linux_dsm_epyc7002/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
Fabrice Gasnier 5254582395 ARM: dts: stm32: add PWM pins used on stm32mp157c-ev1 board
stm32mp157c evaluation board has following PWM pins available on GPIO
expansion connector:
- TIM2_CH4 (PA3)
- TIM8_CH4 (PI2)
- TIM12_CH1 (PH6)

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-05-02 17:18:57 +02:00

213 lines
4.6 KiB
Plaintext

// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
*/
#include <dt-bindings/pinctrl/stm32-pinfunc.h>
/ {
soc {
pinctrl: pin-controller {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,stm32mp157-pinctrl";
ranges = <0 0x50002000 0xa400>;
pins-are-numbered;
gpioa: gpio@50002000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x0 0x400>;
clocks = <&rcc GPIOA>;
st,bank-name = "GPIOA";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 0 16>;
};
gpiob: gpio@50003000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x400>;
clocks = <&rcc GPIOB>;
st,bank-name = "GPIOB";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 16 16>;
};
gpioc: gpio@50004000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x400>;
clocks = <&rcc GPIOC>;
st,bank-name = "GPIOC";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 32 16>;
};
gpiod: gpio@50005000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x400>;
clocks = <&rcc GPIOD>;
st,bank-name = "GPIOD";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 48 16>;
};
gpioe: gpio@50006000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x400>;
clocks = <&rcc GPIOE>;
st,bank-name = "GPIOE";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 64 16>;
};
gpiof: gpio@50007000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000 0x400>;
clocks = <&rcc GPIOF>;
st,bank-name = "GPIOF";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 80 16>;
};
gpiog: gpio@50008000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x6000 0x400>;
clocks = <&rcc GPIOG>;
st,bank-name = "GPIOG";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 96 16>;
};
gpioh: gpio@50009000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x7000 0x400>;
clocks = <&rcc GPIOH>;
st,bank-name = "GPIOH";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 112 16>;
};
gpioi: gpio@5000a000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x8000 0x400>;
clocks = <&rcc GPIOI>;
st,bank-name = "GPIOI";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 128 16>;
};
gpioj: gpio@5000b000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x9000 0x400>;
clocks = <&rcc GPIOJ>;
st,bank-name = "GPIOJ";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 144 16>;
};
gpiok: gpio@5000c000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0xa000 0x400>;
clocks = <&rcc GPIOK>;
st,bank-name = "GPIOK";
ngpios = <8>;
gpio-ranges = <&pinctrl 0 160 8>;
};
pwm2_pins_a: pwm2-0 {
pins {
pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
bias-pull-down;
drive-push-pull;
slew-rate = <0>;
};
};
pwm8_pins_a: pwm8-0 {
pins {
pinmux = <STM32_PINMUX('I', 2, AF3)>; /* TIM8_CH4 */
bias-pull-down;
drive-push-pull;
slew-rate = <0>;
};
};
pwm12_pins_a: pwm12-0 {
pins {
pinmux = <STM32_PINMUX('H', 6, AF2)>; /* TIM12_CH1 */
bias-pull-down;
drive-push-pull;
slew-rate = <0>;
};
};
uart4_pins_a: uart4@0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
bias-disable;
drive-push-pull;
slew-rate = <0>;
};
pins2 {
pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
bias-disable;
};
};
};
pinctrl_z: pin-controller-z {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,stm32mp157-z-pinctrl";
ranges = <0 0x54004000 0x400>;
pins-are-numbered;
status = "disabled";
gpioz: gpio@54004000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x400>;
clocks = <&rcc GPIOZ>;
st,bank-name = "GPIOZ";
st,bank-ioport = <11>;
ngpios = <8>;
gpio-ranges = <&pinctrl_z 0 400 8>;
};
};
};
};