mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-26 11:30:54 +07:00
43c95d3694
cycle: Core changes: - Device links can optionally be added between a pin control producer and its consumers. This will affect how the system power management is handled: a pin controller will not suspend before all of its consumers have been suspended. This was necessary for the ST Microelectronics STMFX expander and need to be tested on other systems as well: it makes sense to make this default in the long run. Right now it is opt-in per driver. - Drive strength can be specified in microamps. With decreases in silicon technology, milliamps isn't granular enough, let's make it possible to select drive strengths in microamps. Right now the Meson (AMlogic) driver needs this. New drivers: - New subdriver for the Tegra 194 SoC. - New subdriver for the Qualcomm SDM845. - New subdriver for the Qualcomm SM8150. - New subdriver for the Freescale i.MX8MN (Freescale is now a product line of NXP). - New subdriver for Marvell MV98DX1135. Driver improvements: - The Bitmain BM1880 driver now supports pin config in addition to muxing. - The Qualcomm drivers can now reserve some GPIOs as taken aside and not usable for users. This is used in ACPI systems to take out some GPIO lines used by the BIOS so that noone else (neither kernel nor userspace) will play with them by mistake and crash the machine. - A slew of refurbishing around the Aspeed drivers (board management controllers for servers) in preparation for the new Aspeed AST2600 SoC. - A slew of improvements over the SH PFC drivers as usual. - Misc cleanups and fixes. -----BEGIN PGP SIGNATURE----- iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl0oTPcACgkQQRCzN7AZ XXNTsw//aNPfkJS8gRszv58G56lyuO8h6Cq4m5eDpzhlpjx5qjELgi9h2UNGINqD 7CWxo35ufbKe0fDIcqpXmtuDMtSu6MuKT3SMepuw9uf9wxyndK4RIuyb0lpAJrx2 +NMPxzS+ARlrMmcfvXPRyPWHqAkXsQk6zcCgiuNCPtROkOZgs1YZ3+pemZw2/FMq gSLTO/95p0TPWr6YAlpByqfsA1A/onEm9HOiU2INV7DrAfUj7mnkuC1nZ4IJDFcv Gn6qQVQPah+MBzkwt4WXy5kDRozCIbg7x+FQBw3KAO23TrLDTFuNsYIWGFcP2CN2 eT8iSP3cWrXNUuEgcPD59aO07rhFooT+QBQFt2ih1dJCV1u/795wb57nxSh1YDcO M2tG+AW2EZky65FXwhLW2rq3LvmTM4kiEz3mA/DrcOAKvvQllK+6FKEhNy0StstP yvvlqoXdgH3sfOnWTAyHr35qA/pMuGEXSryWTJPqpflCvZ3wxNk+IV5nyPAtfaFz CK7U0Ya7NaEp/5ZlpE720apJ4uSqmRrLwk5Y1eKQvT46mGOk3rC9ZPIMXc8mB10/ mJ9mTubi1t4uIPnBl/T1T7f8QhNtr9hOY6wjLf1LoMeJ1XVNBqA+2uydOlBJ1iop RQ7y/Jl1SZ/gBzKCmvjPHT2+0Oui9oXGd9bQi0xQKO5Lus/nAIg= =Wdw1 -----END PGP SIGNATURE----- Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.3 kernel cycle: Core changes: - Device links can optionally be added between a pin control producer and its consumers. This will affect how the system power management is handled: a pin controller will not suspend before all of its consumers have been suspended. This was necessary for the ST Microelectronics STMFX expander and need to be tested on other systems as well: it makes sense to make this default in the long run. Right now it is opt-in per driver. - Drive strength can be specified in microamps. With decreases in silicon technology, milliamps isn't granular enough, let's make it possible to select drive strengths in microamps. Right now the Meson (AMlogic) driver needs this. New drivers: - New subdriver for the Tegra 194 SoC. - New subdriver for the Qualcomm SDM845. - New subdriver for the Qualcomm SM8150. - New subdriver for the Freescale i.MX8MN (Freescale is now a product line of NXP). - New subdriver for Marvell MV98DX1135. Driver improvements: - The Bitmain BM1880 driver now supports pin config in addition to muxing. - The Qualcomm drivers can now reserve some GPIOs as taken aside and not usable for users. This is used in ACPI systems to take out some GPIO lines used by the BIOS so that noone else (neither kernel nor userspace) will play with them by mistake and crash the machine. - A slew of refurbishing around the Aspeed drivers (board management controllers for servers) in preparation for the new Aspeed AST2600 SoC. - A slew of improvements over the SH PFC drivers as usual. - Misc cleanups and fixes" * tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits) pinctrl: aspeed: Strip moved macros and structs from private header pinctrl: aspeed: Fix missed include pinctrl: baytrail: Use GENMASK() consistently pinctrl: baytrail: Re-use data structures from pinctrl-intel.h pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux() pinctrl: qcom: Add SM8150 pinctrl driver dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding dt-bindings: pinctrl: qcom: Document missing gpio nodes pinctrl: aspeed: Add implementation-related documentation pinctrl: aspeed: Split out pinmux from general pinctrl pinctrl: aspeed: Clarify comment about strapping W1C pinctrl: aspeed: Correct comment that is no longer true MAINTAINERS: Add entry for ASPEED pinctrl drivers dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema dt-bindings: pinctrl: aspeed: Split bindings document in two pinctrl: qcom: Add irq_enable callback for msm gpio pinctrl: madera: Fixup SPDX headers pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard pinctrl: tegra: Add bitmask support for parked bits ...
3874 lines
95 KiB
C
3874 lines
95 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Pinctrl driver for Rockchip SoCs
|
|
*
|
|
* Copyright (c) 2013 MundoReader S.L.
|
|
* Author: Heiko Stuebner <heiko@sntech.de>
|
|
*
|
|
* With some ideas taken from pinctrl-samsung:
|
|
* Copyright (c) 2012 Samsung Electronics Co., Ltd.
|
|
* http://www.samsung.com
|
|
* Copyright (c) 2012 Linaro Ltd
|
|
* http://www.linaro.org
|
|
*
|
|
* and pinctrl-at91:
|
|
* Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
*/
|
|
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/io.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/gpio/driver.h>
|
|
#include <linux/of_address.h>
|
|
#include <linux/of_irq.h>
|
|
#include <linux/pinctrl/machine.h>
|
|
#include <linux/pinctrl/pinconf.h>
|
|
#include <linux/pinctrl/pinctrl.h>
|
|
#include <linux/pinctrl/pinmux.h>
|
|
#include <linux/pinctrl/pinconf-generic.h>
|
|
#include <linux/irqchip/chained_irq.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/mfd/syscon.h>
|
|
#include <dt-bindings/pinctrl/rockchip.h>
|
|
|
|
#include "core.h"
|
|
#include "pinconf.h"
|
|
|
|
/* GPIO control registers */
|
|
#define GPIO_SWPORT_DR 0x00
|
|
#define GPIO_SWPORT_DDR 0x04
|
|
#define GPIO_INTEN 0x30
|
|
#define GPIO_INTMASK 0x34
|
|
#define GPIO_INTTYPE_LEVEL 0x38
|
|
#define GPIO_INT_POLARITY 0x3c
|
|
#define GPIO_INT_STATUS 0x40
|
|
#define GPIO_INT_RAWSTATUS 0x44
|
|
#define GPIO_DEBOUNCE 0x48
|
|
#define GPIO_PORTS_EOI 0x4c
|
|
#define GPIO_EXT_PORT 0x50
|
|
#define GPIO_LS_SYNC 0x60
|
|
|
|
enum rockchip_pinctrl_type {
|
|
PX30,
|
|
RV1108,
|
|
RK2928,
|
|
RK3066B,
|
|
RK3128,
|
|
RK3188,
|
|
RK3288,
|
|
RK3368,
|
|
RK3399,
|
|
};
|
|
|
|
/**
|
|
* Encode variants of iomux registers into a type variable
|
|
*/
|
|
#define IOMUX_GPIO_ONLY BIT(0)
|
|
#define IOMUX_WIDTH_4BIT BIT(1)
|
|
#define IOMUX_SOURCE_PMU BIT(2)
|
|
#define IOMUX_UNROUTED BIT(3)
|
|
#define IOMUX_WIDTH_3BIT BIT(4)
|
|
|
|
/**
|
|
* @type: iomux variant using IOMUX_* constants
|
|
* @offset: if initialized to -1 it will be autocalculated, by specifying
|
|
* an initial offset value the relevant source offset can be reset
|
|
* to a new value for autocalculating the following iomux registers.
|
|
*/
|
|
struct rockchip_iomux {
|
|
int type;
|
|
int offset;
|
|
};
|
|
|
|
/**
|
|
* enum type index corresponding to rockchip_perpin_drv_list arrays index.
|
|
*/
|
|
enum rockchip_pin_drv_type {
|
|
DRV_TYPE_IO_DEFAULT = 0,
|
|
DRV_TYPE_IO_1V8_OR_3V0,
|
|
DRV_TYPE_IO_1V8_ONLY,
|
|
DRV_TYPE_IO_1V8_3V0_AUTO,
|
|
DRV_TYPE_IO_3V3_ONLY,
|
|
DRV_TYPE_MAX
|
|
};
|
|
|
|
/**
|
|
* enum type index corresponding to rockchip_pull_list arrays index.
|
|
*/
|
|
enum rockchip_pin_pull_type {
|
|
PULL_TYPE_IO_DEFAULT = 0,
|
|
PULL_TYPE_IO_1V8_ONLY,
|
|
PULL_TYPE_MAX
|
|
};
|
|
|
|
/**
|
|
* @drv_type: drive strength variant using rockchip_perpin_drv_type
|
|
* @offset: if initialized to -1 it will be autocalculated, by specifying
|
|
* an initial offset value the relevant source offset can be reset
|
|
* to a new value for autocalculating the following drive strength
|
|
* registers. if used chips own cal_drv func instead to calculate
|
|
* registers offset, the variant could be ignored.
|
|
*/
|
|
struct rockchip_drv {
|
|
enum rockchip_pin_drv_type drv_type;
|
|
int offset;
|
|
};
|
|
|
|
/**
|
|
* @reg_base: register base of the gpio bank
|
|
* @reg_pull: optional separate register for additional pull settings
|
|
* @clk: clock of the gpio bank
|
|
* @irq: interrupt of the gpio bank
|
|
* @saved_masks: Saved content of GPIO_INTEN at suspend time.
|
|
* @pin_base: first pin number
|
|
* @nr_pins: number of pins in this bank
|
|
* @name: name of the bank
|
|
* @bank_num: number of the bank, to account for holes
|
|
* @iomux: array describing the 4 iomux sources of the bank
|
|
* @drv: array describing the 4 drive strength sources of the bank
|
|
* @pull_type: array describing the 4 pull type sources of the bank
|
|
* @valid: is all necessary information present
|
|
* @of_node: dt node of this bank
|
|
* @drvdata: common pinctrl basedata
|
|
* @domain: irqdomain of the gpio bank
|
|
* @gpio_chip: gpiolib chip
|
|
* @grange: gpio range
|
|
* @slock: spinlock for the gpio bank
|
|
* @route_mask: bits describing the routing pins of per bank
|
|
*/
|
|
struct rockchip_pin_bank {
|
|
void __iomem *reg_base;
|
|
struct regmap *regmap_pull;
|
|
struct clk *clk;
|
|
int irq;
|
|
u32 saved_masks;
|
|
u32 pin_base;
|
|
u8 nr_pins;
|
|
char *name;
|
|
u8 bank_num;
|
|
struct rockchip_iomux iomux[4];
|
|
struct rockchip_drv drv[4];
|
|
enum rockchip_pin_pull_type pull_type[4];
|
|
bool valid;
|
|
struct device_node *of_node;
|
|
struct rockchip_pinctrl *drvdata;
|
|
struct irq_domain *domain;
|
|
struct gpio_chip gpio_chip;
|
|
struct pinctrl_gpio_range grange;
|
|
raw_spinlock_t slock;
|
|
u32 toggle_edge_mode;
|
|
u32 recalced_mask;
|
|
u32 route_mask;
|
|
};
|
|
|
|
#define PIN_BANK(id, pins, label) \
|
|
{ \
|
|
.bank_num = id, \
|
|
.nr_pins = pins, \
|
|
.name = label, \
|
|
.iomux = { \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
}, \
|
|
}
|
|
|
|
#define PIN_BANK_IOMUX_FLAGS(id, pins, label, iom0, iom1, iom2, iom3) \
|
|
{ \
|
|
.bank_num = id, \
|
|
.nr_pins = pins, \
|
|
.name = label, \
|
|
.iomux = { \
|
|
{ .type = iom0, .offset = -1 }, \
|
|
{ .type = iom1, .offset = -1 }, \
|
|
{ .type = iom2, .offset = -1 }, \
|
|
{ .type = iom3, .offset = -1 }, \
|
|
}, \
|
|
}
|
|
|
|
#define PIN_BANK_DRV_FLAGS(id, pins, label, type0, type1, type2, type3) \
|
|
{ \
|
|
.bank_num = id, \
|
|
.nr_pins = pins, \
|
|
.name = label, \
|
|
.iomux = { \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
}, \
|
|
.drv = { \
|
|
{ .drv_type = type0, .offset = -1 }, \
|
|
{ .drv_type = type1, .offset = -1 }, \
|
|
{ .drv_type = type2, .offset = -1 }, \
|
|
{ .drv_type = type3, .offset = -1 }, \
|
|
}, \
|
|
}
|
|
|
|
#define PIN_BANK_DRV_FLAGS_PULL_FLAGS(id, pins, label, drv0, drv1, \
|
|
drv2, drv3, pull0, pull1, \
|
|
pull2, pull3) \
|
|
{ \
|
|
.bank_num = id, \
|
|
.nr_pins = pins, \
|
|
.name = label, \
|
|
.iomux = { \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
{ .offset = -1 }, \
|
|
}, \
|
|
.drv = { \
|
|
{ .drv_type = drv0, .offset = -1 }, \
|
|
{ .drv_type = drv1, .offset = -1 }, \
|
|
{ .drv_type = drv2, .offset = -1 }, \
|
|
{ .drv_type = drv3, .offset = -1 }, \
|
|
}, \
|
|
.pull_type[0] = pull0, \
|
|
.pull_type[1] = pull1, \
|
|
.pull_type[2] = pull2, \
|
|
.pull_type[3] = pull3, \
|
|
}
|
|
|
|
#define PIN_BANK_IOMUX_DRV_FLAGS_OFFSET(id, pins, label, iom0, iom1, \
|
|
iom2, iom3, drv0, drv1, drv2, \
|
|
drv3, offset0, offset1, \
|
|
offset2, offset3) \
|
|
{ \
|
|
.bank_num = id, \
|
|
.nr_pins = pins, \
|
|
.name = label, \
|
|
.iomux = { \
|
|
{ .type = iom0, .offset = -1 }, \
|
|
{ .type = iom1, .offset = -1 }, \
|
|
{ .type = iom2, .offset = -1 }, \
|
|
{ .type = iom3, .offset = -1 }, \
|
|
}, \
|
|
.drv = { \
|
|
{ .drv_type = drv0, .offset = offset0 }, \
|
|
{ .drv_type = drv1, .offset = offset1 }, \
|
|
{ .drv_type = drv2, .offset = offset2 }, \
|
|
{ .drv_type = drv3, .offset = offset3 }, \
|
|
}, \
|
|
}
|
|
|
|
#define PIN_BANK_IOMUX_FLAGS_DRV_FLAGS_OFFSET_PULL_FLAGS(id, pins, \
|
|
label, iom0, iom1, iom2, \
|
|
iom3, drv0, drv1, drv2, \
|
|
drv3, offset0, offset1, \
|
|
offset2, offset3, pull0, \
|
|
pull1, pull2, pull3) \
|
|
{ \
|
|
.bank_num = id, \
|
|
.nr_pins = pins, \
|
|
.name = label, \
|
|
.iomux = { \
|
|
{ .type = iom0, .offset = -1 }, \
|
|
{ .type = iom1, .offset = -1 }, \
|
|
{ .type = iom2, .offset = -1 }, \
|
|
{ .type = iom3, .offset = -1 }, \
|
|
}, \
|
|
.drv = { \
|
|
{ .drv_type = drv0, .offset = offset0 }, \
|
|
{ .drv_type = drv1, .offset = offset1 }, \
|
|
{ .drv_type = drv2, .offset = offset2 }, \
|
|
{ .drv_type = drv3, .offset = offset3 }, \
|
|
}, \
|
|
.pull_type[0] = pull0, \
|
|
.pull_type[1] = pull1, \
|
|
.pull_type[2] = pull2, \
|
|
.pull_type[3] = pull3, \
|
|
}
|
|
|
|
/**
|
|
* struct rockchip_mux_recalced_data: represent a pin iomux data.
