mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-25 23:30:53 +07:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
86 lines
3.2 KiB
C
86 lines
3.2 KiB
C
#ifndef _PARISC_SUPERIO_H
|
|
#define _PARISC_SUPERIO_H
|
|
|
|
#define IC_PIC1 0x20 /* PCI I/O address of master 8259 */
|
|
#define IC_PIC2 0xA0 /* PCI I/O address of slave */
|
|
|
|
/* Config Space Offsets to configuration and base address registers */
|
|
#define SIO_CR 0x5A /* Configuration Register */
|
|
#define SIO_ACPIBAR 0x88 /* ACPI BAR */
|
|
#define SIO_FDCBAR 0x90 /* Floppy Disk Controller BAR */
|
|
#define SIO_SP1BAR 0x94 /* Serial 1 BAR */
|
|
#define SIO_SP2BAR 0x98 /* Serial 2 BAR */
|
|
#define SIO_PPBAR 0x9C /* Parallel BAR */
|
|
|
|
#define TRIGGER_1 0x67 /* Edge/level trigger register 1 */
|
|
#define TRIGGER_2 0x68 /* Edge/level trigger register 2 */
|
|
|
|
/* Interrupt Routing Control registers */
|
|
#define CFG_IR_SER 0x69 /* Serial 1 [0:3] and Serial 2 [4:7] */
|
|
#define CFG_IR_PFD 0x6a /* Parallel [0:3] and Floppy [4:7] */
|
|
#define CFG_IR_IDE 0x6b /* IDE1 [0:3] and IDE2 [4:7] */
|
|
#define CFG_IR_INTAB 0x6c /* PCI INTA [0:3] and INT B [4:7] */
|
|
#define CFG_IR_INTCD 0x6d /* PCI INTC [0:3] and INT D [4:7] */
|
|
#define CFG_IR_PS2 0x6e /* PS/2 KBINT [0:3] and Mouse [4:7] */
|
|
#define CFG_IR_FXBUS 0x6f /* FXIRQ[0] [0:3] and FXIRQ[1] [4:7] */
|
|
#define CFG_IR_USB 0x70 /* FXIRQ[2] [0:3] and USB [4:7] */
|
|
#define CFG_IR_ACPI 0x71 /* ACPI SCI [0:3] and reserved [4:7] */
|
|
|
|
#define CFG_IR_LOW CFG_IR_SER /* Lowest interrupt routing reg */
|
|
#define CFG_IR_HIGH CFG_IR_ACPI /* Highest interrupt routing reg */
|
|
|
|
/* 8259 operational control words */
|
|
#define OCW2_EOI 0x20 /* Non-specific EOI */
|
|
#define OCW2_SEOI 0x60 /* Specific EOI */
|
|
#define OCW3_IIR 0x0A /* Read request register */
|
|
#define OCW3_ISR 0x0B /* Read service register */
|
|
#define OCW3_POLL 0x0C /* Poll the PIC for an interrupt vector */
|
|
|
|
/* Interrupt lines. Only PIC1 is used */
|
|
#define USB_IRQ 1 /* USB */
|
|
#define SP1_IRQ 3 /* Serial port 1 */
|
|
#define SP2_IRQ 4 /* Serial port 2 */
|
|
#define PAR_IRQ 5 /* Parallel port */
|
|
#define FDC_IRQ 6 /* Floppy controller */
|
|
#define IDE_IRQ 7 /* IDE (pri+sec) */
|
|
|
|
/* ACPI registers */
|
|
#define USB_REG_CR 0x1f /* USB Regulator Control Register */
|
|
|
|
#define SUPERIO_NIRQS 8
|
|
|
|
struct superio_device {
|
|
u32 fdc_base;
|
|
u32 sp1_base;
|
|
u32 sp2_base;
|
|
u32 pp_base;
|
|
u32 acpi_base;
|
|
int suckyio_irq_enabled;
|
|
struct pci_dev *lio_pdev; /* pci device for legacy IO (fn 1) */
|
|
struct pci_dev *usb_pdev; /* pci device for USB (fn 2) */
|
|
};
|
|
|
|
/*
|
|
* Does NS make a 87415 based plug in PCI card? If so, because of this
|
|
* macro we currently don't support it being plugged into a machine
|
|
* that contains a SuperIO chip AND has CONFIG_SUPERIO enabled.
|
|
*
|
|
* This could be fixed by checking to see if function 1 exists, and
|
|
* if it is SuperIO Legacy IO; but really now, is this combination
|
|
* going to EVER happen?
|
|
*/
|
|
|
|
#define SUPERIO_IDE_FN 0 /* Function number of IDE controller */
|
|
#define SUPERIO_LIO_FN 1 /* Function number of Legacy IO controller */
|
|
#define SUPERIO_USB_FN 2 /* Function number of USB controller */
|
|
|
|
#define is_superio_device(x) \
|
|
(((x)->vendor == PCI_VENDOR_ID_NS) && \
|
|
( ((x)->device == PCI_DEVICE_ID_NS_87415) \
|
|
|| ((x)->device == PCI_DEVICE_ID_NS_87560_LIO) \
|
|
|| ((x)->device == PCI_DEVICE_ID_NS_87560_USB) ) )
|
|
|
|
extern int superio_fixup_irq(struct pci_dev *pcidev); /* called by iosapic */
|
|
|
|
#endif /* _PARISC_SUPERIO_H */
|