mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
6b08c3854c
If a hotplug port is able to send an interrupt, one would naively assume that it is accessible at that moment. After all, if it wouldn't be accessible, i.e. if its parent is in D3hot and the link to the hotplug port is thus down, how should an interrupt come through? It turns out that assumption is wrong at least for Thunderbolt: Even though its parents are in D3hot, a Thunderbolt hotplug port is able to signal interrupts. Because the port's config space is inaccessible and resuming the parents may sleep, the hard IRQ handler has to defer runtime resuming the parents and reading the Slot Status register to the IRQ thread. If the hotplug port uses a level-triggered INTx interrupt, it needs to be masked until the IRQ thread has cleared the signaled events. For simplicity, this commit also masks edge-triggered MSI/MSI-X interrupts. Note that if the interrupt is shared (which can only happen for INTx), other devices are starved from receiving interrupts until the IRQ thread is scheduled, has runtime resumed the hotplug port's parents and has read and cleared the Slot Status register. That delay is dominated by the 10 ms D3hot->D0 transition time of each parent port. The worst case is a Thunderbolt downstream port at the end of a daisy chain: There may be up to six Thunderbolt controllers in-between it and the root port, each comprising an upstream and downstream port, plus its own upstream port. That's 13 x 10 = 130 ms. Possible mitigations are polling the interrupt while it's disabled or reducing the d3_delay of Thunderbolt ports if possible. Open code masking of the interrupt instead of requesting it with the IRQF_ONESHOT flag to minimize the period during which it is masked. (IRQF_ONESHOT unmasks the IRQ only after the IRQ thread has finished.) PCIe r4.0 sec 6.7.3.4 states that "If wake generation is required by the associated form factor specification, a hotplug capable Downstream Port must support generation of a wakeup event (using the PME mechanism) on hotplug events that occur when the system is in a sleep state or the Port is in device state D1, D2, or D3Hot." This would seem to imply that PME needs to be enabled on the hotplug port when it is runtime suspended. pci_enable_wake() currently doesn't enable PME on bridges, it may be necessary to add an exemption for hotplug bridges there. On "Light Ridge" Thunderbolt controllers, the PME_Status bit is not set when an interrupt occurs while the hotplug port is in D3hot, even if PME is enabled. (I've tested this on a Mac and we hardcode the OSC_PCI_EXPRESS_PME_CONTROL bit to 0 on Macs in negotiate_os_control(), modifying it to 1 didn't change the behavior.) (Side note: Section 6.7.3.4 also states that "PME and Hot-Plug Event interrupts (when both are implemented) always share the same MSI or MSI-X vector". That would only seem to apply to Root Ports, however the section never mentions Root Ports, only Downstream Ports. This is explained in the definition of "Downstream Port" in the "Terms and Acronyms" section of the PCIe Base Spec: "The Ports on a Switch that are not the Upstream Port are Downstream Ports. All Ports on a Root Complex are Downstream Ports.") Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Ashok Raj <ashok.raj@intel.com> Cc: Keith Busch <keith.busch@intel.com> Cc: Yinghai Lu <yinghai@kernel.org> |
||
|---|---|---|
| .. | ||
| accessibility | ||
| acpi | ||
| amba | ||
| android | ||
| ata | ||
| atm | ||
| auxdisplay | ||
| base | ||
| bcma | ||
| block | ||
| bluetooth | ||
| bus | ||
| cdrom | ||
| char | ||
| clk | ||
| clocksource | ||
| connector | ||
| cpufreq | ||
| cpuidle | ||
| crypto | ||
| dax | ||
| dca | ||
| devfreq | ||
| dio | ||
| dma | ||
| dma-buf | ||
| edac | ||
| eisa | ||
| extcon | ||
| firewire | ||
| firmware | ||
| fmc | ||
| fpga | ||
| fsi | ||
| gpio | ||
| gpu | ||
| hid | ||
| hsi | ||
| hv | ||
| hwmon | ||
| hwspinlock | ||
| hwtracing | ||
| i2c | ||
| ide | ||
| idle | ||
| iio | ||
| infiniband | ||
| input | ||
| iommu | ||
| ipack | ||
| irqchip | ||
| isdn | ||
| leds | ||
| lightnvm | ||
| macintosh | ||
| mailbox | ||
| mcb | ||
| md | ||
| media | ||
| memory | ||
| memstick | ||
| message | ||
| mfd | ||
| misc | ||
| mmc | ||
| mtd | ||
| mux | ||
| net | ||
| nfc | ||
| ntb | ||
| nubus | ||
| nvdimm | ||
| nvme | ||
| nvmem | ||
| of | ||
| opp | ||
| oprofile | ||
| parisc | ||
| parport | ||
| pci | ||
| pcmcia | ||
| perf | ||
| phy | ||
| pinctrl | ||
| platform | ||
| pnp | ||
| power | ||
| powercap | ||
| pps | ||
| ps3 | ||
| ptp | ||
| pwm | ||
| rapidio | ||
| ras | ||
| regulator | ||
| remoteproc | ||
| reset | ||
| rpmsg | ||
| rtc | ||
| s390 | ||
| sbus | ||
| scsi | ||
| sfi | ||
| sh | ||
| siox | ||
| slimbus | ||
| sn | ||
| soc | ||
| soundwire | ||
| spi | ||
| spmi | ||
| ssb | ||
| staging | ||
| target | ||
| tc | ||
| tee | ||
| thermal | ||
| thunderbolt | ||
| tty | ||
| uio | ||
| usb | ||
| uwb | ||
| vfio | ||
| vhost | ||
| video | ||
| virt | ||
| virtio | ||
| visorbus | ||
| vlynq | ||
| vme | ||
| w1 | ||
| watchdog | ||
| xen | ||
| zorro | ||
| Kconfig | ||
| Makefile | ||