|
|
* @num: bank number.
|
|
* @pin: pin number.
|
|
* @bit: index at register.
|
|
* @reg: register offset.
|
|
* @mask: mask bit
|
|
*/
|
|
struct rockchip_mux_recalced_data {
|
|
u8 num;
|
|
u8 pin;
|
|
u32 reg;
|
|
u8 bit;
|
|
u8 mask;
|
|
};
|
|
|
|
enum rockchip_mux_route_location {
|
|
ROCKCHIP_ROUTE_SAME = 0,
|
|
ROCKCHIP_ROUTE_PMU,
|
|
ROCKCHIP_ROUTE_GRF,
|
|
};
|
|
|
|
/**
|
|
* struct rockchip_mux_recalced_data: represent a pin iomux data.
|
|
* @bank_num: bank number.
|
|
* @pin: index at register or used to calc index.
|
|
* @func: the min pin.
|
|
* @route_offset: the max pin.
|
|
* @route_val: the register offset.
|
|
*/
|
|
struct rockchip_mux_route_data {
|
|
u8 bank_num;
|
|
u8 pin;
|
|
u8 func;
|
|
enum rockchip_mux_route_location route_location;
|
|
u32 route_offset;
|
|
u32 route_val;
|
|
};
|
|
|
|
/**
|
|
*/
|
|
struct rockchip_pin_ctrl {
|
|
struct rockchip_pin_bank *pin_banks;
|
|
u32 nr_banks;
|
|
u32 nr_pins;
|
|
char *label;
|
|
enum rockchip_pinctrl_type type;
|
|
int grf_mux_offset;
|
|
int pmu_mux_offset;
|
|
int grf_drv_offset;
|
|
int pmu_drv_offset;
|
|
struct rockchip_mux_recalced_data *iomux_recalced;
|
|
u32 niomux_recalced;
|
|
struct rockchip_mux_route_data *iomux_routes;
|
|
u32 niomux_routes;
|
|
|
|
void (*pull_calc_reg)(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit);
|
|
void (*drv_calc_reg)(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit);
|
|
int (*schmitt_calc_reg)(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit);
|
|
};
|
|
|
|
struct rockchip_pin_config {
|
|
unsigned int func;
|
|
unsigned long *configs;
|
|
unsigned int nconfigs;
|
|
};
|
|
|
|
/**
|
|
* struct rockchip_pin_group: represent group of pins of a pinmux function.
|
|
* @name: name of the pin group, used to lookup the group.
|
|
* @pins: the pins included in this group.
|
|
* @npins: number of pins included in this group.
|
|
* @func: the mux function number to be programmed when selected.
|
|
* @configs: the config values to be set for each pin
|
|
* @nconfigs: number of configs for each pin
|
|
*/
|
|
struct rockchip_pin_group {
|
|
const char *name;
|
|
unsigned int npins;
|
|
unsigned int *pins;
|
|
struct rockchip_pin_config *data;
|
|
};
|
|
|
|
/**
|
|
* struct rockchip_pmx_func: represent a pin function.
|
|
* @name: name of the pin function, used to lookup the function.
|
|
* @groups: one or more names of pin groups that provide this function.
|
|
* @num_groups: number of groups included in @groups.
|
|
*/
|
|
struct rockchip_pmx_func {
|
|
const char *name;
|
|
const char **groups;
|
|
u8 ngroups;
|
|
};
|
|
|
|
struct rockchip_pinctrl {
|
|
struct regmap *regmap_base;
|
|
int reg_size;
|
|
struct regmap *regmap_pull;
|
|
struct regmap *regmap_pmu;
|
|
struct device *dev;
|
|
struct rockchip_pin_ctrl *ctrl;
|
|
struct pinctrl_desc pctl;
|
|
struct pinctrl_dev *pctl_dev;
|
|
struct rockchip_pin_group *groups;
|
|
unsigned int ngroups;
|
|
struct rockchip_pmx_func *functions;
|
|
unsigned int nfunctions;
|
|
};
|
|
|
|
static struct regmap_config rockchip_regmap_config = {
|
|
.reg_bits = 32,
|
|
.val_bits = 32,
|
|
.reg_stride = 4,
|
|
};
|
|
|
|
static inline const struct rockchip_pin_group *pinctrl_name_to_group(
|
|
const struct rockchip_pinctrl *info,
|
|
const char *name)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < info->ngroups; i++) {
|
|
if (!strcmp(info->groups[i].name, name))
|
|
return &info->groups[i];
|
|
}
|
|
|
|
return NULL;
|
|
}
|
|
|
|
/*
|
|
* given a pin number that is local to a pin controller, find out the pin bank
|
|
* and the register base of the pin bank.
|
|
*/
|
|
static struct rockchip_pin_bank *pin_to_bank(struct rockchip_pinctrl *info,
|
|
unsigned pin)
|
|
{
|
|
struct rockchip_pin_bank *b = info->ctrl->pin_banks;
|
|
|
|
while (pin >= (b->pin_base + b->nr_pins))
|
|
b++;
|
|
|
|
return b;
|
|
}
|
|
|
|
static struct rockchip_pin_bank *bank_num_to_bank(
|
|
struct rockchip_pinctrl *info,
|
|
unsigned num)
|
|
{
|
|
struct rockchip_pin_bank *b = info->ctrl->pin_banks;
|
|
int i;
|
|
|
|
for (i = 0; i < info->ctrl->nr_banks; i++, b++) {
|
|
if (b->bank_num == num)
|
|
return b;
|
|
}
|
|
|
|
return ERR_PTR(-EINVAL);
|
|
}
|
|
|
|
/*
|
|
* Pinctrl_ops handling
|
|
*/
|
|
|
|
static int rockchip_get_groups_count(struct pinctrl_dev *pctldev)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
return info->ngroups;
|
|
}
|
|
|
|
static const char *rockchip_get_group_name(struct pinctrl_dev *pctldev,
|
|
unsigned selector)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
return info->groups[selector].name;
|
|
}
|
|
|
|
static int rockchip_get_group_pins(struct pinctrl_dev *pctldev,
|
|
unsigned selector, const unsigned **pins,
|
|
unsigned *npins)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
if (selector >= info->ngroups)
|
|
return -EINVAL;
|
|
|
|
*pins = info->groups[selector].pins;
|
|
*npins = info->groups[selector].npins;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_dt_node_to_map(struct pinctrl_dev *pctldev,
|
|
struct device_node *np,
|
|
struct pinctrl_map **map, unsigned *num_maps)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
const struct rockchip_pin_group *grp;
|
|
struct pinctrl_map *new_map;
|
|
struct device_node *parent;
|
|
int map_num = 1;
|
|
int i;
|
|
|
|
/*
|
|
* first find the group of this node and check if we need to create
|
|
* config maps for pins
|
|
*/
|
|
grp = pinctrl_name_to_group(info, np->name);
|
|
if (!grp) {
|
|
dev_err(info->dev, "unable to find group for node %pOFn\n",
|
|
np);
|
|
return -EINVAL;
|
|
}
|
|
|
|
map_num += grp->npins;
|
|
new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map),
|
|
GFP_KERNEL);
|
|
if (!new_map)
|
|
return -ENOMEM;
|
|
|
|
*map = new_map;
|
|
*num_maps = map_num;
|
|
|
|
/* create mux map */
|
|
parent = of_get_parent(np);
|
|
if (!parent) {
|
|
devm_kfree(pctldev->dev, new_map);
|
|
return -EINVAL;
|
|
}
|
|
new_map[0].type = PIN_MAP_TYPE_MUX_GROUP;
|
|
new_map[0].data.mux.function = parent->name;
|
|
new_map[0].data.mux.group = np->name;
|
|
of_node_put(parent);
|
|
|
|
/* create config map */
|
|
new_map++;
|
|
for (i = 0; i < grp->npins; i++) {
|
|
new_map[i].type = PIN_MAP_TYPE_CONFIGS_PIN;
|
|
new_map[i].data.configs.group_or_pin =
|
|
pin_get_name(pctldev, grp->pins[i]);
|
|
new_map[i].data.configs.configs = grp->data[i].configs;
|
|
new_map[i].data.configs.num_configs = grp->data[i].nconfigs;
|
|
}
|
|
|
|
dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n",
|
|
(*map)->data.mux.function, (*map)->data.mux.group, map_num);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void rockchip_dt_free_map(struct pinctrl_dev *pctldev,
|
|
struct pinctrl_map *map, unsigned num_maps)
|
|
{
|
|
}
|
|
|
|
static const struct pinctrl_ops rockchip_pctrl_ops = {
|
|
.get_groups_count = rockchip_get_groups_count,
|
|
.get_group_name = rockchip_get_group_name,
|
|
.get_group_pins = rockchip_get_group_pins,
|
|
.dt_node_to_map = rockchip_dt_node_to_map,
|
|
.dt_free_map = rockchip_dt_free_map,
|
|
};
|
|
|
|
/*
|
|
* Hardware access
|
|
*/
|
|
|
|
static struct rockchip_mux_recalced_data rv1108_mux_recalced_data[] = {
|
|
{
|
|
.num = 1,
|
|
.pin = 0,
|
|
.reg = 0x418,
|
|
.bit = 0,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 1,
|
|
.reg = 0x418,
|
|
.bit = 2,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 2,
|
|
.reg = 0x418,
|
|
.bit = 4,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 3,
|
|
.reg = 0x418,
|
|
.bit = 6,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 4,
|
|
.reg = 0x418,
|
|
.bit = 8,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 5,
|
|
.reg = 0x418,
|
|
.bit = 10,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 6,
|
|
.reg = 0x418,
|
|
.bit = 12,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 7,
|
|
.reg = 0x418,
|
|
.bit = 14,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 8,
|
|
.reg = 0x41c,
|
|
.bit = 0,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 1,
|
|
.pin = 9,
|
|
.reg = 0x41c,
|
|
.bit = 2,
|
|
.mask = 0x3
|
|
},
|
|
};
|
|
|
|
static struct rockchip_mux_recalced_data rk3128_mux_recalced_data[] = {
|
|
{
|
|
.num = 2,
|
|
.pin = 20,
|
|
.reg = 0xe8,
|
|
.bit = 0,
|
|
.mask = 0x7
|
|
}, {
|
|
.num = 2,
|
|
.pin = 21,
|
|
.reg = 0xe8,
|
|
.bit = 4,
|
|
.mask = 0x7
|
|
}, {
|
|
.num = 2,
|
|
.pin = 22,
|
|
.reg = 0xe8,
|
|
.bit = 8,
|
|
.mask = 0x7
|
|
}, {
|
|
.num = 2,
|
|
.pin = 23,
|
|
.reg = 0xe8,
|
|
.bit = 12,
|
|
.mask = 0x7
|
|
}, {
|
|
.num = 2,
|
|
.pin = 24,
|
|
.reg = 0xd4,
|
|
.bit = 12,
|
|
.mask = 0x7
|
|
},
|
|
};
|
|
|
|
static struct rockchip_mux_recalced_data rk3328_mux_recalced_data[] = {
|
|
{
|
|
.num = 2,
|
|
.pin = 12,
|
|
.reg = 0x24,
|
|
.bit = 8,
|
|
.mask = 0x3
|
|
}, {
|
|
.num = 2,
|
|
.pin = 15,
|
|
.reg = 0x28,
|
|
.bit = 0,
|
|
.mask = 0x7
|
|
}, {
|
|
.num = 2,
|
|
.pin = 23,
|
|
.reg = 0x30,
|
|
.bit = 14,
|
|
.mask = 0x3
|
|
},
|
|
};
|
|
|
|
static void rockchip_get_recalced_mux(struct rockchip_pin_bank *bank, int pin,
|
|
int *reg, u8 *bit, int *mask)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct rockchip_mux_recalced_data *data;
|
|
int i;
|
|
|
|
for (i = 0; i < ctrl->niomux_recalced; i++) {
|
|
data = &ctrl->iomux_recalced[i];
|
|
if (data->num == bank->bank_num &&
|
|
data->pin == pin)
|
|
break;
|
|
}
|
|
|
|
if (i >= ctrl->niomux_recalced)
|
|
return;
|
|
|
|
*reg = data->reg;
|
|
*mask = data->mask;
|
|
*bit = data->bit;
|
|
}
|
|
|
|
static struct rockchip_mux_route_data px30_mux_route_data[] = {
|
|
{
|
|
/* cif-d2m0 */
|
|
.bank_num = 2,
|
|
.pin = 0,
|
|
.func = 1,
|
|
.route_offset = 0x184,
|
|
.route_val = BIT(16 + 7),
|
|
}, {
|
|
/* cif-d2m1 */
|
|
.bank_num = 3,
|
|
.pin = 3,
|
|
.func = 3,
|
|
.route_offset = 0x184,
|
|
.route_val = BIT(16 + 7) | BIT(7),
|
|
}, {
|
|
/* pdm-m0 */
|
|
.bank_num = 3,
|
|
.pin = 22,
|
|
.func = 2,
|
|
.route_offset = 0x184,
|
|
.route_val = BIT(16 + 8),
|
|
}, {
|
|
/* pdm-m1 */
|
|
.bank_num = 2,
|
|
.pin = 22,
|
|
.func = 1,
|
|
.route_offset = 0x184,
|
|
.route_val = BIT(16 + 8) | BIT(8),
|
|
}, {
|
|
/* uart2-rxm0 */
|
|
.bank_num = 1,
|
|
.pin = 27,
|
|
.func = 2,
|
|
.route_offset = 0x184,
|
|
.route_val = BIT(16 + 10),
|
|
}, {
|
|
/* uart2-rxm1 */
|
|
.bank_num = 2,
