AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-15 08:46:45 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
6b667f880f
linux_dsm_epyc7002/arch/arm/mach-omap2/board-omap3evm.c
Sukumar Ghorai 3a63833ec3 omap: mmc: extended to pass host capabilities from board file 
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-09-27 10:15:26 -07:00

727 lines
18 KiB
C
Raw Blame History

/*
* linux/arch/arm/mach-omap2/board-omap3evm.c
*
* Copyright (C) 2008 Texas Instruments
*
* Modified from mach-omap2/board-3430sdp.c
*
* Initial code: Syed Mohammed Khasim
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/input/matrix_keypad.h>
#include <linux/leds.h>
#include <linux/interrupt.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/i2c/twl.h>
#include <linux/usb/otg.h>
#include <linux/smsc911x.h>
#include <linux/regulator/machine.h>
#include <linux/mmc/host.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <plat/board.h>
#include <plat/usb.h>
#include <plat/common.h>
#include <plat/mcspi.h>
#include <plat/display.h>
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
#define OMAP3_EVM_TS_GPIO 175
#define OMAP3_EVM_EHCI_VBUS 22
#define OMAP3_EVM_EHCI_SELECT 61
#define OMAP3EVM_ETHR_START 0x2c000000
#define OMAP3EVM_ETHR_SIZE 1024
#define OMAP3EVM_ETHR_ID_REV 0x50
#define OMAP3EVM_ETHR_GPIO_IRQ 176
#define OMAP3EVM_SMSC911X_CS 5
static u8 omap3_evm_version;
u8 get_omap3_evm_rev(void)
{
return omap3_evm_version;
}
EXPORT_SYMBOL(get_omap3_evm_rev);
static void __init omap3_evm_get_revision(void)
{
void __iomem *ioaddr;
unsigned int smsc_id;
/* Ethernet PHY ID is stored at ID_REV register */
ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K);
if (!ioaddr)
return;
smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000;
iounmap(ioaddr);
switch (smsc_id) {
/*SMSC9115 chipset*/
case 0x01150000:
omap3_evm_version = OMAP3EVM_BOARD_GEN_1;
break;
/*SMSC 9220 chipset*/
case 0x92200000:
default:
omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
}
}
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
static struct resource omap3evm_smsc911x_resources[] = {
[0] = {
.start = OMAP3EVM_ETHR_START,
.end = (OMAP3EVM_ETHR_START + OMAP3EVM_ETHR_SIZE - 1),
.flags = IORESOURCE_MEM,
},
[1] = {
.start = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ),
.end = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ),
.flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW),
},
};
static struct smsc911x_platform_config smsc911x_config = {
.phy_interface = PHY_INTERFACE_MODE_MII,
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
.flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
};
static struct platform_device omap3evm_smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(omap3evm_smsc911x_resources),
.resource = &omap3evm_smsc911x_resources[0],
.dev = {
.platform_data = &smsc911x_config,
},
};
static inline void __init omap3evm_init_smsc911x(void)
{
int eth_cs;
struct clk *l3ck;
unsigned int rate;
eth_cs = OMAP3EVM_SMSC911X_CS;
l3ck = clk_get(NULL, "l3_ck");
if (IS_ERR(l3ck))
rate = 100000000;
else
rate = clk_get_rate(l3ck);
if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
OMAP3EVM_ETHR_GPIO_IRQ);
return;
}
gpio_direction_input(OMAP3EVM_ETHR_GPIO_IRQ);
platform_device_register(&omap3evm_smsc911x_device);
}
#else
static inline void __init omap3evm_init_smsc911x(void) { return; }
#endif
/*
* OMAP3EVM LCD Panel control signals
*/
#define OMAP3EVM_LCD_PANEL_LR 2
#define OMAP3EVM_LCD_PANEL_UD 3
#define OMAP3EVM_LCD_PANEL_INI 152
#define OMAP3EVM_LCD_PANEL_ENVDD 153
#define OMAP3EVM_LCD_PANEL_QVGA 154
#define OMAP3EVM_LCD_PANEL_RESB 155
#define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210
#define OMAP3EVM_DVI_PANEL_EN_GPIO 199
static int lcd_enabled;
static int dvi_enabled;
static void __init omap3_evm_display_init(void)
{
int r;
r = gpio_request(OMAP3EVM_LCD_PANEL_RESB, "lcd_panel_resb");
if (r) {
printk(KERN_ERR "failed to get lcd_panel_resb\n");
