mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
c50495aa4c
This patch fixes a shared typo in several qcom pinctrl dt-bindings. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org>
85 lines
3.0 KiB
Plaintext
85 lines
3.0 KiB
Plaintext
Qualcomm Atheros IPQ4019 TLMM block
|
|
|
|
This is the Top Level Mode Multiplexor block found on the Qualcomm IPQ8019
|
|
platform, it provides pinctrl, pinmux, pinconf, and gpiolib facilities.
|
|
|
|
Required properties:
|
|
- compatible: "qcom,ipq4019-pinctrl"
|
|
- reg: Should be the base address and length of the TLMM block.
|
|
- interrupts: Should be the parent IRQ of the TLMM block.
|
|
- interrupt-controller: Marks the device node as an interrupt controller.
|
|
- #interrupt-cells: Should be two.
|
|
- gpio-controller: Marks the device node as a GPIO controller.
|
|
- #gpio-cells : Should be two.
|
|
The first cell is the gpio pin number and the
|
|
second cell is used for optional parameters.
|
|
- gpio-ranges: see ../gpio/gpio.txt
|
|
|
|
Optional properties:
|
|
|
|
- gpio-reserved-ranges: see ../gpio/gpio.txt
|
|
|
|
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
|
|
a general description of GPIO and interrupt bindings.
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices, including the meaning of the
|
|
phrase "pin configuration node".
|
|
|
|
The pin configuration nodes act as a container for an abitrary number of
|
|
subnodes. Each of these subnodes represents some desired configuration for a
|
|
pin, a group, or a list of pins or groups. This configuration can include the
|
|
mux function to select on those pin(s)/group(s), and various pin configuration
|
|
parameters, such as pull-up, drive strength, etc.
|
|
|
|
The name of each subnode is not important; all subnodes should be enumerated
|
|
and processed purely based on their content.
|
|
|
|
Each subnode only affects those parameters that are explicitly listed. In
|
|
other words, a subnode that lists a mux function but no pin configuration
|
|
parameters implies no information about any pin configuration parameters.
|
|
Similarly, a pin subnode that describes a pullup parameter implies no
|
|
information about e.g. the mux function.
|
|
|
|
|
|
The following generic properties as defined in pinctrl-bindings.txt are valid
|
|
to specify in a pin configuration subnode:
|
|
pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-strength.
|
|
|
|
Non-empty subnodes must specify the 'pins' property.
|
|
Note that not all properties are valid for all pins.
|
|
|
|
|
|
Valid values for qcom,pins are:
|
|
gpio0-gpio99
|
|
Supports mux, bias and drive-strength
|
|
|
|
Valid values for qcom,function are:
|
|
aud_pin, audio_pwm, blsp_i2c0, blsp_i2c1, blsp_spi0, blsp_spi1, blsp_uart0,
|
|
blsp_uart1, chip_rst, gpio, i2s_rx, i2s_spdif_in, i2s_spdif_out, i2s_td, i2s_tx,
|
|
jtag, led0, led1, led2, led3, led4, led5, led6, led7, led8, led9, led10, led11,
|
|
mdc, mdio, pcie, pmu, prng_rosc, qpic, rgmii, rmii, sdio, smart0, smart1,
|
|
smart2, smart3, tm, wifi0, wifi1
|
|
|
|
Example:
|
|
|
|
tlmm: pinctrl@1000000 {
|
|
compatible = "qcom,ipq4019-pinctrl";
|
|
reg = <0x1000000 0x300000>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-ranges = <&tlmm 0 0 100>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <0 208 0>;
|
|
|
|
serial_pins: serial_pinmux {
|
|
mux {
|
|
pins = "gpio60", "gpio61";
|
|
function = "blsp_uart0";
|
|
bias-disable;
|
|
};
|
|
};
|
|
};
|