|
|
.pin = 14,
|
|
.func = 2,
|
|
.route_offset = 0x184,
|
|
.route_val = BIT(16 + 10) | BIT(10),
|
|
}, {
|
|
/* uart3-rxm0 */
|
|
.bank_num = 0,
|
|
.pin = 17,
|
|
.func = 2,
|
|
.route_offset = 0x184,
|
|
.route_val = BIT(16 + 9),
|
|
}, {
|
|
/* uart3-rxm1 */
|
|
.bank_num = 1,
|
|
.pin = 15,
|
|
.func = 2,
|
|
.route_offset = 0x184,
|
|
.route_val = BIT(16 + 9) | BIT(9),
|
|
},
|
|
};
|
|
|
|
static struct rockchip_mux_route_data rk3128_mux_route_data[] = {
|
|
{
|
|
/* spi-0 */
|
|
.bank_num = 1,
|
|
.pin = 10,
|
|
.func = 1,
|
|
.route_offset = 0x144,
|
|
.route_val = BIT(16 + 3) | BIT(16 + 4),
|
|
}, {
|
|
/* spi-1 */
|
|
.bank_num = 1,
|
|
.pin = 27,
|
|
.func = 3,
|
|
.route_offset = 0x144,
|
|
.route_val = BIT(16 + 3) | BIT(16 + 4) | BIT(3),
|
|
}, {
|
|
/* spi-2 */
|
|
.bank_num = 0,
|
|
.pin = 13,
|
|
.func = 2,
|
|
.route_offset = 0x144,
|
|
.route_val = BIT(16 + 3) | BIT(16 + 4) | BIT(4),
|
|
}, {
|
|
/* i2s-0 */
|
|
.bank_num = 1,
|
|
.pin = 5,
|
|
.func = 1,
|
|
.route_offset = 0x144,
|
|
.route_val = BIT(16 + 5),
|
|
}, {
|
|
/* i2s-1 */
|
|
.bank_num = 0,
|
|
.pin = 14,
|
|
.func = 1,
|
|
.route_offset = 0x144,
|
|
.route_val = BIT(16 + 5) | BIT(5),
|
|
}, {
|
|
/* emmc-0 */
|
|
.bank_num = 1,
|
|
.pin = 22,
|
|
.func = 2,
|
|
.route_offset = 0x144,
|
|
.route_val = BIT(16 + 6),
|
|
}, {
|
|
/* emmc-1 */
|
|
.bank_num = 2,
|
|
.pin = 4,
|
|
.func = 2,
|
|
.route_offset = 0x144,
|
|
.route_val = BIT(16 + 6) | BIT(6),
|
|
},
|
|
};
|
|
|
|
static struct rockchip_mux_route_data rk3188_mux_route_data[] = {
|
|
{
|
|
/* non-iomuxed emmc/flash pins on flash-dqs */
|
|
.bank_num = 0,
|
|
.pin = 24,
|
|
.func = 1,
|
|
.route_location = ROCKCHIP_ROUTE_GRF,
|
|
.route_offset = 0xa0,
|
|
.route_val = BIT(16 + 11),
|
|
}, {
|
|
/* non-iomuxed emmc/flash pins on emmc-clk */
|
|
.bank_num = 0,
|
|
.pin = 24,
|
|
.func = 2,
|
|
.route_location = ROCKCHIP_ROUTE_GRF,
|
|
.route_offset = 0xa0,
|
|
.route_val = BIT(16 + 11) | BIT(11),
|
|
},
|
|
};
|
|
|
|
static struct rockchip_mux_route_data rk3228_mux_route_data[] = {
|
|
{
|
|
/* pwm0-0 */
|
|
.bank_num = 0,
|
|
.pin = 26,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16),
|
|
}, {
|
|
/* pwm0-1 */
|
|
.bank_num = 3,
|
|
.pin = 21,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16) | BIT(0),
|
|
}, {
|
|
/* pwm1-0 */
|
|
.bank_num = 0,
|
|
.pin = 27,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 1),
|
|
}, {
|
|
/* pwm1-1 */
|
|
.bank_num = 0,
|
|
.pin = 30,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 1) | BIT(1),
|
|
}, {
|
|
/* pwm2-0 */
|
|
.bank_num = 0,
|
|
.pin = 28,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 2),
|
|
}, {
|
|
/* pwm2-1 */
|
|
.bank_num = 1,
|
|
.pin = 12,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 2) | BIT(2),
|
|
}, {
|
|
/* pwm3-0 */
|
|
.bank_num = 3,
|
|
.pin = 26,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 3),
|
|
}, {
|
|
/* pwm3-1 */
|
|
.bank_num = 1,
|
|
.pin = 11,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 3) | BIT(3),
|
|
}, {
|
|
/* sdio-0_d0 */
|
|
.bank_num = 1,
|
|
.pin = 1,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 4),
|
|
}, {
|
|
/* sdio-1_d0 */
|
|
.bank_num = 3,
|
|
.pin = 2,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 4) | BIT(4),
|
|
}, {
|
|
/* spi-0_rx */
|
|
.bank_num = 0,
|
|
.pin = 13,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 5),
|
|
}, {
|
|
/* spi-1_rx */
|
|
.bank_num = 2,
|
|
.pin = 0,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 5) | BIT(5),
|
|
}, {
|
|
/* emmc-0_cmd */
|
|
.bank_num = 1,
|
|
.pin = 22,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 7),
|
|
}, {
|
|
/* emmc-1_cmd */
|
|
.bank_num = 2,
|
|
.pin = 4,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 7) | BIT(7),
|
|
}, {
|
|
/* uart2-0_rx */
|
|
.bank_num = 1,
|
|
.pin = 19,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 8),
|
|
}, {
|
|
/* uart2-1_rx */
|
|
.bank_num = 1,
|
|
.pin = 10,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 8) | BIT(8),
|
|
}, {
|
|
/* uart1-0_rx */
|
|
.bank_num = 1,
|
|
.pin = 10,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 11),
|
|
}, {
|
|
/* uart1-1_rx */
|
|
.bank_num = 3,
|
|
.pin = 13,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 11) | BIT(11),
|
|
},
|
|
};
|
|
|
|
static struct rockchip_mux_route_data rk3288_mux_route_data[] = {
|
|
{
|
|
/* edphdmi_cecinoutt1 */
|
|
.bank_num = 7,
|
|
.pin = 16,
|
|
.func = 2,
|
|
.route_offset = 0x264,
|
|
.route_val = BIT(16 + 12) | BIT(12),
|
|
}, {
|
|
/* edphdmi_cecinout */
|
|
.bank_num = 7,
|
|
.pin = 23,
|
|
.func = 4,
|
|
.route_offset = 0x264,
|
|
.route_val = BIT(16 + 12),
|
|
},
|
|
};
|
|
|
|
static struct rockchip_mux_route_data rk3328_mux_route_data[] = {
|
|
{
|
|
/* uart2dbg_rxm0 */
|
|
.bank_num = 1,
|
|
.pin = 1,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16) | BIT(16 + 1),
|
|
}, {
|
|
/* uart2dbg_rxm1 */
|
|
.bank_num = 2,
|
|
.pin = 1,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16) | BIT(16 + 1) | BIT(0),
|
|
}, {
|
|
/* gmac-m1_rxd0 */
|
|
.bank_num = 1,
|
|
.pin = 11,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 2) | BIT(2),
|
|
}, {
|
|
/* gmac-m1-optimized_rxd3 */
|
|
.bank_num = 1,
|
|
.pin = 14,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 10) | BIT(10),
|
|
}, {
|
|
/* pdm_sdi0m0 */
|
|
.bank_num = 2,
|
|
.pin = 19,
|
|
.func = 2,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 3),
|
|
}, {
|
|
/* pdm_sdi0m1 */
|
|
.bank_num = 1,
|
|
.pin = 23,
|
|
.func = 3,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 3) | BIT(3),
|
|
}, {
|
|
/* spi_rxdm2 */
|
|
.bank_num = 3,
|
|
.pin = 2,
|
|
.func = 4,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 4) | BIT(16 + 5) | BIT(5),
|
|
}, {
|
|
/* i2s2_sdim0 */
|
|
.bank_num = 1,
|
|
.pin = 24,
|
|
.func = 1,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 6),
|
|
}, {
|
|
/* i2s2_sdim1 */
|
|
.bank_num = 3,
|
|
.pin = 2,
|
|
.func = 6,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 6) | BIT(6),
|
|
}, {
|
|
/* card_iom1 */
|
|
.bank_num = 2,
|
|
.pin = 22,
|
|
.func = 3,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 7) | BIT(7),
|
|
}, {
|
|
/* tsp_d5m1 */
|
|
.bank_num = 2,
|
|
.pin = 16,
|
|
.func = 3,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 8) | BIT(8),
|
|
}, {
|
|
/* cif_data5m1 */
|
|
.bank_num = 2,
|
|
.pin = 16,
|
|
.func = 4,
|
|
.route_offset = 0x50,
|
|
.route_val = BIT(16 + 9) | BIT(9),
|
|
},
|
|
};
|
|
|
|
static struct rockchip_mux_route_data rk3399_mux_route_data[] = {
|
|
{
|
|
/* uart2dbga_rx */
|
|
.bank_num = 4,
|
|
.pin = 8,
|
|
.func = 2,
|
|
.route_offset = 0xe21c,
|
|
.route_val = BIT(16 + 10) | BIT(16 + 11),
|
|
}, {
|
|
/* uart2dbgb_rx */
|
|
.bank_num = 4,
|
|
.pin = 16,
|
|
.func = 2,
|
|
.route_offset = 0xe21c,
|
|
.route_val = BIT(16 + 10) | BIT(16 + 11) | BIT(10),
|
|
}, {
|
|
/* uart2dbgc_rx */
|
|
.bank_num = 4,
|
|
.pin = 19,
|
|
.func = 1,
|
|
.route_offset = 0xe21c,
|
|
.route_val = BIT(16 + 10) | BIT(16 + 11) | BIT(11),
|
|
}, {
|
|
/* pcie_clkreqn */
|
|
.bank_num = 2,
|
|
.pin = 26,
|
|
.func = 2,
|
|
.route_offset = 0xe21c,
|
|
.route_val = BIT(16 + 14),
|
|
}, {
|
|
/* pcie_clkreqnb */
|
|
.bank_num = 4,
|
|
.pin = 24,
|
|
.func = 1,
|
|
.route_offset = 0xe21c,
|
|
.route_val = BIT(16 + 14) | BIT(14),
|
|
},
|
|
};
|
|
|
|
static bool rockchip_get_mux_route(struct rockchip_pin_bank *bank, int pin,
|
|
int mux, u32 *loc, u32 *reg, u32 *value)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct rockchip_mux_route_data *data;
|
|
int i;
|
|
|
|
for (i = 0; i < ctrl->niomux_routes; i++) {
|
|
data = &ctrl->iomux_routes[i];
|
|
if ((data->bank_num == bank->bank_num) &&
|
|
(data->pin == pin) && (data->func == mux))
|
|
break;
|
|
}
|
|
|
|
if (i >= ctrl->niomux_routes)
|
|
return false;
|
|
|
|
*loc = data->route_location;
|
|
*reg = data->route_offset;
|
|
*value = data->route_val;
|
|
|
|
return true;
|
|
}
|
|
|
|
static int rockchip_get_mux(struct rockchip_pin_bank *bank, int pin)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
int iomux_num = (pin / 8);
|
|
struct regmap *regmap;
|
|
unsigned int val;
|
|
int reg, ret, mask, mux_type;
|
|
u8 bit;
|
|
|
|
if (iomux_num > 3)
|
|
return -EINVAL;
|
|
|
|
if (bank->iomux[iomux_num].type & IOMUX_UNROUTED) {
|
|
dev_err(info->dev, "pin %d is unrouted\n", pin);
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY)
|
|
return RK_FUNC_GPIO;
|
|
|
|
regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
|
|
? info->regmap_pmu : info->regmap_base;
|
|
|
|
/* get basic quadrupel of mux registers and the correct reg inside */
|
|
mux_type = bank->iomux[iomux_num].type;
|
|
reg = bank->iomux[iomux_num].offset;
|
|
if (mux_type & IOMUX_WIDTH_4BIT) {
|
|
if ((pin % 8) >= 4)
|
|
reg += 0x4;
|
|
bit = (pin % 4) * 4;
|
|
mask = 0xf;
|
|
} else if (mux_type & IOMUX_WIDTH_3BIT) {
|
|
if ((pin % 8) >= 5)
|
|
reg += 0x4;
|
|
bit = (pin % 8 % 5) * 3;
|
|
mask = 0x7;
|
|
} else {
|
|
bit = (pin % 8) * 2;
|
|
mask = 0x3;
|
|
}
|
|
|
|
if (bank->recalced_mask & BIT(pin))
|
|
rockchip_get_recalced_mux(bank, pin, ®, &bit, &mask);
|
|
|
|
ret = regmap_read(regmap, reg, &val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return ((val >> bit) & mask);
|
|
}
|
|
|
|
static int rockchip_verify_mux(struct rockchip_pin_bank *bank,
|
|
int pin, int mux)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
int iomux_num = (pin / 8);
|
|
|
|
if (iomux_num > 3)
|
|
return -EINVAL;
|
|
|
|
if (bank->iomux[iomux_num].type & IOMUX_UNROUTED) {
|
|
dev_err(info->dev, "pin %d is unrouted\n", pin);
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY) {
|
|
if (mux != RK_FUNC_GPIO) {
|
|
dev_err(info->dev,
|
|
"pin %d only supports a gpio mux\n", pin);
|
|
return -ENOTSUPP;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Set a new mux function for a pin.
|
|
*
|
|
* The register is divided into the upper and lower 16 bit. When changing
|
|
* a value, the previous register value is not read and changed. Instead
|
|
* it seems the changed bits are marked in the upper 16 bit, while the
|
|
* changed value gets set in the same offset in the lower 16 bit.
|
|
* All pin settings seem to be 2 bit wide in both the upper and lower
|
|
* parts.
