mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-21 08:46:49 +07:00
8c059a4676
Update documentation for gpio-cs and num-cs to reflect the standard SPI bindings. The dma properties are optional. Include a warning that native CS do not work in a commonly useful manner with this hardware/driver, and therefor most users probably should use GPIO based CS lines rather than native. CC: Mark Brown <broonie@kernel.org> CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <kernel@pengutronix.de> CC: Fabio Estevam <fabio.estevam@nxp.com> CC: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Signed-off-by: Mark Brown <broonie@kernel.org>
53 lines
2.2 KiB
Plaintext
53 lines
2.2 KiB
Plaintext
* Freescale (Enhanced) Configurable Serial Peripheral Interface
|
|
(CSPI/eCSPI) for i.MX
|
|
|
|
Required properties:
|
|
- compatible :
|
|
- "fsl,imx1-cspi" for SPI compatible with the one integrated on i.MX1
|
|
- "fsl,imx21-cspi" for SPI compatible with the one integrated on i.MX21
|
|
- "fsl,imx27-cspi" for SPI compatible with the one integrated on i.MX27
|
|
- "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31
|
|
- "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35
|
|
- "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51
|
|
- "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc
|
|
- reg : Offset and length of the register set for the device
|
|
- interrupts : Should contain CSPI/eCSPI interrupt
|
|
- clocks : Clock specifiers for both ipg and per clocks.
|
|
- clock-names : Clock names should include both "ipg" and "per"
|
|
See the clock consumer binding,
|
|
Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
|
|
Recommended properties:
|
|
- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip
|
|
select lines can be used, they appear to always generate a pulse between each
|
|
word of a transfer. Most use cases will require GPIO based chip selects to
|
|
generate a valid transaction.
|
|
|
|
Optional properties:
|
|
- num-cs : Number of total chip selects, see spi-bus.txt.
|
|
- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
|
|
Documentation/devicetree/bindings/dma/dma.txt.
|
|
- dma-names: DMA request names, if present, should include "tx" and "rx".
|
|
- fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register
|
|
controlling the SPI_READY handling. Note that to enable the DRCTL consideration,
|
|
the SPI_READY mode-flag needs to be set too.
|
|
Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst).
|
|
|
|
Obsolete properties:
|
|
- fsl,spi-num-chipselects : Contains the number of the chipselect
|
|
|
|
Example:
|
|
|
|
ecspi@70010000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,imx51-ecspi";
|
|
reg = <0x70010000 0x4000>;
|
|
interrupts = <36>;
|
|
cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */
|
|
<&gpio3 25 0>; /* GPIO3_25 */
|
|
dmas = <&sdma 3 7 1>, <&sdma 4 7 2>;
|
|
dma-names = "rx", "tx";
|
|
fsl,spi-rdy-drctl = <1>;
|
|
};
|