chip->ecc.calculate = omap_calculate_ecc_bch;
/* define ECC layout */
ecclayout->eccbytes = nand_chip->ecc.bytes *
(mtd->writesize /
nand_chip->ecc.size);
oob_index = BADBLOCK_MARKER_LENGTH;
for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) {
ecclayout->eccpos[i] = oob_index;
if (((i + 1) % nand_chip->ecc.bytes) == 0)
oob_index++;
}
/* include reserved-marker in ecclayout->oobfree calculation */
ecclayout->oobfree->offset = 1 +
ecclayout->eccpos[ecclayout->eccbytes - 1] + 1;
/* software bch library is used for locating errors */
nand_chip->ecc.priv = nand_bch_init(mtd,
nand_chip->ecc.size,
nand_chip->ecc.bytes,
&ecclayout);
if (!nand_chip->ecc.priv) {
pr_err("nand: error: unable to use s/w BCH library\n");
err = -EINVAL;
}
break;
#else
pr_err("nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled\n");
err = -EINVAL;
goto return_error;
#endif
case OMAP_ECC_BCH4_CODE_HW:
#ifdef CONFIG_MTD_NAND_OMAP_BCH
pr_info("nand: using OMAP_ECC_BCH4_CODE_HW ECC scheme\n");
nand_chip->ecc.mode = NAND_ECC_HW;
nand_chip->ecc.size = 512;
/* 14th bit is kept reserved for ROM-code compatibility */
nand_chip->ecc.bytes = 7 + 1;
nand_chip->ecc.strength = 4;
nand_chip->ecc.hwctl = omap_enable_hwecc_bch;
nand_chip->ecc.correct = omap_elm_correct_data;
nand_chip->ecc.calculate = omap_calculate_ecc_bch;
nand_chip->ecc.read_page = omap_read_page_bch;
nand_chip->ecc.write_page = omap_write_page_bch;
/* define ECC layout */
ecclayout->eccbytes = nand_chip->ecc.bytes *
(mtd->writesize /
nand_chip->ecc.size);
oob_index = BADBLOCK_MARKER_LENGTH;
for (i = 0; i < ecclayout->eccbytes; i++, oob_index++)
ecclayout->eccpos[i] = oob_index;
/* reserved marker already included in ecclayout->eccbytes */
ecclayout->oobfree->offset =
ecclayout->eccpos[ecclayout->eccbytes - 1] + 1;
/* This ECC scheme requires ELM H/W block */
if (is_elm_present(info, pdata->elm_of_node, BCH4_ECC) < 0) {
pr_err("nand: error: could not initialize ELM\n");
err = -ENODEV;
goto return_error;
}
break;
#else
pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n");
err = -EINVAL;
goto return_error;
#endif
case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
#ifdef CONFIG_MTD_NAND_ECC_BCH
pr_info("nand: using OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n");
nand_chip->ecc.mode = NAND_ECC_HW;
nand_chip->ecc.size = 512;
nand_chip->ecc.bytes = 13;
nand_chip->ecc.strength = 8;
nand_chip->ecc.hwctl = omap_enable_hwecc_bch;
nand_chip->ecc.correct = nand_bch_correct_data;
nand_chip->ecc.calculate = omap_calculate_ecc_bch;
/* define ECC layout */
ecclayout->eccbytes = nand_chip->ecc.bytes *
(mtd->writesize /
nand_chip->ecc.size);
oob_index = BADBLOCK_MARKER_LENGTH;
for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) {
ecclayout->eccpos[i] = oob_index;
if (((i + 1) % nand_chip->ecc.bytes) == 0)
oob_index++;
}
/* include reserved-marker in ecclayout->oobfree calculation */
ecclayout->oobfree->offset = 1 +
ecclayout->eccpos[ecclayout->eccbytes - 1] + 1;
/* software bch library is used for locating errors */
nand_chip->ecc.priv = nand_bch_init(mtd,
nand_chip->ecc.size,
nand_chip->ecc.bytes,
&ecclayout);
if (!nand_chip->ecc.priv) {
pr_err("nand: error: unable to use s/w BCH library\n");
err = -EINVAL;
goto return_error;
}
break;
#else
pr_err("nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled\n");
err = -EINVAL;
goto return_error;
#endif
case OMAP_ECC_BCH8_CODE_HW:
#ifdef CONFIG_MTD_NAND_OMAP_BCH
pr_info("nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme\n");
nand_chip->ecc.mode = NAND_ECC_HW;
nand_chip->ecc.size = 512;
/* 14th bit is kept reserved for ROM-code compatibility */
nand_chip->ecc.bytes = 13 + 1;
nand_chip->ecc.strength = 8;
nand_chip->ecc.hwctl = omap_enable_hwecc_bch;
nand_chip->ecc.correct = omap_elm_correct_data;