|
|
* @bank: pin bank to change
|
|
* @pin: pin to change
|
|
* @mux: new mux function to set
|
|
*/
|
|
static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
int iomux_num = (pin / 8);
|
|
struct regmap *regmap;
|
|
int reg, ret, mask, mux_type;
|
|
u8 bit;
|
|
u32 data, rmask, route_location, route_reg, route_val;
|
|
|
|
ret = rockchip_verify_mux(bank, pin, mux);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY)
|
|
return 0;
|
|
|
|
dev_dbg(info->dev, "setting mux of GPIO%d-%d to %d\n",
|
|
bank->bank_num, pin, mux);
|
|
|
|
regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
|
|
? info->regmap_pmu : info->regmap_base;
|
|
|
|
/* get basic quadrupel of mux registers and the correct reg inside */
|
|
mux_type = bank->iomux[iomux_num].type;
|
|
reg = bank->iomux[iomux_num].offset;
|
|
if (mux_type & IOMUX_WIDTH_4BIT) {
|
|
if ((pin % 8) >= 4)
|
|
reg += 0x4;
|
|
bit = (pin % 4) * 4;
|
|
mask = 0xf;
|
|
} else if (mux_type & IOMUX_WIDTH_3BIT) {
|
|
if ((pin % 8) >= 5)
|
|
reg += 0x4;
|
|
bit = (pin % 8 % 5) * 3;
|
|
mask = 0x7;
|
|
} else {
|
|
bit = (pin % 8) * 2;
|
|
mask = 0x3;
|
|
}
|
|
|
|
if (bank->recalced_mask & BIT(pin))
|
|
rockchip_get_recalced_mux(bank, pin, ®, &bit, &mask);
|
|
|
|
if (bank->route_mask & BIT(pin)) {
|
|
if (rockchip_get_mux_route(bank, pin, mux, &route_location,
|
|
&route_reg, &route_val)) {
|
|
struct regmap *route_regmap = regmap;
|
|
|
|
/* handle special locations */
|
|
switch (route_location) {
|
|
case ROCKCHIP_ROUTE_PMU:
|
|
route_regmap = info->regmap_pmu;
|
|
break;
|
|
case ROCKCHIP_ROUTE_GRF:
|
|
route_regmap = info->regmap_base;
|
|
break;
|
|
}
|
|
|
|
ret = regmap_write(route_regmap, route_reg, route_val);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
data = (mask << (bit + 16));
|
|
rmask = data | (data >> 16);
|
|
data |= (mux & mask) << bit;
|
|
ret = regmap_update_bits(regmap, reg, rmask, data);
|
|
|
|
return ret;
|
|
}
|
|
|
|
#define PX30_PULL_PMU_OFFSET 0x10
|
|
#define PX30_PULL_GRF_OFFSET 0x60
|
|
#define PX30_PULL_BITS_PER_PIN 2
|
|
#define PX30_PULL_PINS_PER_REG 8
|
|
#define PX30_PULL_BANK_STRIDE 16
|
|
|
|
static void px30_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 32 pins of the first bank are located in PMU */
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = PX30_PULL_PMU_OFFSET;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = PX30_PULL_GRF_OFFSET;
|
|
|
|
/* correct the offset, as we're starting with the 2nd bank */
|
|
*reg -= 0x10;
|
|
*reg += bank->bank_num * PX30_PULL_BANK_STRIDE;
|
|
}
|
|
|
|
*reg += ((pin_num / PX30_PULL_PINS_PER_REG) * 4);
|
|
*bit = (pin_num % PX30_PULL_PINS_PER_REG);
|
|
*bit *= PX30_PULL_BITS_PER_PIN;
|
|
}
|
|
|
|
#define PX30_DRV_PMU_OFFSET 0x20
|
|
#define PX30_DRV_GRF_OFFSET 0xf0
|
|
#define PX30_DRV_BITS_PER_PIN 2
|
|
#define PX30_DRV_PINS_PER_REG 8
|
|
#define PX30_DRV_BANK_STRIDE 16
|
|
|
|
static void px30_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 32 pins of the first bank are located in PMU */
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = PX30_DRV_PMU_OFFSET;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = PX30_DRV_GRF_OFFSET;
|
|
|
|
/* correct the offset, as we're starting with the 2nd bank */
|
|
*reg -= 0x10;
|
|
*reg += bank->bank_num * PX30_DRV_BANK_STRIDE;
|
|
}
|
|
|
|
*reg += ((pin_num / PX30_DRV_PINS_PER_REG) * 4);
|
|
*bit = (pin_num % PX30_DRV_PINS_PER_REG);
|
|
*bit *= PX30_DRV_BITS_PER_PIN;
|
|
}
|
|
|
|
#define PX30_SCHMITT_PMU_OFFSET 0x38
|
|
#define PX30_SCHMITT_GRF_OFFSET 0xc0
|
|
#define PX30_SCHMITT_PINS_PER_PMU_REG 16
|
|
#define PX30_SCHMITT_BANK_STRIDE 16
|
|
#define PX30_SCHMITT_PINS_PER_GRF_REG 8
|
|
|
|
static int px30_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num,
|
|
struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
int pins_per_reg;
|
|
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = PX30_SCHMITT_PMU_OFFSET;
|
|
pins_per_reg = PX30_SCHMITT_PINS_PER_PMU_REG;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = PX30_SCHMITT_GRF_OFFSET;
|
|
pins_per_reg = PX30_SCHMITT_PINS_PER_GRF_REG;
|
|
*reg += (bank->bank_num - 1) * PX30_SCHMITT_BANK_STRIDE;
|
|
}
|
|
|
|
*reg += ((pin_num / pins_per_reg) * 4);
|
|
*bit = pin_num % pins_per_reg;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define RV1108_PULL_PMU_OFFSET 0x10
|
|
#define RV1108_PULL_OFFSET 0x110
|
|
#define RV1108_PULL_PINS_PER_REG 8
|
|
#define RV1108_PULL_BITS_PER_PIN 2
|
|
#define RV1108_PULL_BANK_STRIDE 16
|
|
|
|
static void rv1108_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 24 pins of the first bank are located in PMU */
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = RV1108_PULL_PMU_OFFSET;
|
|
} else {
|
|
*reg = RV1108_PULL_OFFSET;
|
|
*regmap = info->regmap_base;
|
|
/* correct the offset, as we're starting with the 2nd bank */
|
|
*reg -= 0x10;
|
|
*reg += bank->bank_num * RV1108_PULL_BANK_STRIDE;
|
|
}
|
|
|
|
*reg += ((pin_num / RV1108_PULL_PINS_PER_REG) * 4);
|
|
*bit = (pin_num % RV1108_PULL_PINS_PER_REG);
|
|
*bit *= RV1108_PULL_BITS_PER_PIN;
|
|
}
|
|
|
|
#define RV1108_DRV_PMU_OFFSET 0x20
|
|
#define RV1108_DRV_GRF_OFFSET 0x210
|
|
#define RV1108_DRV_BITS_PER_PIN 2
|
|
#define RV1108_DRV_PINS_PER_REG 8
|
|
#define RV1108_DRV_BANK_STRIDE 16
|
|
|
|
static void rv1108_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 24 pins of the first bank are located in PMU */
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = RV1108_DRV_PMU_OFFSET;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = RV1108_DRV_GRF_OFFSET;
|
|
|
|
/* correct the offset, as we're starting with the 2nd bank */
|
|
*reg -= 0x10;
|
|
*reg += bank->bank_num * RV1108_DRV_BANK_STRIDE;
|
|
}
|
|
|
|
*reg += ((pin_num / RV1108_DRV_PINS_PER_REG) * 4);
|
|
*bit = pin_num % RV1108_DRV_PINS_PER_REG;
|
|
*bit *= RV1108_DRV_BITS_PER_PIN;
|
|
}
|
|
|
|
#define RV1108_SCHMITT_PMU_OFFSET 0x30
|
|
#define RV1108_SCHMITT_GRF_OFFSET 0x388
|
|
#define RV1108_SCHMITT_BANK_STRIDE 8
|
|
#define RV1108_SCHMITT_PINS_PER_GRF_REG 16
|
|
#define RV1108_SCHMITT_PINS_PER_PMU_REG 8
|
|
|
|
static int rv1108_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num,
|
|
struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
int pins_per_reg;
|
|
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = RV1108_SCHMITT_PMU_OFFSET;
|
|
pins_per_reg = RV1108_SCHMITT_PINS_PER_PMU_REG;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = RV1108_SCHMITT_GRF_OFFSET;
|
|
pins_per_reg = RV1108_SCHMITT_PINS_PER_GRF_REG;
|
|
*reg += (bank->bank_num - 1) * RV1108_SCHMITT_BANK_STRIDE;
|
|
}
|
|
*reg += ((pin_num / pins_per_reg) * 4);
|
|
*bit = pin_num % pins_per_reg;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define RK2928_PULL_OFFSET 0x118
|
|
#define RK2928_PULL_PINS_PER_REG 16
|
|
#define RK2928_PULL_BANK_STRIDE 8
|
|
|
|
static void rk2928_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
*regmap = info->regmap_base;
|
|
*reg = RK2928_PULL_OFFSET;
|
|
*reg += bank->bank_num * RK2928_PULL_BANK_STRIDE;
|
|
*reg += (pin_num / RK2928_PULL_PINS_PER_REG) * 4;
|
|
|
|
*bit = pin_num % RK2928_PULL_PINS_PER_REG;
|
|
};
|
|
|
|
#define RK3128_PULL_OFFSET 0x118
|
|
|
|
static void rk3128_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3128_PULL_OFFSET;
|
|
*reg += bank->bank_num * RK2928_PULL_BANK_STRIDE;
|
|
*reg += ((pin_num / RK2928_PULL_PINS_PER_REG) * 4);
|
|
|
|
*bit = pin_num % RK2928_PULL_PINS_PER_REG;
|
|
}
|
|
|
|
#define RK3188_PULL_OFFSET 0x164
|
|
#define RK3188_PULL_BITS_PER_PIN 2
|
|
#define RK3188_PULL_PINS_PER_REG 8
|
|
#define RK3188_PULL_BANK_STRIDE 16
|
|
#define RK3188_PULL_PMU_OFFSET 0x64
|
|
|
|
static void rk3188_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 12 pins of the first bank are located elsewhere */
|
|
if (bank->bank_num == 0 && pin_num < 12) {
|
|
*regmap = info->regmap_pmu ? info->regmap_pmu
|
|
: bank->regmap_pull;
|
|
*reg = info->regmap_pmu ? RK3188_PULL_PMU_OFFSET : 0;
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
*bit = pin_num % RK3188_PULL_PINS_PER_REG;
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
} else {
|
|
*regmap = info->regmap_pull ? info->regmap_pull
|
|
: info->regmap_base;
|
|
*reg = info->regmap_pull ? 0 : RK3188_PULL_OFFSET;
|
|
|
|
/* correct the offset, as it is the 2nd pull register */
|
|
*reg -= 4;
|
|
*reg += bank->bank_num * RK3188_PULL_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
|
|
/*
|
|
* The bits in these registers have an inverse ordering
|
|
* with the lowest pin being in bits 15:14 and the highest
|
|
* pin in bits 1:0
|
|
*/
|
|
*bit = 7 - (pin_num % RK3188_PULL_PINS_PER_REG);
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
}
|
|
}
|
|
|
|
#define RK3288_PULL_OFFSET 0x140
|
|
static void rk3288_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 24 pins of the first bank are located in PMU */
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = RK3188_PULL_PMU_OFFSET;
|
|
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
*bit = pin_num % RK3188_PULL_PINS_PER_REG;
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3288_PULL_OFFSET;
|
|
|
|
/* correct the offset, as we're starting with the 2nd bank */
|
|
*reg -= 0x10;
|
|
*reg += bank->bank_num * RK3188_PULL_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
|
|
*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
}
|
|
}
|
|
|
|
#define RK3288_DRV_PMU_OFFSET 0x70
|
|
#define RK3288_DRV_GRF_OFFSET 0x1c0
|
|
#define RK3288_DRV_BITS_PER_PIN 2
|
|
#define RK3288_DRV_PINS_PER_REG 8
|
|
#define RK3288_DRV_BANK_STRIDE 16
|
|
|
|
static void rk3288_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 24 pins of the first bank are located in PMU */
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = RK3288_DRV_PMU_OFFSET;
|
|
|
|
*reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4);
|
|
*bit = pin_num % RK3288_DRV_PINS_PER_REG;
|
|
*bit *= RK3288_DRV_BITS_PER_PIN;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3288_DRV_GRF_OFFSET;
|
|
|
|
/* correct the offset, as we're starting with the 2nd bank */
|
|
*reg -= 0x10;
|
|
*reg += bank->bank_num * RK3288_DRV_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4);
|
|
|
|
*bit = (pin_num % RK3288_DRV_PINS_PER_REG);
|
|
*bit *= RK3288_DRV_BITS_PER_PIN;
|
|
}
|
|
}
|
|
|
|
#define RK3228_PULL_OFFSET 0x100
|
|
|
|
static void rk3228_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3228_PULL_OFFSET;
|
|
*reg += bank->bank_num * RK3188_PULL_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
|
|
*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
}
|
|
|
|
#define RK3228_DRV_GRF_OFFSET 0x200
|
|
|
|
static void rk3228_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3228_DRV_GRF_OFFSET;
|
|
*reg += bank->bank_num * RK3288_DRV_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4);
|
|
|
|
*bit = (pin_num % RK3288_DRV_PINS_PER_REG);
|
|
*bit *= RK3288_DRV_BITS_PER_PIN;
|
|
}
|
|
|
|
#define RK3368_PULL_GRF_OFFSET 0x100
|
|
#define RK3368_PULL_PMU_OFFSET 0x10
|
|
|
|
static void rk3368_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 32 pins of the first bank are located in PMU */
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = RK3368_PULL_PMU_OFFSET;
|
|
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
*bit = pin_num % RK3188_PULL_PINS_PER_REG;
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3368_PULL_GRF_OFFSET;
|
|
|
|
/* correct the offset, as we're starting with the 2nd bank */
|
|
*reg -= 0x10;
|
|
*reg += bank->bank_num * RK3188_PULL_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
|
|
*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
}
|
|
}
|
|
|
|
#define RK3368_DRV_PMU_OFFSET 0x20
|
|
#define RK3368_DRV_GRF_OFFSET 0x200
|
|
|
|
static void rk3368_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The first 32 pins of the first bank are located in PMU */
|
|
if (bank->bank_num == 0) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = RK3368_DRV_PMU_OFFSET;
|
|
|
|
*reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4);
|
|
*bit = pin_num % RK3288_DRV_PINS_PER_REG;
|
|
*bit *= RK3288_DRV_BITS_PER_PIN;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3368_DRV_GRF_OFFSET;
|
|
|
|
/* correct the offset, as we're starting with the 2nd bank */
|
|
*reg -= 0x10;
|
|
*reg += bank->bank_num * RK3288_DRV_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4);
|
|
|
|
*bit = (pin_num % RK3288_DRV_PINS_PER_REG);
|
|
*bit *= RK3288_DRV_BITS_PER_PIN;
|
|
}
|
|
}
|
|
|
|
#define RK3399_PULL_GRF_OFFSET 0xe040
|
|
#define RK3399_PULL_PMU_OFFSET 0x40
|
|
#define RK3399_DRV_3BITS_PER_PIN 3
|
|
|
|
static void rk3399_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
/* The bank0:16 and bank1:32 pins are located in PMU */
|
|
if ((bank->bank_num == 0) || (bank->bank_num == 1)) {
|
|
*regmap = info->regmap_pmu;
|
|
*reg = RK3399_PULL_PMU_OFFSET;
|