return;
}
gpio_direction_output(OMAP3EVM_LCD_PANEL_RESB, 1);
r = gpio_request(OMAP3EVM_LCD_PANEL_INI, "lcd_panel_ini");
if (r) {
printk(KERN_ERR "failed to get lcd_panel_ini\n");
goto err_1;
}
gpio_direction_output(OMAP3EVM_LCD_PANEL_INI, 1);
r = gpio_request(OMAP3EVM_LCD_PANEL_QVGA, "lcd_panel_qvga");
if (r) {
printk(KERN_ERR "failed to get lcd_panel_qvga\n");
goto err_2;
}
gpio_direction_output(OMAP3EVM_LCD_PANEL_QVGA, 0);
r = gpio_request(OMAP3EVM_LCD_PANEL_LR, "lcd_panel_lr");
if (r) {
printk(KERN_ERR "failed to get lcd_panel_lr\n");
goto err_3;
}
gpio_direction_output(OMAP3EVM_LCD_PANEL_LR, 1);
r = gpio_request(OMAP3EVM_LCD_PANEL_UD, "lcd_panel_ud");
if (r) {
printk(KERN_ERR "failed to get lcd_panel_ud\n");
goto err_4;
}
gpio_direction_output(OMAP3EVM_LCD_PANEL_UD, 1);
r = gpio_request(OMAP3EVM_LCD_PANEL_ENVDD, "lcd_panel_envdd");
if (r) {
printk(KERN_ERR "failed to get lcd_panel_envdd\n");
goto err_5;
}
gpio_direction_output(OMAP3EVM_LCD_PANEL_ENVDD, 0);
return;
err_5:
gpio_free(OMAP3EVM_LCD_PANEL_UD);
err_4:
gpio_free(OMAP3EVM_LCD_PANEL_LR);
err_3:
gpio_free(OMAP3EVM_LCD_PANEL_QVGA);
err_2:
gpio_free(OMAP3EVM_LCD_PANEL_INI);
err_1:
gpio_free(OMAP3EVM_LCD_PANEL_RESB);
}
static int omap3_evm_enable_lcd(struct omap_dss_device *dssdev)
{
if (dvi_enabled) {
printk(KERN_ERR "cannot enable LCD, DVI is enabled\n");
return -EINVAL;
}
gpio_set_value(OMAP3EVM_LCD_PANEL_ENVDD, 0);
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
gpio_set_value(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0);
else
gpio_set_value(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1);
lcd_enabled = 1;
return 0;
}
static void omap3_evm_disable_lcd(struct omap_dss_device *dssdev)
{
gpio_set_value(OMAP3EVM_LCD_PANEL_ENVDD, 1);
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
gpio_set_value(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1);
else
gpio_set_value(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0);
lcd_enabled = 0;
}
static struct omap_dss_device omap3_evm_lcd_device = {
.name = "lcd",
.driver_name = "sharp_ls_panel",
.type = OMAP_DISPLAY_TYPE_DPI,
.phy.dpi.data_lines = 18,
.platform_enable = omap3_evm_enable_lcd,
.platform_disable = omap3_evm_disable_lcd,
};
static int omap3_evm_enable_tv(struct omap_dss_device *dssdev)
{
return 0;
}
static void omap3_evm_disable_tv(struct omap_dss_device *dssdev)
{
}
static struct omap_dss_device omap3_evm_tv_device = {
.name = "tv",
.driver_name = "venc",
.type = OMAP_DISPLAY_TYPE_VENC,
.phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
.platform_enable = omap3_evm_enable_tv,
.platform_disable = omap3_evm_disable_tv,
};
static int omap3_evm_enable_dvi(struct omap_dss_device *dssdev)
{
if (lcd_enabled) {
printk(KERN_ERR "cannot enable DVI, LCD is enabled\n");
return -EINVAL;
}
gpio_set_value(OMAP3EVM_DVI_PANEL_EN_GPIO, 1);
dvi_enabled = 1;
return 0;
}
static void omap3_evm_disable_dvi(struct omap_dss_device *dssdev)
{
gpio_set_value(OMAP3EVM_DVI_PANEL_EN_GPIO, 0);
dvi_enabled = 0;
}
static struct omap_dss_device omap3_evm_dvi_device = {
.name = "dvi",
.driver_name = "generic_panel",
.type = OMAP_DISPLAY_TYPE_DPI,
.phy.dpi.data_lines = 24,
.platform_enable = omap3_evm_enable_dvi,
.platform_disable = omap3_evm_disable_dvi,
};
static struct omap_dss_device *omap3_evm_dss_devices[] = {
&omap3_evm_lcd_device,
&omap3_evm_tv_device,
&omap3_evm_dvi_device,
};
static struct omap_dss_board_info omap3_evm_dss_data = {
.num_devices = ARRAY_SIZE(omap3_evm_dss_devices),
.devices = omap3_evm_dss_devices,
.default_device = &omap3_evm_lcd_device,
};
static struct platform_device omap3_evm_dss_device = {
.name = "omapdss",
.id = -1,
.dev = {
.platform_data = &omap3_evm_dss_data,
},
};
static struct regulator_consumer_supply omap3evm_vmmc1_supply = {
.supply = "vmmc",
};
static struct regulator_consumer_supply omap3evm_vsim_supply = {
.supply = "vmmc_aux",
};
