mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-25 09:30:53 +07:00
305a99eb98
There are only two files within Documentation/aoe dir that are documentation. The remaining ones are examples and shell scripts. Convert the two AoE files to ReST format, and add the others as literal, as they're part of the documentation. At its new index.rst, let's add a :orphan: while this is not linked to the main index.rst file, in order to avoid build warnings. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
151 lines
5.8 KiB
ReStructuredText
151 lines
5.8 KiB
ReStructuredText
Introduction
|
|
============
|
|
|
|
ATA over Ethernet is a network protocol that provides simple access to
|
|
block storage on the LAN.
|
|
|
|
http://support.coraid.com/documents/AoEr11.txt
|
|
|
|
The EtherDrive (R) HOWTO for 2.6 and 3.x kernels is found at ...
|
|
|
|
http://support.coraid.com/support/linux/EtherDrive-2.6-HOWTO.html
|
|
|
|
It has many tips and hints! Please see, especially, recommended
|
|
tunings for virtual memory:
|
|
|
|
http://support.coraid.com/support/linux/EtherDrive-2.6-HOWTO-5.html#ss5.19
|
|
|
|
The aoetools are userland programs that are designed to work with this
|
|
driver. The aoetools are on sourceforge.
|
|
|
|
http://aoetools.sourceforge.net/
|
|
|
|
The scripts in this Documentation/aoe directory are intended to
|
|
document the use of the driver and are not necessary if you install
|
|
the aoetools.
|
|
|
|
|
|
Creating Device Nodes
|
|
=====================
|
|
|
|
Users of udev should find the block device nodes created
|
|
automatically, but to create all the necessary device nodes, use the
|
|
udev configuration rules provided in udev.txt (in this directory).
|
|
|
|
There is a udev-install.sh script that shows how to install these
|
|
rules on your system.
|
|
|
|
There is also an autoload script that shows how to edit
|
|
/etc/modprobe.d/aoe.conf to ensure that the aoe module is loaded when
|
|
necessary. Preloading the aoe module is preferable to autoloading,
|
|
however, because AoE discovery takes a few seconds. It can be
|
|
confusing when an AoE device is not present the first time the a
|
|
command is run but appears a second later.
|
|
|
|
Using Device Nodes
|
|
==================
|
|
|
|
"cat /dev/etherd/err" blocks, waiting for error diagnostic output,
|
|
like any retransmitted packets.
|
|
|
|
"echo eth2 eth4 > /dev/etherd/interfaces" tells the aoe driver to
|
|
limit ATA over Ethernet traffic to eth2 and eth4. AoE traffic from
|
|
untrusted networks should be ignored as a matter of security. See
|
|
also the aoe_iflist driver option described below.
|
|
|
|
"echo > /dev/etherd/discover" tells the driver to find out what AoE
|
|
devices are available.
|
|
|
|
In the future these character devices may disappear and be replaced
|
|
by sysfs counterparts. Using the commands in aoetools insulates
|
|
users from these implementation details.
|
|
|
|
The block devices are named like this::
|
|
|
|
e{shelf}.{slot}
|
|
e{shelf}.{slot}p{part}
|
|
|
|
... so that "e0.2" is the third blade from the left (slot 2) in the
|
|
first shelf (shelf address zero). That's the whole disk. The first
|
|
partition on that disk would be "e0.2p1".
|
|
|
|
Using sysfs
|
|
===========
|
|
|
|
Each aoe block device in /sys/block has the extra attributes of
|
|
state, mac, and netif. The state attribute is "up" when the device
|
|
is ready for I/O and "down" if detected but unusable. The
|
|
"down,closewait" state shows that the device is still open and
|
|
cannot come up again until it has been closed.
|
|
|
|
The mac attribute is the ethernet address of the remote AoE device.
|
|
The netif attribute is the network interface on the localhost
|
|
through which we are communicating with the remote AoE device.
|
|
|
|
There is a script in this directory that formats this information in
|
|
a convenient way. Users with aoetools should use the aoe-stat
|
|
command::
|
|
|
|
root@makki root# sh Documentation/aoe/status.sh
|
|
e10.0 eth3 up
|
|
e10.1 eth3 up
|
|
e10.2 eth3 up
|
|
e10.3 eth3 up
|
|
e10.4 eth3 up
|
|
e10.5 eth3 up
|
|
e10.6 eth3 up
|
|
e10.7 eth3 up
|
|
e10.8 eth3 up
|
|
e10.9 eth3 up
|
|
e4.0 eth1 up
|
|
e4.1 eth1 up
|
|
e4.2 eth1 up
|
|
e4.3 eth1 up
|
|
e4.4 eth1 up
|
|
e4.5 eth1 up
|
|
e4.6 eth1 up
|
|
e4.7 eth1 up
|
|
e4.8 eth1 up
|
|
e4.9 eth1 up
|
|
|
|
Use /sys/module/aoe/parameters/aoe_iflist (or better, the driver
|
|
option discussed below) instead of /dev/etherd/interfaces to limit
|
|
AoE traffic to the network interfaces in the given
|
|
whitespace-separated list. Unlike the old character device, the
|
|
sysfs entry can be read from as well as written to.
|
|
|
|
It's helpful to trigger discovery after setting the list of allowed
|
|
interfaces. The aoetools package provides an aoe-discover script
|
|
for this purpose. You can also directly use the
|
|
/dev/etherd/discover special file described above.
|
|
|
|
Driver Options
|
|
==============
|
|
|
|
There is a boot option for the built-in aoe driver and a
|
|
corresponding module parameter, aoe_iflist. Without this option,
|
|
all network interfaces may be used for ATA over Ethernet. Here is a
|
|
usage example for the module parameter::
|
|
|
|
modprobe aoe_iflist="eth1 eth3"
|
|
|
|
The aoe_deadsecs module parameter determines the maximum number of
|
|
seconds that the driver will wait for an AoE device to provide a
|
|
response to an AoE command. After aoe_deadsecs seconds have
|
|
elapsed, the AoE device will be marked as "down". A value of zero
|
|
is supported for testing purposes and makes the aoe driver keep
|
|
trying AoE commands forever.
|
|
|
|
The aoe_maxout module parameter has a default of 128. This is the
|
|
maximum number of unresponded packets that will be sent to an AoE
|
|
target at one time.
|
|
|
|
The aoe_dyndevs module parameter defaults to 1, meaning that the
|
|
driver will assign a block device minor number to a discovered AoE
|
|
target based on the order of its discovery. With dynamic minor
|
|
device numbers in use, a greater range of AoE shelf and slot
|
|
addresses can be supported. Users with udev will never have to
|
|
think about minor numbers. Using aoe_dyndevs=0 allows device nodes
|
|
to be pre-created using a static minor-number scheme with the
|
|
aoe-mkshelf script in the aoetools.
|