|
|
|
*reg += bank->bank_num * RK3188_PULL_BANK_STRIDE;
|
|
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
*bit = pin_num % RK3188_PULL_PINS_PER_REG;
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
} else {
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3399_PULL_GRF_OFFSET;
|
|
|
|
/* correct the offset, as we're starting with the 3rd bank */
|
|
*reg -= 0x20;
|
|
*reg += bank->bank_num * RK3188_PULL_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
|
|
|
|
*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
|
|
*bit *= RK3188_PULL_BITS_PER_PIN;
|
|
}
|
|
}
|
|
|
|
static void rk3399_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num, struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
int drv_num = (pin_num / 8);
|
|
|
|
/* The bank0:16 and bank1:32 pins are located in PMU */
|
|
if ((bank->bank_num == 0) || (bank->bank_num == 1))
|
|
*regmap = info->regmap_pmu;
|
|
else
|
|
*regmap = info->regmap_base;
|
|
|
|
*reg = bank->drv[drv_num].offset;
|
|
if ((bank->drv[drv_num].drv_type == DRV_TYPE_IO_1V8_3V0_AUTO) ||
|
|
(bank->drv[drv_num].drv_type == DRV_TYPE_IO_3V3_ONLY))
|
|
*bit = (pin_num % 8) * 3;
|
|
else
|
|
*bit = (pin_num % 8) * 2;
|
|
}
|
|
|
|
static int rockchip_perpin_drv_list[DRV_TYPE_MAX][8] = {
|
|
{ 2, 4, 8, 12, -1, -1, -1, -1 },
|
|
{ 3, 6, 9, 12, -1, -1, -1, -1 },
|
|
{ 5, 10, 15, 20, -1, -1, -1, -1 },
|
|
{ 4, 6, 8, 10, 12, 14, 16, 18 },
|
|
{ 4, 7, 10, 13, 16, 19, 22, 26 }
|
|
};
|
|
|
|
static int rockchip_get_drive_perpin(struct rockchip_pin_bank *bank,
|
|
int pin_num)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct regmap *regmap;
|
|
int reg, ret;
|
|
u32 data, temp, rmask_bits;
|
|
u8 bit;
|
|
int drv_type = bank->drv[pin_num / 8].drv_type;
|
|
|
|
ctrl->drv_calc_reg(bank, pin_num, ®map, ®, &bit);
|
|
|
|
switch (drv_type) {
|
|
case DRV_TYPE_IO_1V8_3V0_AUTO:
|
|
case DRV_TYPE_IO_3V3_ONLY:
|
|
rmask_bits = RK3399_DRV_3BITS_PER_PIN;
|
|
switch (bit) {
|
|
case 0 ... 12:
|
|
/* regular case, nothing to do */
|
|
break;
|
|
case 15:
|
|
/*
|
|
* drive-strength offset is special, as it is
|
|
* spread over 2 registers
|
|
*/
|
|
ret = regmap_read(regmap, reg, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = regmap_read(regmap, reg + 0x4, &temp);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/*
|
|
* the bit data[15] contains bit 0 of the value
|
|
* while temp[1:0] contains bits 2 and 1
|
|
*/
|
|
data >>= 15;
|
|
temp &= 0x3;
|
|
temp <<= 1;
|
|
data |= temp;
|
|
|
|
return rockchip_perpin_drv_list[drv_type][data];
|
|
case 18 ... 21:
|
|
/* setting fully enclosed in the second register */
|
|
reg += 4;
|
|
bit -= 16;
|
|
break;
|
|
default:
|
|
dev_err(info->dev, "unsupported bit: %d for pinctrl drive type: %d\n",
|
|
bit, drv_type);
|
|
return -EINVAL;
|
|
}
|
|
|
|
break;
|
|
case DRV_TYPE_IO_DEFAULT:
|
|
case DRV_TYPE_IO_1V8_OR_3V0:
|
|
case DRV_TYPE_IO_1V8_ONLY:
|
|
rmask_bits = RK3288_DRV_BITS_PER_PIN;
|
|
break;
|
|
default:
|
|
dev_err(info->dev, "unsupported pinctrl drive type: %d\n",
|
|
drv_type);
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = regmap_read(regmap, reg, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
data >>= bit;
|
|
data &= (1 << rmask_bits) - 1;
|
|
|
|
return rockchip_perpin_drv_list[drv_type][data];
|
|
}
|
|
|
|
static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank,
|
|
int pin_num, int strength)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct regmap *regmap;
|
|
int reg, ret, i;
|
|
u32 data, rmask, rmask_bits, temp;
|
|
u8 bit;
|
|
int drv_type = bank->drv[pin_num / 8].drv_type;
|
|
|
|
dev_dbg(info->dev, "setting drive of GPIO%d-%d to %d\n",
|
|
bank->bank_num, pin_num, strength);
|
|
|
|
ctrl->drv_calc_reg(bank, pin_num, ®map, ®, &bit);
|
|
|
|
ret = -EINVAL;
|
|
for (i = 0; i < ARRAY_SIZE(rockchip_perpin_drv_list[drv_type]); i++) {
|
|
if (rockchip_perpin_drv_list[drv_type][i] == strength) {
|
|
ret = i;
|
|
break;
|
|
} else if (rockchip_perpin_drv_list[drv_type][i] < 0) {
|
|
ret = rockchip_perpin_drv_list[drv_type][i];
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (ret < 0) {
|
|
dev_err(info->dev, "unsupported driver strength %d\n",
|
|
strength);
|
|
return ret;
|
|
}
|
|
|
|
switch (drv_type) {
|
|
case DRV_TYPE_IO_1V8_3V0_AUTO:
|
|
case DRV_TYPE_IO_3V3_ONLY:
|
|
rmask_bits = RK3399_DRV_3BITS_PER_PIN;
|
|
switch (bit) {
|
|
case 0 ... 12:
|
|
/* regular case, nothing to do */
|
|
break;
|
|
case 15:
|
|
/*
|
|
* drive-strength offset is special, as it is spread
|
|
* over 2 registers, the bit data[15] contains bit 0
|
|
* of the value while temp[1:0] contains bits 2 and 1
|
|
*/
|
|
data = (ret & 0x1) << 15;
|
|
temp = (ret >> 0x1) & 0x3;
|
|
|
|
rmask = BIT(15) | BIT(31);
|
|
data |= BIT(31);
|
|
ret = regmap_update_bits(regmap, reg, rmask, data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
rmask = 0x3 | (0x3 << 16);
|
|
temp |= (0x3 << 16);
|
|
reg += 0x4;
|
|
ret = regmap_update_bits(regmap, reg, rmask, temp);
|
|
|
|
return ret;
|
|
case 18 ... 21:
|
|
/* setting fully enclosed in the second register */
|
|
reg += 4;
|
|
bit -= 16;
|
|
break;
|
|
default:
|
|
dev_err(info->dev, "unsupported bit: %d for pinctrl drive type: %d\n",
|
|
bit, drv_type);
|
|
return -EINVAL;
|
|
}
|
|
break;
|
|
case DRV_TYPE_IO_DEFAULT:
|
|
case DRV_TYPE_IO_1V8_OR_3V0:
|
|
case DRV_TYPE_IO_1V8_ONLY:
|
|
rmask_bits = RK3288_DRV_BITS_PER_PIN;
|
|
break;
|
|
default:
|
|
dev_err(info->dev, "unsupported pinctrl drive type: %d\n",
|
|
drv_type);
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* enable the write to the equivalent lower bits */
|
|
data = ((1 << rmask_bits) - 1) << (bit + 16);
|
|
rmask = data | (data >> 16);
|
|
data |= (ret << bit);
|
|
|
|
ret = regmap_update_bits(regmap, reg, rmask, data);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int rockchip_pull_list[PULL_TYPE_MAX][4] = {
|
|
{
|
|
PIN_CONFIG_BIAS_DISABLE,
|
|
PIN_CONFIG_BIAS_PULL_UP,
|
|
PIN_CONFIG_BIAS_PULL_DOWN,
|
|
PIN_CONFIG_BIAS_BUS_HOLD
|
|
},
|
|
{
|
|
PIN_CONFIG_BIAS_DISABLE,
|
|
PIN_CONFIG_BIAS_PULL_DOWN,
|
|
PIN_CONFIG_BIAS_DISABLE,
|
|
PIN_CONFIG_BIAS_PULL_UP
|
|
},
|
|
};
|
|
|
|
static int rockchip_get_pull(struct rockchip_pin_bank *bank, int pin_num)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct regmap *regmap;
|
|
int reg, ret, pull_type;
|
|
u8 bit;
|
|
u32 data;
|
|
|
|
/* rk3066b does support any pulls */
|
|
if (ctrl->type == RK3066B)
|
|
return PIN_CONFIG_BIAS_DISABLE;
|
|
|
|
ctrl->pull_calc_reg(bank, pin_num, ®map, ®, &bit);
|
|
|
|
ret = regmap_read(regmap, reg, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
switch (ctrl->type) {
|
|
case RK2928:
|
|
case RK3128:
|
|
return !(data & BIT(bit))
|
|
? PIN_CONFIG_BIAS_PULL_PIN_DEFAULT
|
|
: PIN_CONFIG_BIAS_DISABLE;
|
|
case PX30:
|
|
case RV1108:
|
|
case RK3188:
|
|
case RK3288:
|
|
case RK3368:
|
|
case RK3399:
|
|
pull_type = bank->pull_type[pin_num / 8];
|
|
data >>= bit;
|
|
data &= (1 << RK3188_PULL_BITS_PER_PIN) - 1;
|
|
|
|
return rockchip_pull_list[pull_type][data];
|
|
default:
|
|
dev_err(info->dev, "unsupported pinctrl type\n");
|
|
return -EINVAL;
|
|
};
|
|
}
|
|
|
|
static int rockchip_set_pull(struct rockchip_pin_bank *bank,
|
|
int pin_num, int pull)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct regmap *regmap;
|
|
int reg, ret, i, pull_type;
|
|
u8 bit;
|
|
u32 data, rmask;
|
|
|
|
dev_dbg(info->dev, "setting pull of GPIO%d-%d to %d\n",
|
|
bank->bank_num, pin_num, pull);
|
|
|
|
/* rk3066b does support any pulls */
|
|
if (ctrl->type == RK3066B)
|
|
return pull ? -EINVAL : 0;
|
|
|
|
ctrl->pull_calc_reg(bank, pin_num, ®map, ®, &bit);
|
|
|
|
switch (ctrl->type) {
|
|
case RK2928:
|
|
case RK3128:
|
|
data = BIT(bit + 16);
|
|
if (pull == PIN_CONFIG_BIAS_DISABLE)
|
|
data |= BIT(bit);
|
|
ret = regmap_write(regmap, reg, data);
|
|
break;
|
|
case PX30:
|
|
case RV1108:
|
|
case RK3188:
|
|
case RK3288:
|
|
case RK3368:
|
|
case RK3399:
|
|
pull_type = bank->pull_type[pin_num / 8];
|
|
ret = -EINVAL;
|
|
for (i = 0; i < ARRAY_SIZE(rockchip_pull_list[pull_type]);
|
|
i++) {
|
|
if (rockchip_pull_list[pull_type][i] == pull) {
|
|
ret = i;
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (ret < 0) {
|
|
dev_err(info->dev, "unsupported pull setting %d\n",
|
|
pull);
|
|
return ret;
|
|
}
|
|
|
|
/* enable the write to the equivalent lower bits */
|
|
data = ((1 << RK3188_PULL_BITS_PER_PIN) - 1) << (bit + 16);
|
|
rmask = data | (data >> 16);
|
|
data |= (ret << bit);
|
|
|
|
ret = regmap_update_bits(regmap, reg, rmask, data);
|
|
break;
|
|
default:
|
|
dev_err(info->dev, "unsupported pinctrl type\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
#define RK3328_SCHMITT_BITS_PER_PIN 1
|
|
#define RK3328_SCHMITT_PINS_PER_REG 16
|
|
#define RK3328_SCHMITT_BANK_STRIDE 8
|
|
#define RK3328_SCHMITT_GRF_OFFSET 0x380
|
|
|
|
static int rk3328_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
|
|
int pin_num,
|
|
struct regmap **regmap,
|
|
int *reg, u8 *bit)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
|
|
*regmap = info->regmap_base;
|
|
*reg = RK3328_SCHMITT_GRF_OFFSET;
|
|
|
|
*reg += bank->bank_num * RK3328_SCHMITT_BANK_STRIDE;
|
|
*reg += ((pin_num / RK3328_SCHMITT_PINS_PER_REG) * 4);
|
|
*bit = pin_num % RK3328_SCHMITT_PINS_PER_REG;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_get_schmitt(struct rockchip_pin_bank *bank, int pin_num)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct regmap *regmap;
|
|
int reg, ret;
|
|
u8 bit;
|
|
u32 data;
|
|
|
|
ret = ctrl->schmitt_calc_reg(bank, pin_num, ®map, ®, &bit);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = regmap_read(regmap, reg, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
data >>= bit;
|
|
return data & 0x1;
|
|
}
|
|
|
|
static int rockchip_set_schmitt(struct rockchip_pin_bank *bank,
|
|
int pin_num, int enable)
|
|
{
|
|
struct rockchip_pinctrl *info = bank->drvdata;
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct regmap *regmap;
|
|
int reg, ret;
|
|
u8 bit;
|
|
u32 data, rmask;
|
|
|
|
dev_dbg(info->dev, "setting input schmitt of GPIO%d-%d to %d\n",
|
|
bank->bank_num, pin_num, enable);
|
|
|
|
ret = ctrl->schmitt_calc_reg(bank, pin_num, ®map, ®, &bit);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* enable the write to the equivalent lower bits */
|
|
data = BIT(bit + 16) | (enable << bit);
|
|
rmask = BIT(bit + 16) | BIT(bit);
|
|
|
|
return regmap_update_bits(regmap, reg, rmask, data);
|
|
}
|
|
|
|
/*
|
|
* Pinmux_ops handling
|
|
*/
|
|
|
|
static int rockchip_pmx_get_funcs_count(struct pinctrl_dev *pctldev)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
return info->nfunctions;
|
|
}
|
|
|
|
static const char *rockchip_pmx_get_func_name(struct pinctrl_dev *pctldev,
|
|
unsigned selector)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
return info->functions[selector].name;
|
|
}
|
|
|
|
static int rockchip_pmx_get_groups(struct pinctrl_dev *pctldev,
|
|
unsigned selector, const char * const **groups,
|
|
unsigned * const num_groups)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
|
|
*groups = info->functions[selector].groups;
|
|
*num_groups = info->functions[selector].ngroups;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_pmx_set(struct pinctrl_dev *pctldev, unsigned selector,
|
|
unsigned group)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
const unsigned int *pins = info->groups[group].pins;
|
|
const struct rockchip_pin_config *data = info->groups[group].data;
|
|
struct rockchip_pin_bank *bank;
|
|
int cnt, ret = 0;
|
|
|
|
dev_dbg(info->dev, "enable function %s group %s\n",
|
|
info->functions[selector].name, info->groups[group].name);
|
|
|
|
/*
|
|
* for each pin in the pin group selected, program the corresponding
|
|
* pin function number in the config register.
|
|
*/
|
|
for (cnt = 0; cnt < info->groups[group].npins; cnt++) {
|
|
bank = pin_to_bank(info, pins[cnt]);
|
|
ret = rockchip_set_mux(bank, pins[cnt] - bank->pin_base,
|
|
data[cnt].func);
|
|
if (ret)
|
|
break;
|
|
}
|
|
|
|
if (ret) {
|
|
/* revert the already done pin settings */
|
|
for (cnt--; cnt >= 0; cnt--)
|
|
rockchip_set_mux(bank, pins[cnt] - bank->pin_base, 0);
|
|
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
|
|
{
|
|
struct rockchip_pin_bank *bank = gpiochip_get_data(chip);
|
|
u32 data;
|
|
int ret;
|
|
|
|
ret = clk_enable(bank->clk);
|
|
if (ret < 0) {
|
|
dev_err(bank->drvdata->dev,
|
|
"failed to enable clock for bank %s\n", bank->name);
|
|
return ret;
|
|
}
|
|
data = readl_relaxed(bank->reg_base + GPIO_SWPORT_DDR);
|
|
clk_disable(bank->clk);
|
|
|
|
return !(data & BIT(offset));
|
|
}
|
|
|
|
/*
|
|
* The calls to gpio_direction_output() and gpio_direction_input()
|
|
* leads to this function call (via the pinctrl_gpio_direction_{input|output}()
|
|
* function called from the gpiolib interface).