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data omap3evm_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
.consumer_supplies = &omap3evm_vmmc1_supply,
};
/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
static struct regulator_init_data omap3evm_vsim = {
.constraints = {
.min_uV = 1800000,
.max_uV = 3000000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
.consumer_supplies = &omap3evm_vsim_supply,
};
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_cd = -EINVAL,
.gpio_wp = 63,
},
{} /* Terminator */
};
static struct gpio_led gpio_leds[] = {
{
.name = "omap3evm::ledb",
/* normally not visible (board underside) */
.default_trigger = "default-on",
.gpio = -EINVAL, /* gets replaced */
.active_low = true,
},
};
static struct gpio_led_platform_data gpio_led_info = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct platform_device leds_gpio = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &gpio_led_info,
},
};
static int omap3evm_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
omap_mux_init_gpio(63, OMAP_PIN_INPUT);
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
/* link regulators to MMC adapters */
omap3evm_vmmc1_supply.dev = mmc[0].dev;
omap3evm_vsim_supply.dev = mmc[0].dev;
/*
* Most GPIOs are for USB OTG. Some are mostly sent to
* the P2 connector; notably LEDA for the LCD backlight.
*/
/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL");
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
/* gpio + 7 == DVI Enable */
gpio_request(gpio + 7, "EN_DVI");
gpio_direction_output(gpio + 7, 0);
/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
platform_device_register(&leds_gpio);
return 0;
}
static struct twl4030_gpio_platform_data omap3evm_gpio_data = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
.irq_end = TWL4030_GPIO_IRQ_END,
.use_leds = true,
.setup = omap3evm_twl_gpio_setup,
};
static struct twl4030_usb_data omap3evm_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
static int board_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_DOWN),
KEY(0, 2, KEY_ENTER),
KEY(0, 3, KEY_M),
KEY(1, 0, KEY_RIGHT),
KEY(1, 1, KEY_UP),
KEY(1, 2, KEY_I),
KEY(1, 3, KEY_N),
KEY(2, 0, KEY_A),
KEY(2, 1, KEY_E),
KEY(2, 2, KEY_J),
KEY(2, 3, KEY_O),
KEY(3, 0, KEY_B),
KEY(3, 1, KEY_F),
KEY(3, 2, KEY_K),
KEY(3, 3, KEY_P)
};
static struct matrix_keymap_data board_map_data = {
.keymap = board_keymap,
.keymap_size = ARRAY_SIZE(board_keymap),
};
static struct twl4030_keypad_data omap3evm_kp_data = {
.keymap_data = &board_map_data,
.rows = 4,
.cols = 4,
.rep = 1,
};
static struct twl4030_madc_platform_data omap3evm_madc_data = {
.irq_line = 1,
};
static struct twl4030_codec_audio_data omap3evm_audio_data = {
.audio_mclk = 26000000,
};
static struct twl4030_codec_data omap3evm_codec_data = {
.audio_mclk = 26000000,
.audio = &omap3evm_audio_data,
};
static struct regulator_consumer_supply omap3_evm_vdda_dac_supply = {
.supply = "vdda_dac",
.dev = &omap3_evm_dss_device.dev,
};
/* VDAC for DSS driving S-Video */
static struct regulator_init_data omap3_evm_vdac = {
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
.apply_uV = true,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
.consumer_supplies = &omap3_evm_vdda_dac_supply,
};
/* VPLL2 for digital video outputs */
static struct regulator_consumer_supply omap3_evm_vpll2_supply =
REGULATOR_SUPPLY("vdds_dsi", "omapdss");
static struct regulator_init_data omap3_evm_vpll2 = {
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
.apply_uV = true,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
.consumer_supplies = &omap3_evm_vpll2_supply,
};
static struct twl4030_platform_data omap3evm_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
.keypad = &omap3evm_kp_data,
.madc = &omap3evm_madc_data,
.usb = &omap3evm_usb_data,
.gpio = &omap3evm_gpio_data,
.codec = &omap3evm_codec_data,
.vdac = &omap3_evm_vdac,
.vpll2 = &omap3_evm_vpll2,
};
static struct i2c_board_info __initdata omap3evm_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &omap3evm_twldata,