nand_chip->ecc.calculate = omap_calculate_ecc_bch;
nand_chip->ecc.read_page = omap_read_page_bch;
nand_chip->ecc.write_page = omap_write_page_bch;
/* This ECC scheme requires ELM H/W block */
err = is_elm_present(info, pdata->elm_of_node, BCH8_ECC);
if (err < 0) {
pr_err("nand: error: could not initialize ELM\n");
goto return_error;
}
/* define ECC layout */
ecclayout->eccbytes = nand_chip->ecc.bytes *
(mtd->writesize /
nand_chip->ecc.size);
oob_index = BADBLOCK_MARKER_LENGTH;
for (i = 0; i < ecclayout->eccbytes; i++, oob_index++)
ecclayout->eccpos[i] = oob_index;
/* reserved marker already included in ecclayout->eccbytes */
ecclayout->oobfree->offset =
ecclayout->eccpos[ecclayout->eccbytes - 1] + 1;
break;
#else
pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n");
err = -EINVAL;
goto return_error;
#endif
case OMAP_ECC_BCH16_CODE_HW:
#ifdef CONFIG_MTD_NAND_OMAP_BCH
pr_info("using OMAP_ECC_BCH16_CODE_HW ECC scheme\n");
nand_chip->ecc.mode = NAND_ECC_HW;
nand_chip->ecc.size = 512;
nand_chip->ecc.bytes = 26;
nand_chip->ecc.strength = 16;
nand_chip->ecc.hwctl = omap_enable_hwecc_bch;
nand_chip->ecc.correct = omap_elm_correct_data;
nand_chip->ecc.calculate = omap_calculate_ecc_bch;
nand_chip->ecc.read_page = omap_read_page_bch;
nand_chip->ecc.write_page = omap_write_page_bch;
/* This ECC scheme requires ELM H/W block */
err = is_elm_present(info, pdata->elm_of_node, BCH16_ECC);
if (err < 0) {
pr_err("ELM is required for this ECC scheme\n");
goto return_error;
}
/* define ECC layout */
ecclayout->eccbytes = nand_chip->ecc.bytes *
(mtd->writesize /
nand_chip->ecc.size);
oob_index = BADBLOCK_MARKER_LENGTH;
for (i = 0; i < ecclayout->eccbytes; i++, oob_index++)
ecclayout->eccpos[i] = oob_index;
/* reserved marker already included in ecclayout->eccbytes */
ecclayout->oobfree->offset =
ecclayout->eccpos[ecclayout->eccbytes - 1] + 1;
break;
#else
pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n");
err = -EINVAL;
goto return_error;
#endif
default:
pr_err("nand: error: invalid or unsupported ECC scheme\n");
err = -EINVAL;
goto return_error;
}
if (info->ecc_opt == OMAP_ECC_HAM1_CODE_SW)
goto scan_tail;
/* all OOB bytes from oobfree->offset till end off OOB are free */
ecclayout->oobfree->length = mtd->oobsize - ecclayout->oobfree->offset;
/* check if NAND device's OOB is enough to store ECC signatures */
if (mtd->oobsize < (ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH)) {
pr_err("not enough OOB bytes required = %d, available=%d\n",
ecclayout->eccbytes, mtd->oobsize);
err = -EINVAL;
goto return_error;
}
nand_chip->ecc.layout = ecclayout;
scan_tail:
/* second phase scan */
if (nand_scan_tail(mtd)) {
err = -ENXIO;
goto return_error;
}
ppdata.of_node = pdata->of_node;
mtd_device_parse_register(mtd, NULL, &ppdata, pdata->parts,
pdata->nr_parts);
platform_set_drvdata(pdev, mtd);
return 0;
return_error:
if (info->dma)
dma_release_channel(info->dma);
if (nand_chip->ecc.priv) {
nand_bch_free(nand_chip->ecc.priv);
nand_chip->ecc.priv = NULL;
}
return err;
}
static int omap_nand_remove(struct platform_device *pdev)
{
struct mtd_info *mtd = platform_get_drvdata(pdev);
struct nand_chip *nand_chip = mtd->priv;
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
if (nand_chip->ecc.priv) {
nand_bch_free(nand_chip->ecc.priv);
nand_chip->ecc.priv = NULL;
}
if (info->dma)
dma_release_channel(info->dma);
nand_release(mtd);
return 0;
}
static struct platform_driver omap_nand_driver = {
.probe = omap_nand_probe,
.remove = omap_nand_remove,
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
},
};
module_platform_driver(omap_nand_driver);
MODULE_ALIAS("platform:" DRIVER_NAME);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Glue layer for NAND flash on TI OMAP boards");
Reference in New Issue View Git Blame Copy Permalink