|
|
*/
|
|
static int _rockchip_pmx_gpio_set_direction(struct gpio_chip *chip,
|
|
int pin, bool input)
|
|
{
|
|
struct rockchip_pin_bank *bank;
|
|
int ret;
|
|
unsigned long flags;
|
|
u32 data;
|
|
|
|
bank = gpiochip_get_data(chip);
|
|
|
|
ret = rockchip_set_mux(bank, pin, RK_FUNC_GPIO);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
clk_enable(bank->clk);
|
|
raw_spin_lock_irqsave(&bank->slock, flags);
|
|
|
|
data = readl_relaxed(bank->reg_base + GPIO_SWPORT_DDR);
|
|
/* set bit to 1 for output, 0 for input */
|
|
if (!input)
|
|
data |= BIT(pin);
|
|
else
|
|
data &= ~BIT(pin);
|
|
writel_relaxed(data, bank->reg_base + GPIO_SWPORT_DDR);
|
|
|
|
raw_spin_unlock_irqrestore(&bank->slock, flags);
|
|
clk_disable(bank->clk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
|
|
struct pinctrl_gpio_range *range,
|
|
unsigned offset, bool input)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
struct gpio_chip *chip;
|
|
int pin;
|
|
|
|
chip = range->gc;
|
|
pin = offset - chip->base;
|
|
dev_dbg(info->dev, "gpio_direction for pin %u as %s-%d to %s\n",
|
|
offset, range->name, pin, input ? "input" : "output");
|
|
|
|
return _rockchip_pmx_gpio_set_direction(chip, offset - chip->base,
|
|
input);
|
|
}
|
|
|
|
static const struct pinmux_ops rockchip_pmx_ops = {
|
|
.get_functions_count = rockchip_pmx_get_funcs_count,
|
|
.get_function_name = rockchip_pmx_get_func_name,
|
|
.get_function_groups = rockchip_pmx_get_groups,
|
|
.set_mux = rockchip_pmx_set,
|
|
.gpio_set_direction = rockchip_pmx_gpio_set_direction,
|
|
};
|
|
|
|
/*
|
|
* Pinconf_ops handling
|
|
*/
|
|
|
|
static bool rockchip_pinconf_pull_valid(struct rockchip_pin_ctrl *ctrl,
|
|
enum pin_config_param pull)
|
|
{
|
|
switch (ctrl->type) {
|
|
case RK2928:
|
|
case RK3128:
|
|
return (pull == PIN_CONFIG_BIAS_PULL_PIN_DEFAULT ||
|
|
pull == PIN_CONFIG_BIAS_DISABLE);
|
|
case RK3066B:
|
|
return pull ? false : true;
|
|
case PX30:
|
|
case RV1108:
|
|
case RK3188:
|
|
case RK3288:
|
|
case RK3368:
|
|
case RK3399:
|
|
return (pull != PIN_CONFIG_BIAS_PULL_PIN_DEFAULT);
|
|
}
|
|
|
|
return false;
|
|
}
|
|
|
|
static void rockchip_gpio_set(struct gpio_chip *gc, unsigned offset, int value);
|
|
static int rockchip_gpio_get(struct gpio_chip *gc, unsigned offset);
|
|
|
|
/* set the pin config settings for a specified pin */
|
|
static int rockchip_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
|
|
unsigned long *configs, unsigned num_configs)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
struct rockchip_pin_bank *bank = pin_to_bank(info, pin);
|
|
enum pin_config_param param;
|
|
u32 arg;
|
|
int i;
|
|
int rc;
|
|
|
|
for (i = 0; i < num_configs; i++) {
|
|
param = pinconf_to_config_param(configs[i]);
|
|
arg = pinconf_to_config_argument(configs[i]);
|
|
|
|
switch (param) {
|
|
case PIN_CONFIG_BIAS_DISABLE:
|
|
rc = rockchip_set_pull(bank, pin - bank->pin_base,
|
|
param);
|
|
if (rc)
|
|
return rc;
|
|
break;
|
|
case PIN_CONFIG_BIAS_PULL_UP:
|
|
case PIN_CONFIG_BIAS_PULL_DOWN:
|
|
case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
|
|
case PIN_CONFIG_BIAS_BUS_HOLD:
|
|
if (!rockchip_pinconf_pull_valid(info->ctrl, param))
|
|
return -ENOTSUPP;
|
|
|
|
if (!arg)
|
|
return -EINVAL;
|
|
|
|
rc = rockchip_set_pull(bank, pin - bank->pin_base,
|
|
param);
|
|
if (rc)
|
|
return rc;
|
|
break;
|
|
case PIN_CONFIG_OUTPUT:
|
|
rockchip_gpio_set(&bank->gpio_chip,
|
|
pin - bank->pin_base, arg);
|
|
rc = _rockchip_pmx_gpio_set_direction(&bank->gpio_chip,
|
|
pin - bank->pin_base, false);
|
|
if (rc)
|
|
return rc;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_STRENGTH:
|
|
/* rk3288 is the first with per-pin drive-strength */
|
|
if (!info->ctrl->drv_calc_reg)
|
|
return -ENOTSUPP;
|
|
|
|
rc = rockchip_set_drive_perpin(bank,
|
|
pin - bank->pin_base, arg);
|
|
if (rc < 0)
|
|
return rc;
|
|
break;
|
|
case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
|
|
if (!info->ctrl->schmitt_calc_reg)
|
|
return -ENOTSUPP;
|
|
|
|
rc = rockchip_set_schmitt(bank,
|
|
pin - bank->pin_base, arg);
|
|
if (rc < 0)
|
|
return rc;
|
|
break;
|
|
default:
|
|
return -ENOTSUPP;
|
|
break;
|
|
}
|
|
} /* for each config */
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* get the pin config settings for a specified pin */
|
|
static int rockchip_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
|
|
unsigned long *config)
|
|
{
|
|
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
|
|
struct rockchip_pin_bank *bank = pin_to_bank(info, pin);
|
|
enum pin_config_param param = pinconf_to_config_param(*config);
|
|
u16 arg;
|
|
int rc;
|
|
|
|
switch (param) {
|
|
case PIN_CONFIG_BIAS_DISABLE:
|
|
if (rockchip_get_pull(bank, pin - bank->pin_base) != param)
|
|
return -EINVAL;
|
|
|
|
arg = 0;
|
|
break;
|
|
case PIN_CONFIG_BIAS_PULL_UP:
|
|
case PIN_CONFIG_BIAS_PULL_DOWN:
|
|
case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
|
|
case PIN_CONFIG_BIAS_BUS_HOLD:
|
|
if (!rockchip_pinconf_pull_valid(info->ctrl, param))
|
|
return -ENOTSUPP;
|
|
|
|
if (rockchip_get_pull(bank, pin - bank->pin_base) != param)
|
|
return -EINVAL;
|
|
|
|
arg = 1;
|
|
break;
|
|
case PIN_CONFIG_OUTPUT:
|
|
rc = rockchip_get_mux(bank, pin - bank->pin_base);
|
|
if (rc != RK_FUNC_GPIO)
|
|
return -EINVAL;
|
|
|
|
rc = rockchip_gpio_get(&bank->gpio_chip, pin - bank->pin_base);
|
|
if (rc < 0)
|
|
return rc;
|
|
|
|
arg = rc ? 1 : 0;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_STRENGTH:
|
|
/* rk3288 is the first with per-pin drive-strength */
|
|
if (!info->ctrl->drv_calc_reg)
|
|
return -ENOTSUPP;
|
|
|
|
rc = rockchip_get_drive_perpin(bank, pin - bank->pin_base);
|
|
if (rc < 0)
|
|
return rc;
|
|
|
|
arg = rc;
|
|
break;
|
|
case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
|
|
if (!info->ctrl->schmitt_calc_reg)
|
|
return -ENOTSUPP;
|
|
|
|
rc = rockchip_get_schmitt(bank, pin - bank->pin_base);
|
|
if (rc < 0)
|
|
return rc;
|
|
|
|
arg = rc;
|
|
break;
|
|
default:
|
|
return -ENOTSUPP;
|
|
break;
|
|
}
|
|
|
|
*config = pinconf_to_config_packed(param, arg);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct pinconf_ops rockchip_pinconf_ops = {
|
|
.pin_config_get = rockchip_pinconf_get,
|
|
.pin_config_set = rockchip_pinconf_set,
|
|
.is_generic = true,
|
|
};
|
|
|
|
static const struct of_device_id rockchip_bank_match[] = {
|
|
{ .compatible = "rockchip,gpio-bank" },
|
|
{ .compatible = "rockchip,rk3188-gpio-bank0" },
|
|
{},
|
|
};
|
|
|
|
static void rockchip_pinctrl_child_count(struct rockchip_pinctrl *info,
|
|
struct device_node *np)
|
|
{
|
|
struct device_node *child;
|
|
|
|
for_each_child_of_node(np, child) {
|
|
if (of_match_node(rockchip_bank_match, child))
|
|
continue;
|
|
|
|
info->nfunctions++;
|
|
info->ngroups += of_get_child_count(child);
|
|
}
|
|
}
|
|
|
|
static int rockchip_pinctrl_parse_groups(struct device_node *np,
|
|
struct rockchip_pin_group *grp,
|
|
struct rockchip_pinctrl *info,
|
|
u32 index)
|
|
{
|
|
struct rockchip_pin_bank *bank;
|
|
int size;
|
|
const __be32 *list;
|
|
int num;
|
|
int i, j;
|
|
int ret;
|
|
|
|
dev_dbg(info->dev, "group(%d): %pOFn\n", index, np);
|
|
|
|
/* Initialise group */
|
|
grp->name = np->name;
|
|
|
|
/*
|
|
* the binding format is rockchip,pins = <bank pin mux CONFIG>,
|
|
* do sanity check and calculate pins number
|
|
*/
|
|
list = of_get_property(np, "rockchip,pins", &size);
|
|
/* we do not check return since it's safe node passed down */
|
|
size /= sizeof(*list);
|
|
if (!size || size % 4) {
|
|
dev_err(info->dev, "wrong pins number or pins and configs should be by 4\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
grp->npins = size / 4;
|
|
|
|
grp->pins = devm_kcalloc(info->dev, grp->npins, sizeof(unsigned int),
|
|
GFP_KERNEL);
|
|
grp->data = devm_kcalloc(info->dev,
|
|
grp->npins,
|
|
sizeof(struct rockchip_pin_config),
|
|
GFP_KERNEL);
|
|
if (!grp->pins || !grp->data)
|
|
return -ENOMEM;
|
|
|
|
for (i = 0, j = 0; i < size; i += 4, j++) {
|
|
const __be32 *phandle;
|
|
struct device_node *np_config;
|
|
|
|
num = be32_to_cpu(*list++);
|
|
bank = bank_num_to_bank(info, num);
|
|
if (IS_ERR(bank))
|
|
return PTR_ERR(bank);
|
|
|
|
grp->pins[j] = bank->pin_base + be32_to_cpu(*list++);
|
|
grp->data[j].func = be32_to_cpu(*list++);
|
|
|
|
phandle = list++;
|
|
if (!phandle)
|
|
return -EINVAL;
|
|
|
|
np_config = of_find_node_by_phandle(be32_to_cpup(phandle));
|
|
ret = pinconf_generic_parse_dt_config(np_config, NULL,
|
|
&grp->data[j].configs, &grp->data[j].nconfigs);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_pinctrl_parse_functions(struct device_node *np,
|
|
struct rockchip_pinctrl *info,
|
|
u32 index)
|
|
{
|
|
struct device_node *child;
|
|
struct rockchip_pmx_func *func;
|
|
struct rockchip_pin_group *grp;
|
|
int ret;
|
|
static u32 grp_index;
|
|
u32 i = 0;
|
|
|
|
dev_dbg(info->dev, "parse function(%d): %pOFn\n", index, np);
|
|
|
|
func = &info->functions[index];
|
|
|
|
/* Initialise function */
|
|
func->name = np->name;
|
|
func->ngroups = of_get_child_count(np);
|
|
if (func->ngroups <= 0)
|
|
return 0;
|
|
|
|
func->groups = devm_kcalloc(info->dev,
|
|
func->ngroups, sizeof(char *), GFP_KERNEL);
|
|
if (!func->groups)
|
|
return -ENOMEM;
|
|
|
|
for_each_child_of_node(np, child) {
|
|
func->groups[i] = child->name;
|
|
grp = &info->groups[grp_index++];
|
|
ret = rockchip_pinctrl_parse_groups(child, grp, info, i++);
|
|
if (ret) {
|
|
of_node_put(child);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_pinctrl_parse_dt(struct platform_device *pdev,
|
|
struct rockchip_pinctrl *info)
|
|
{
|
|
struct device *dev = &pdev->dev;
|
|
struct device_node *np = dev->of_node;
|
|
struct device_node *child;
|
|
int ret;
|
|
int i;
|
|
|
|
rockchip_pinctrl_child_count(info, np);
|
|
|
|
dev_dbg(&pdev->dev, "nfunctions = %d\n", info->nfunctions);
|
|
dev_dbg(&pdev->dev, "ngroups = %d\n", info->ngroups);
|
|
|
|
info->functions = devm_kcalloc(dev,
|
|
info->nfunctions,
|
|
sizeof(struct rockchip_pmx_func),
|
|
GFP_KERNEL);
|
|
if (!info->functions)
|
|
return -EINVAL;
|
|
|
|
info->groups = devm_kcalloc(dev,
|
|
info->ngroups,
|
|
sizeof(struct rockchip_pin_group),
|
|
GFP_KERNEL);
|
|
if (!info->groups)
|
|
return -EINVAL;
|
|
|
|
i = 0;
|
|
|
|
for_each_child_of_node(np, child) {
|
|
if (of_match_node(rockchip_bank_match, child))
|
|
continue;
|
|
|
|
ret = rockchip_pinctrl_parse_functions(child, info, i++);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to parse function\n");
|
|
of_node_put(child);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_pinctrl_register(struct platform_device *pdev,
|
|
struct rockchip_pinctrl *info)
|
|
{
|
|
struct pinctrl_desc *ctrldesc = &info->pctl;
|
|
struct pinctrl_pin_desc *pindesc, *pdesc;
|
|
struct rockchip_pin_bank *pin_bank;
|
|
int pin, bank, ret;
|
|
int k;
|
|
|
|
ctrldesc->name = "rockchip-pinctrl";
|
|
ctrldesc->owner = THIS_MODULE;
|
|
ctrldesc->pctlops = &rockchip_pctrl_ops;
|
|
ctrldesc->pmxops = &rockchip_pmx_ops;
|
|
ctrldesc->confops = &rockchip_pinconf_ops;
|
|
|
|
pindesc = devm_kcalloc(&pdev->dev,
|
|
info->ctrl->nr_pins, sizeof(*pindesc),
|
|
GFP_KERNEL);
|
|
if (!pindesc)
|
|
return -ENOMEM;
|
|
|
|
ctrldesc->pins = pindesc;
|
|
ctrldesc->npins = info->ctrl->nr_pins;
|
|
|
|
pdesc = pindesc;
|
|
for (bank = 0 , k = 0; bank < info->ctrl->nr_banks; bank++) {
|
|
pin_bank = &info->ctrl->pin_banks[bank];
|
|
for (pin = 0; pin < pin_bank->nr_pins; pin++, k++) {
|
|
pdesc->number = k;
|
|
pdesc->name = kasprintf(GFP_KERNEL, "%s-%d",
|
|
pin_bank->name, pin);
|
|
pdesc++;
|
|
}
|
|
}
|
|
|
|
ret = rockchip_pinctrl_parse_dt(pdev, info);
|
|
if (ret)
|
|
return ret;
|
|
|
|
info->pctl_dev = devm_pinctrl_register(&pdev->dev, ctrldesc, info);
|
|
if (IS_ERR(info->pctl_dev)) {
|
|
dev_err(&pdev->dev, "could not register pinctrl driver\n");
|
|
return PTR_ERR(info->pctl_dev);
|
|
}
|
|
|
|
for (bank = 0; bank < info->ctrl->nr_banks; ++bank) {
|
|
pin_bank = &info->ctrl->pin_banks[bank];
|
|
pin_bank->grange.name = pin_bank->name;
|
|
pin_bank->grange.id = bank;
|
|
pin_bank->grange.pin_base = pin_bank->pin_base;
|
|
pin_bank->grange.base = pin_bank->gpio_chip.base;
|
|
pin_bank->grange.npins = pin_bank->gpio_chip.ngpio;
|
|
pin_bank->grange.gc = &pin_bank->gpio_chip;
|
|
pinctrl_add_gpio_range(info->pctl_dev, &pin_bank->grange);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* GPIO handling
|
|
*/
|
|
|
|
static void rockchip_gpio_set(struct gpio_chip *gc, unsigned offset, int value)
|
|
{
|
|
struct rockchip_pin_bank *bank = gpiochip_get_data(gc);
|
|
void __iomem *reg = bank->reg_base + GPIO_SWPORT_DR;
|
|
unsigned long flags;
|
|
u32 data;
|
|
|
|
clk_enable(bank->clk);
|
|
raw_spin_lock_irqsave(&bank->slock, flags);
|
|
|
|
data = readl(reg);
|
|
data &= ~BIT(offset);
|
|
if (value)
|
|
data |= BIT(offset);
|
|
writel(data, reg);
|
|
|
|
raw_spin_unlock_irqrestore(&bank->slock, flags);
|
|
clk_disable(bank->clk);
|
|
}
|
|
|
|
/*
|
|
* Returns the level of the pin for input direction and setting of the DR
|
|
* register for output gpios.
|
|
*/
|
|
static int rockchip_gpio_get(struct gpio_chip *gc, unsigned offset)
|
|
{
|
|
struct rockchip_pin_bank *bank = gpiochip_get_data(gc);
|
|
u32 data;
|
|
|
|
clk_enable(bank->clk);
|
|
data = readl(bank->reg_base + GPIO_EXT_PORT);
|
|
clk_disable(bank->clk);
|
|
data >>= offset;
|
|
data &= 1;
|
|
return data;
|
|
}
|
|
|
|
/*
|
|
* gpiolib gpio_direction_input callback function. The setting of the pin
|
|
* mux function as 'gpio input' will be handled by the pinctrl subsystem
|
|
* interface.
|
|
*/
|
|
static int rockchip_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
|
|
{
|
|
return pinctrl_gpio_direction_input(gc->base + offset);
|
|
}
|
|
|
|
/*
|
|
* gpiolib gpio_direction_output callback function. The setting of the pin
|
|
* mux function as 'gpio output' will be handled by the pinctrl subsystem
|
|
* interface.