},
};
static int __init omap3_evm_i2c_init(void)
{
/*
* REVISIT: These entries can be set in omap3evm_twl_data
* after a merge with MFD tree
*/
omap3evm_twldata.vmmc1 = &omap3evm_vmmc1;
omap3evm_twldata.vsim = &omap3evm_vsim;
omap_register_i2c_bus(1, 2600, omap3evm_i2c_boardinfo,
ARRAY_SIZE(omap3evm_i2c_boardinfo));
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
static void ads7846_dev_init(void)
{
if (gpio_request(OMAP3_EVM_TS_GPIO, "ADS7846 pendown") < 0)
printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
gpio_direction_input(OMAP3_EVM_TS_GPIO);
gpio_set_debounce(OMAP3_EVM_TS_GPIO, 310);
}
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(OMAP3_EVM_TS_GPIO);
}
struct ads7846_platform_data ads7846_config = {
.x_max = 0x0fff,
.y_max = 0x0fff,
.x_plate_ohms = 180,
.pressure_max = 255,
.debounce_max = 10,
.debounce_tol = 3,
.debounce_rep = 1,
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
.settle_delay_usecs = 150,
.wakeup = true,
};
static struct omap2_mcspi_device_config ads7846_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
struct spi_board_info omap3evm_spi_board_info[] = {
[0] = {
.modalias = "ads7846",
.bus_num = 1,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(OMAP3_EVM_TS_GPIO),
.platform_data = &ads7846_config,
},
};
static struct omap_board_config_kernel omap3_evm_config[] __initdata = {
};
static void __init omap3_evm_init_irq(void)
{
omap_board_config = omap3_evm_config;
omap_board_config_size = ARRAY_SIZE(omap3_evm_config);
omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL);
omap_init_irq();
omap_gpio_init();
}
static struct platform_device *omap3_evm_devices[] __initdata = {
&omap3_evm_dss_device,
};
static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
.port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
.phy_reset = true,
/* PHY reset GPIO will be runtime programmed based on EVM version */
.reset_gpio_port[0] = -EINVAL,
.reset_gpio_port[1] = -EINVAL,
.reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
OMAP_PIN_OFF_WAKEUPENABLE),
OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
#define board_mux NULL
#endif
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static void __init omap3_evm_init(void)
{
omap3_evm_get_revision();
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_evm_i2c_init();
platform_add_devices(omap3_evm_devices, ARRAY_SIZE(omap3_evm_devices));
spi_register_board_info(omap3evm_spi_board_info,
ARRAY_SIZE(omap3evm_spi_board_info));
omap_serial_init();
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
usb_nop_xceiv_register();
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
/* enable EHCI VBUS using GPIO22 */
omap_mux_init_gpio(22, OMAP_PIN_INPUT_PULLUP);
gpio_request(OMAP3_EVM_EHCI_VBUS, "enable EHCI VBUS");
gpio_direction_output(OMAP3_EVM_EHCI_VBUS, 0);
gpio_set_value(OMAP3_EVM_EHCI_VBUS, 1);
/* Select EHCI port on main board */
omap_mux_init_gpio(61, OMAP_PIN_INPUT_PULLUP);
gpio_request(OMAP3_EVM_EHCI_SELECT, "select EHCI port");
gpio_direction_output(OMAP3_EVM_EHCI_SELECT, 0);
gpio_set_value(OMAP3_EVM_EHCI_SELECT, 0);
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
ehci_pdata.reset_gpio_port[1] = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
musb_board_data.extvbus = 1;
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
ehci_pdata.reset_gpio_port[1] = 135;
}
usb_musb_init(&musb_board_data);
usb_ehci_init(&ehci_pdata);
ads7846_dev_init();
omap3evm_init_smsc911x();
omap3_evm_display_init();
}
MACHINE_START(OMAP3EVM, "OMAP3 EVM")
/* Maintainer: Syed Mohammed Khasim - Texas Instruments */
.phys_io = 0x48000000,
.io_pg_offst = ((0xfa000000) >> 18) & 0xfffc,
.boot_params = 0x80000100,
.map_io = omap3_map_io,
.reserve = omap_reserve,
.init_irq = omap3_evm_init_irq,
.init_machine = omap3_evm_init,
.timer = &omap_timer,
MACHINE_END
Reference in New Issue View Git Blame Copy Permalink