|
|
*/
|
|
static int rockchip_gpio_direction_output(struct gpio_chip *gc,
|
|
unsigned offset, int value)
|
|
{
|
|
rockchip_gpio_set(gc, offset, value);
|
|
return pinctrl_gpio_direction_output(gc->base + offset);
|
|
}
|
|
|
|
static void rockchip_gpio_set_debounce(struct gpio_chip *gc,
|
|
unsigned int offset, bool enable)
|
|
{
|
|
struct rockchip_pin_bank *bank = gpiochip_get_data(gc);
|
|
void __iomem *reg = bank->reg_base + GPIO_DEBOUNCE;
|
|
unsigned long flags;
|
|
u32 data;
|
|
|
|
clk_enable(bank->clk);
|
|
raw_spin_lock_irqsave(&bank->slock, flags);
|
|
|
|
data = readl(reg);
|
|
if (enable)
|
|
data |= BIT(offset);
|
|
else
|
|
data &= ~BIT(offset);
|
|
writel(data, reg);
|
|
|
|
raw_spin_unlock_irqrestore(&bank->slock, flags);
|
|
clk_disable(bank->clk);
|
|
}
|
|
|
|
/*
|
|
* gpiolib set_config callback function. The setting of the pin
|
|
* mux function as 'gpio output' will be handled by the pinctrl subsystem
|
|
* interface.
|
|
*/
|
|
static int rockchip_gpio_set_config(struct gpio_chip *gc, unsigned int offset,
|
|
unsigned long config)
|
|
{
|
|
enum pin_config_param param = pinconf_to_config_param(config);
|
|
|
|
switch (param) {
|
|
case PIN_CONFIG_INPUT_DEBOUNCE:
|
|
rockchip_gpio_set_debounce(gc, offset, true);
|
|
/*
|
|
* Rockchip's gpio could only support up to one period
|
|
* of the debounce clock(pclk), which is far away from
|
|
* satisftying the requirement, as pclk is usually near
|
|
* 100MHz shared by all peripherals. So the fact is it
|
|
* has crippled debounce capability could only be useful
|
|
* to prevent any spurious glitches from waking up the system
|
|
* if the gpio is conguired as wakeup interrupt source. Let's
|
|
* still return -ENOTSUPP as before, to make sure the caller
|
|
* of gpiod_set_debounce won't change its behaviour.
|
|
*/
|
|
default:
|
|
return -ENOTSUPP;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* gpiolib gpio_to_irq callback function. Creates a mapping between a GPIO pin
|
|
* and a virtual IRQ, if not already present.
|
|
*/
|
|
static int rockchip_gpio_to_irq(struct gpio_chip *gc, unsigned offset)
|
|
{
|
|
struct rockchip_pin_bank *bank = gpiochip_get_data(gc);
|
|
unsigned int virq;
|
|
|
|
if (!bank->domain)
|
|
return -ENXIO;
|
|
|
|
virq = irq_create_mapping(bank->domain, offset);
|
|
|
|
return (virq) ? : -ENXIO;
|
|
}
|
|
|
|
static const struct gpio_chip rockchip_gpiolib_chip = {
|
|
.request = gpiochip_generic_request,
|
|
.free = gpiochip_generic_free,
|
|
.set = rockchip_gpio_set,
|
|
.get = rockchip_gpio_get,
|
|
.get_direction = rockchip_gpio_get_direction,
|
|
.direction_input = rockchip_gpio_direction_input,
|
|
.direction_output = rockchip_gpio_direction_output,
|
|
.set_config = rockchip_gpio_set_config,
|
|
.to_irq = rockchip_gpio_to_irq,
|
|
.owner = THIS_MODULE,
|
|
};
|
|
|
|
/*
|
|
* Interrupt handling
|
|
*/
|
|
|
|
static void rockchip_irq_demux(struct irq_desc *desc)
|
|
{
|
|
struct irq_chip *chip = irq_desc_get_chip(desc);
|
|
struct rockchip_pin_bank *bank = irq_desc_get_handler_data(desc);
|
|
u32 pend;
|
|
|
|
dev_dbg(bank->drvdata->dev, "got irq for bank %s\n", bank->name);
|
|
|
|
chained_irq_enter(chip, desc);
|
|
|
|
pend = readl_relaxed(bank->reg_base + GPIO_INT_STATUS);
|
|
|
|
while (pend) {
|
|
unsigned int irq, virq;
|
|
|
|
irq = __ffs(pend);
|
|
pend &= ~BIT(irq);
|
|
virq = irq_linear_revmap(bank->domain, irq);
|
|
|
|
if (!virq) {
|
|
dev_err(bank->drvdata->dev, "unmapped irq %d\n", irq);
|
|
continue;
|
|
}
|
|
|
|
dev_dbg(bank->drvdata->dev, "handling irq %d\n", irq);
|
|
|
|
/*
|
|
* Triggering IRQ on both rising and falling edge
|
|
* needs manual intervention.
|
|
*/
|
|
if (bank->toggle_edge_mode & BIT(irq)) {
|
|
u32 data, data_old, polarity;
|
|
unsigned long flags;
|
|
|
|
data = readl_relaxed(bank->reg_base + GPIO_EXT_PORT);
|
|
do {
|
|
raw_spin_lock_irqsave(&bank->slock, flags);
|
|
|
|
polarity = readl_relaxed(bank->reg_base +
|
|
GPIO_INT_POLARITY);
|
|
if (data & BIT(irq))
|
|
polarity &= ~BIT(irq);
|
|
else
|
|
polarity |= BIT(irq);
|
|
writel(polarity,
|
|
bank->reg_base + GPIO_INT_POLARITY);
|
|
|
|
raw_spin_unlock_irqrestore(&bank->slock, flags);
|
|
|
|
data_old = data;
|
|
data = readl_relaxed(bank->reg_base +
|
|
GPIO_EXT_PORT);
|
|
} while ((data & BIT(irq)) != (data_old & BIT(irq)));
|
|
}
|
|
|
|
generic_handle_irq(virq);
|
|
}
|
|
|
|
chained_irq_exit(chip, desc);
|
|
}
|
|
|
|
static int rockchip_irq_set_type(struct irq_data *d, unsigned int type)
|
|
{
|
|
struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
|
|
struct rockchip_pin_bank *bank = gc->private;
|
|
u32 mask = BIT(d->hwirq);
|
|
u32 polarity;
|
|
u32 level;
|
|
u32 data;
|
|
unsigned long flags;
|
|
int ret;
|
|
|
|
/* make sure the pin is configured as gpio input */
|
|
ret = rockchip_set_mux(bank, d->hwirq, RK_FUNC_GPIO);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
clk_enable(bank->clk);
|
|
raw_spin_lock_irqsave(&bank->slock, flags);
|
|
|
|
data = readl_relaxed(bank->reg_base + GPIO_SWPORT_DDR);
|
|
data &= ~mask;
|
|
writel_relaxed(data, bank->reg_base + GPIO_SWPORT_DDR);
|
|
|
|
raw_spin_unlock_irqrestore(&bank->slock, flags);
|
|
|
|
if (type & IRQ_TYPE_EDGE_BOTH)
|
|
irq_set_handler_locked(d, handle_edge_irq);
|
|
else
|
|
irq_set_handler_locked(d, handle_level_irq);
|
|
|
|
raw_spin_lock_irqsave(&bank->slock, flags);
|
|
irq_gc_lock(gc);
|
|
|
|
level = readl_relaxed(gc->reg_base + GPIO_INTTYPE_LEVEL);
|
|
polarity = readl_relaxed(gc->reg_base + GPIO_INT_POLARITY);
|
|
|
|
switch (type) {
|
|
case IRQ_TYPE_EDGE_BOTH:
|
|
bank->toggle_edge_mode |= mask;
|
|
level |= mask;
|
|
|
|
/*
|
|
* Determine gpio state. If 1 next interrupt should be falling
|
|
* otherwise rising.
|
|
*/
|
|
data = readl(bank->reg_base + GPIO_EXT_PORT);
|
|
if (data & mask)
|
|
polarity &= ~mask;
|
|
else
|
|
polarity |= mask;
|
|
break;
|
|
case IRQ_TYPE_EDGE_RISING:
|
|
bank->toggle_edge_mode &= ~mask;
|
|
level |= mask;
|
|
polarity |= mask;
|
|
break;
|
|
case IRQ_TYPE_EDGE_FALLING:
|
|
bank->toggle_edge_mode &= ~mask;
|
|
level |= mask;
|
|
polarity &= ~mask;
|
|
break;
|
|
case IRQ_TYPE_LEVEL_HIGH:
|
|
bank->toggle_edge_mode &= ~mask;
|
|
level &= ~mask;
|
|
polarity |= mask;
|
|
break;
|
|
case IRQ_TYPE_LEVEL_LOW:
|
|
bank->toggle_edge_mode &= ~mask;
|
|
level &= ~mask;
|
|
polarity &= ~mask;
|
|
break;
|
|
default:
|
|
irq_gc_unlock(gc);
|
|
raw_spin_unlock_irqrestore(&bank->slock, flags);
|
|
clk_disable(bank->clk);
|
|
return -EINVAL;
|
|
}
|
|
|
|
writel_relaxed(level, gc->reg_base + GPIO_INTTYPE_LEVEL);
|
|
writel_relaxed(polarity, gc->reg_base + GPIO_INT_POLARITY);
|
|
|
|
irq_gc_unlock(gc);
|
|
raw_spin_unlock_irqrestore(&bank->slock, flags);
|
|
clk_disable(bank->clk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void rockchip_irq_suspend(struct irq_data *d)
|
|
{
|
|
struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
|
|
struct rockchip_pin_bank *bank = gc->private;
|
|
|
|
clk_enable(bank->clk);
|
|
bank->saved_masks = irq_reg_readl(gc, GPIO_INTMASK);
|
|
irq_reg_writel(gc, ~gc->wake_active, GPIO_INTMASK);
|
|
clk_disable(bank->clk);
|
|
}
|
|
|
|
static void rockchip_irq_resume(struct irq_data *d)
|
|
{
|
|
struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
|
|
struct rockchip_pin_bank *bank = gc->private;
|
|
|
|
clk_enable(bank->clk);
|
|
irq_reg_writel(gc, bank->saved_masks, GPIO_INTMASK);
|
|
clk_disable(bank->clk);
|
|
}
|
|
|
|
static void rockchip_irq_enable(struct irq_data *d)
|
|
{
|
|
struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
|
|
struct rockchip_pin_bank *bank = gc->private;
|
|
|
|
clk_enable(bank->clk);
|
|
irq_gc_mask_clr_bit(d);
|
|
}
|
|
|
|
static void rockchip_irq_disable(struct irq_data *d)
|
|
{
|
|
struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
|
|
struct rockchip_pin_bank *bank = gc->private;
|
|
|
|
irq_gc_mask_set_bit(d);
|
|
clk_disable(bank->clk);
|
|
}
|
|
|
|
static int rockchip_interrupts_register(struct platform_device *pdev,
|
|
struct rockchip_pinctrl *info)
|
|
{
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct rockchip_pin_bank *bank = ctrl->pin_banks;
|
|
unsigned int clr = IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_NOAUTOEN;
|
|
struct irq_chip_generic *gc;
|
|
int ret;
|
|
int i, j;
|
|
|
|
for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
|
|
if (!bank->valid) {
|
|
dev_warn(&pdev->dev, "bank %s is not valid\n",
|
|
bank->name);
|
|
continue;
|
|
}
|
|
|
|
ret = clk_enable(bank->clk);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to enable clock for bank %s\n",
|
|
bank->name);
|
|
continue;
|
|
}
|
|
|
|
bank->domain = irq_domain_add_linear(bank->of_node, 32,
|
|
&irq_generic_chip_ops, NULL);
|
|
if (!bank->domain) {
|
|
dev_warn(&pdev->dev, "could not initialize irq domain for bank %s\n",
|
|
bank->name);
|
|
clk_disable(bank->clk);
|
|
continue;
|
|
}
|
|
|
|
ret = irq_alloc_domain_generic_chips(bank->domain, 32, 1,
|
|
"rockchip_gpio_irq", handle_level_irq,
|
|
clr, 0, IRQ_GC_INIT_MASK_CACHE);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "could not alloc generic chips for bank %s\n",
|
|
bank->name);
|
|
irq_domain_remove(bank->domain);
|
|
clk_disable(bank->clk);
|
|
continue;
|
|
}
|
|
|
|
/*
|
|
* Linux assumes that all interrupts start out disabled/masked.
|
|
* Our driver only uses the concept of masked and always keeps
|
|
* things enabled, so for us that's all masked and all enabled.
|
|
*/
|
|
writel_relaxed(0xffffffff, bank->reg_base + GPIO_INTMASK);
|
|
writel_relaxed(0xffffffff, bank->reg_base + GPIO_INTEN);
|
|
|
|
gc = irq_get_domain_generic_chip(bank->domain, 0);
|
|
gc->reg_base = bank->reg_base;
|
|
gc->private = bank;
|
|
gc->chip_types[0].regs.mask = GPIO_INTMASK;
|
|
gc->chip_types[0].regs.ack = GPIO_PORTS_EOI;
|
|
gc->chip_types[0].chip.irq_ack = irq_gc_ack_set_bit;
|
|
gc->chip_types[0].chip.irq_mask = irq_gc_mask_set_bit;
|
|
gc->chip_types[0].chip.irq_unmask = irq_gc_mask_clr_bit;
|
|
gc->chip_types[0].chip.irq_enable = rockchip_irq_enable;
|
|
gc->chip_types[0].chip.irq_disable = rockchip_irq_disable;
|
|
gc->chip_types[0].chip.irq_set_wake = irq_gc_set_wake;
|
|
gc->chip_types[0].chip.irq_suspend = rockchip_irq_suspend;
|
|
gc->chip_types[0].chip.irq_resume = rockchip_irq_resume;
|
|
gc->chip_types[0].chip.irq_set_type = rockchip_irq_set_type;
|
|
gc->wake_enabled = IRQ_MSK(bank->nr_pins);
|
|
|
|
irq_set_chained_handler_and_data(bank->irq,
|
|
rockchip_irq_demux, bank);
|
|
|
|
/* map the gpio irqs here, when the clock is still running */
|
|
for (j = 0 ; j < 32 ; j++)
|
|
irq_create_mapping(bank->domain, j);
|
|
|
|
clk_disable(bank->clk);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_gpiolib_register(struct platform_device *pdev,
|
|
struct rockchip_pinctrl *info)
|
|
{
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct rockchip_pin_bank *bank = ctrl->pin_banks;
|
|
struct gpio_chip *gc;
|
|
int ret;
|
|
int i;
|
|
|
|
for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
|
|
if (!bank->valid) {
|
|
dev_warn(&pdev->dev, "bank %s is not valid\n",
|
|
bank->name);
|
|
continue;
|
|
}
|
|
|
|
bank->gpio_chip = rockchip_gpiolib_chip;
|
|
|
|
gc = &bank->gpio_chip;
|
|
gc->base = bank->pin_base;
|
|
gc->ngpio = bank->nr_pins;
|
|
gc->parent = &pdev->dev;
|
|
gc->of_node = bank->of_node;
|
|
gc->label = bank->name;
|
|
|
|
ret = gpiochip_add_data(gc, bank);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
|
|
gc->label, ret);
|
|
goto fail;
|
|
}
|
|
}
|
|
|
|
rockchip_interrupts_register(pdev, info);
|
|
|
|
return 0;
|
|
|
|
fail:
|
|
for (--i, --bank; i >= 0; --i, --bank) {
|
|
if (!bank->valid)
|
|
continue;
|
|
gpiochip_remove(&bank->gpio_chip);
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
static int rockchip_gpiolib_unregister(struct platform_device *pdev,
|
|
struct rockchip_pinctrl *info)
|
|
{
|
|
struct rockchip_pin_ctrl *ctrl = info->ctrl;
|
|
struct rockchip_pin_bank *bank = ctrl->pin_banks;
|
|
int i;
|
|
|
|
for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
|
|
if (!bank->valid)
|
|
continue;
|
|
gpiochip_remove(&bank->gpio_chip);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_get_bank_data(struct rockchip_pin_bank *bank,
|
|
struct rockchip_pinctrl *info)
|
|
{
|
|
struct resource res;
|
|
void __iomem *base;
|
|
|
|
if (of_address_to_resource(bank->of_node, 0, &res)) {
|
|
dev_err(info->dev, "cannot find IO resource for bank\n");
|
|
return -ENOENT;
|
|
}
|
|
|
|
bank->reg_base = devm_ioremap_resource(info->dev, &res);
|
|
if (IS_ERR(bank->reg_base))
|
|
return PTR_ERR(bank->reg_base);
|
|
|
|
/*
|
|
* special case, where parts of the pull setting-registers are
|
|
* part of the PMU register space
|
|
*/
|
|
if (of_device_is_compatible(bank->of_node,
|
|
"rockchip,rk3188-gpio-bank0")) {
|
|
struct device_node *node;
|
|
|
|
node = of_parse_phandle(bank->of_node->parent,
|
|
"rockchip,pmu", 0);
|
|
if (!node) {
|
|
if (of_address_to_resource(bank->of_node, 1, &res)) {
|
|
dev_err(info->dev, "cannot find IO resource for bank\n");
|
|
return -ENOENT;
|
|
}
|
|
|
|
base = devm_ioremap_resource(info->dev, &res);
|
|
if (IS_ERR(base))
|
|
return PTR_ERR(base);
|
|
rockchip_regmap_config.max_register =
|
|
resource_size(&res) - 4;
|
|
rockchip_regmap_config.name =
|
|
"rockchip,rk3188-gpio-bank0-pull";
|
|
bank->regmap_pull = devm_regmap_init_mmio(info->dev,
|
|
base,
|
|
&rockchip_regmap_config);
|
|
}
|
|
of_node_put(node);
|
|
}
|
|
|
|
bank->irq = irq_of_parse_and_map(bank->of_node, 0);
|
|
|
|
bank->clk = of_clk_get(bank->of_node, 0);
|
|
if (IS_ERR(bank->clk))
|
|
return PTR_ERR(bank->clk);
|
|
|
|
return clk_prepare(bank->clk);
|
|
}
|
|
|
|
static const struct of_device_id rockchip_pinctrl_dt_match[];
|
|
|
|
/* retrieve the soc specific data */
|
|
static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(
|
|
struct rockchip_pinctrl *d,
|
|
struct platform_device *pdev)
|
|
{
|
|
const struct of_device_id *match;
|
|
struct device_node *node = pdev->dev.of_node;
|
|
struct device_node *np;
|
|
struct rockchip_pin_ctrl *ctrl;
|
|
struct rockchip_pin_bank *bank;
|
|
int grf_offs, pmu_offs, drv_grf_offs, drv_pmu_offs, i, j;
|
|
|
|
match = of_match_node(rockchip_pinctrl_dt_match, node);
|
|
ctrl = (struct rockchip_pin_ctrl *)match->data;
|
|
|
|
for_each_child_of_node(node, np) {
|
|
if (!of_find_property(np, "gpio-controller", NULL))
|
|
continue;
|
|
|
|
bank = ctrl->pin_banks;
|
|
for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
|
|
if (!strcmp(bank->name, np->name)) {
|
|
bank->of_node = np;
|
|
|
|
if (!rockchip_get_bank_data(bank, d))
|
|
bank->valid = true;
|
|
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
grf_offs = ctrl->grf_mux_offset;
|
|
pmu_offs = ctrl->pmu_mux_offset;
|
|
drv_pmu_offs = ctrl->pmu_drv_offset;
|
|
drv_grf_offs = ctrl->grf_drv_offset;
|
|
bank = ctrl->pin_banks;
|
|
for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
|
|
int bank_pins = 0;
|
|
|
|
raw_spin_lock_init(&bank->slock);
|
|
bank->drvdata = d;
|
|
bank->pin_base = ctrl->nr_pins;
|
|
ctrl->nr_pins += bank->nr_pins;
|
|
|
|
/* calculate iomux and drv offsets */
|
|
for (j = 0; j < 4; j++) {
|
|
struct rockchip_iomux *iom = &bank->iomux[j];
|
|
struct rockchip_drv *drv = &bank->drv[j];
|
|
int inc;
|
|
|
|
if (bank_pins >= bank->nr_pins)
|
|
break;
|
|
|
|
/* preset iomux offset value, set new start value */
|
|
if (iom->offset >= 0) {
|
|
if (iom->type & IOMUX_SOURCE_PMU)
|
|
pmu_offs = iom->offset;
|
|
else
|
|
grf_offs = iom->offset;
|
|
} else { /* set current iomux offset */
|
|
iom->offset = (iom->type & IOMUX_SOURCE_PMU) ?
|
|
pmu_offs : grf_offs;
|
|
}
|
|
|
|
/* preset drv offset value, set new start value */
|
|
if (drv->offset >= 0) {
|
|
if (iom->type & IOMUX_SOURCE_PMU)
|
|
drv_pmu_offs = drv->offset;
|
|
else
|
|
drv_grf_offs = drv->offset;
|
|
} else { /* set current drv offset */
|
|
drv->offset = (iom->type & IOMUX_SOURCE_PMU) ?
|
|
drv_pmu_offs : drv_grf_offs;
|
|
}
|
|
|
|
dev_dbg(d->dev, "bank %d, iomux %d has iom_offset 0x%x drv_offset 0x%x\n",
|
|
i, j, iom->offset, drv->offset);
|
|
|
|
/*
|
|
* Increase offset according to iomux width.
|
|
* 4bit iomux'es are spread over two registers.
|
|
*/
|
|
inc = (iom->type & (IOMUX_WIDTH_4BIT |
|
|
IOMUX_WIDTH_3BIT)) ? 8 : 4;
|
|
if (iom->type & IOMUX_SOURCE_PMU)
|
|
pmu_offs += inc;
|
|
else
|
|
grf_offs += inc;
|
|
|
|
/*
|
|
* Increase offset according to drv width.
|
|
* 3bit drive-strenth'es are spread over two registers.
|
|
*/
|
|
if ((drv->drv_type == DRV_TYPE_IO_1V8_3V0_AUTO) ||
|
|
(drv->drv_type == DRV_TYPE_IO_3V3_ONLY))
|
|
inc = 8;
|
|
else
|
|
inc = 4;
|
|
|
|
if (iom->type & IOMUX_SOURCE_PMU)
|
|
drv_pmu_offs += inc;
|
|
else
|
|
drv_grf_offs += inc;
|
|
|
|
bank_pins += 8;
|
|
}
|
|
|
|
/* calculate the per-bank recalced_mask */
|
|
for (j = 0; j < ctrl->niomux_recalced; j++) {
|
|
int pin = 0;
|
|
|
|
if (ctrl->iomux_recalced[j].num == bank->bank_num) {
|
|
pin = ctrl->iomux_recalced[j].pin;
|
|
bank->recalced_mask |= BIT(pin);
|
|
}
|
|
}
|
|
|
|
/* calculate the per-bank route_mask */
|
|
for (j = 0; j < ctrl->niomux_routes; j++) {
|
|
int pin = 0;
|
|
|
|
if (ctrl->iomux_routes[j].bank_num == bank->bank_num) {
|
|
pin = ctrl->iomux_routes[j].pin;
|
|
bank->route_mask |= BIT(pin);
|
|
}
|
|
}
|
|
}
|
|
|
|
return ctrl;
|
|
}
|
|
|
|
#define RK3288_GRF_GPIO6C_IOMUX 0x64
|
|
#define GPIO6C6_SEL_WRITE_ENABLE BIT(28)
|
|
|
|
static u32 rk3288_grf_gpio6c_iomux;
|
|
|
|
static int __maybe_unused rockchip_pinctrl_suspend(struct device *dev)
|
|
{
|
|
struct rockchip_pinctrl *info = dev_get_drvdata(dev);
|
|
int ret = pinctrl_force_sleep(info->pctl_dev);
|
|
|
|
if (ret)
|
|
return ret;
|
|
|
|
/*
|
|
* RK3288 GPIO6_C6 mux would be modified by Maskrom when resume, so save
|
|
* the setting here, and restore it at resume.
|
|
*/
|
|
if (info->ctrl->type == RK3288) {
|
|
ret = regmap_read(info->regmap_base, RK3288_GRF_GPIO6C_IOMUX,
|
|
&rk3288_grf_gpio6c_iomux);
|
|
if (ret) {
|
|
pinctrl_force_default(info->pctl_dev);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __maybe_unused rockchip_pinctrl_resume(struct device *dev)
|
|
{
|
|
struct rockchip_pinctrl *info = dev_get_drvdata(dev);
|
|
int ret = regmap_write(info->regmap_base, RK3288_GRF_GPIO6C_IOMUX,
|
|
rk3288_grf_gpio6c_iomux |
|
|
GPIO6C6_SEL_WRITE_ENABLE);
|
|
|
|
if (ret)
|
|
return ret;
|
|
|
|
return pinctrl_force_default(info->pctl_dev);
|
|
}
|
|
|
|
static SIMPLE_DEV_PM_OPS(rockchip_pinctrl_dev_pm_ops, rockchip_pinctrl_suspend,
|
|
rockchip_pinctrl_resume);
|
|
|
|
static int rockchip_pinctrl_probe(struct platform_device *pdev)
|
|
{
|
|
struct rockchip_pinctrl *info;
|
|
struct device *dev = &pdev->dev;
|
|
struct rockchip_pin_ctrl *ctrl;
|
|
struct device_node *np = pdev->dev.of_node, *node;
|
|
struct resource *res;
|
|
void __iomem *base;
|
|
int ret;
|
|
|
|
if (!dev->of_node) {
|
|
dev_err(dev, "device tree node not found\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
|
|
if (!info)
|
|
return -ENOMEM;
|
|
|
|
info->dev = dev;
|
|
|
|
ctrl = rockchip_pinctrl_get_soc_data(info, pdev);
|
|
if (!ctrl) {
|
|
dev_err(dev, "driver data not available\n");
|
|
return -EINVAL;
|
|
}
|
|
info->ctrl = ctrl;
|
|
|
|
node = of_parse_phandle(np, "rockchip,grf", 0);
|
|
if (node) {
|
|
info->regmap_base = syscon_node_to_regmap(node);
|
|
if (IS_ERR(info->regmap_base))
|
|
return PTR_ERR(info->regmap_base);
|
|
} else {
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
base = devm_ioremap_resource(&pdev->dev, res);
|
|
if (IS_ERR(base))
|
|
return PTR_ERR(base);
|
|
|
|
rockchip_regmap_config.max_register = resource_size(res) - 4;
|
|
rockchip_regmap_config.name = "rockchip,pinctrl";
|
|
info->regmap_base = devm_regmap_init_mmio(&pdev->dev, base,
|
|
&rockchip_regmap_config);
|
|
|
|
/* to check for the old dt-bindings */
|
|
info->reg_size = resource_size(res);
|
|
|
|
/* Honor the old binding, with pull registers as 2nd resource */
|
|
if (ctrl->type == RK3188 && info->reg_size < 0x200) {
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
|
|
base = devm_ioremap_resource(&pdev->dev, res);
|
|
if (IS_ERR(base))
|
|
return PTR_ERR(base);
|
|
|
|
rockchip_regmap_config.max_register =
|
|
resource_size(res) - 4;
|
|
rockchip_regmap_config.name = "rockchip,pinctrl-pull";
|
|
info->regmap_pull = devm_regmap_init_mmio(&pdev->dev,
|
|
base,
|
|
&rockchip_regmap_config);
|
|
}
|
|
}
|
|
|
|
/* try to find the optional reference to the pmu syscon */
|
|
node = of_parse_phandle(np, "rockchip,pmu", 0);
|
|
if (node) {
|
|
info->regmap_pmu = syscon_node_to_regmap(node);
|
|
if (IS_ERR(info->regmap_pmu))
|
|
return PTR_ERR(info->regmap_pmu);
|
|
}
|
|
|
|
ret = rockchip_gpiolib_register(pdev, info);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = rockchip_pinctrl_register(pdev, info);
|
|
if (ret) {
|
|
rockchip_gpiolib_unregister(pdev, info);
|
|
return ret;
|
|
}
|
|
|
|
platform_set_drvdata(pdev, info);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct rockchip_pin_bank px30_pin_banks[] = {
|
|
PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU
|
|
),
|
|
PIN_BANK_IOMUX_FLAGS(1, 32, "gpio1", IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT
|
|
),
|
|
PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2", IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT
|
|
),
|
|
PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3", IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT
|
|
),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl px30_pin_ctrl = {
|
|
.pin_banks = px30_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(px30_pin_banks),
|
|
.label = "PX30-GPIO",
|
|
.type = PX30,
|
|
.grf_mux_offset = 0x0,
|
|
.pmu_mux_offset = 0x0,
|
|
.iomux_routes = px30_mux_route_data,
|
|
.niomux_routes = ARRAY_SIZE(px30_mux_route_data),
|
|
.pull_calc_reg = px30_calc_pull_reg_and_bit,
|
|
.drv_calc_reg = px30_calc_drv_reg_and_bit,
|
|
.schmitt_calc_reg = px30_calc_schmitt_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rv1108_pin_banks[] = {
|
|
PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU),
|
|
PIN_BANK_IOMUX_FLAGS(1, 32, "gpio1", 0, 0, 0, 0),
|
|
PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2", 0, 0, 0, 0),
|
|
PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3", 0, 0, 0, 0),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rv1108_pin_ctrl = {
|
|
.pin_banks = rv1108_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rv1108_pin_banks),
|
|
.label = "RV1108-GPIO",
|
|
.type = RV1108,
|
|
.grf_mux_offset = 0x10,
|
|
.pmu_mux_offset = 0x0,
|
|
.iomux_recalced = rv1108_mux_recalced_data,
|
|
.niomux_recalced = ARRAY_SIZE(rv1108_mux_recalced_data),
|
|
.pull_calc_reg = rv1108_calc_pull_reg_and_bit,
|
|
.drv_calc_reg = rv1108_calc_drv_reg_and_bit,
|
|
.schmitt_calc_reg = rv1108_calc_schmitt_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk2928_pin_banks[] = {
|
|
PIN_BANK(0, 32, "gpio0"),
|
|
PIN_BANK(1, 32, "gpio1"),
|
|
PIN_BANK(2, 32, "gpio2"),
|
|
PIN_BANK(3, 32, "gpio3"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk2928_pin_ctrl = {
|
|
.pin_banks = rk2928_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk2928_pin_banks),
|
|
.label = "RK2928-GPIO",
|
|
.type = RK2928,
|
|
.grf_mux_offset = 0xa8,
|
|
.pull_calc_reg = rk2928_calc_pull_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3036_pin_banks[] = {
|
|
PIN_BANK(0, 32, "gpio0"),
|
|
PIN_BANK(1, 32, "gpio1"),
|
|
PIN_BANK(2, 32, "gpio2"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3036_pin_ctrl = {
|
|
.pin_banks = rk3036_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3036_pin_banks),
|
|
.label = "RK3036-GPIO",
|
|
.type = RK2928,
|
|
.grf_mux_offset = 0xa8,
|
|
.pull_calc_reg = rk2928_calc_pull_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3066a_pin_banks[] = {
|
|
PIN_BANK(0, 32, "gpio0"),
|
|
PIN_BANK(1, 32, "gpio1"),
|
|
PIN_BANK(2, 32, "gpio2"),
|
|
PIN_BANK(3, 32, "gpio3"),
|
|
PIN_BANK(4, 32, "gpio4"),
|
|
PIN_BANK(6, 16, "gpio6"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3066a_pin_ctrl = {
|
|
.pin_banks = rk3066a_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3066a_pin_banks),
|
|
.label = "RK3066a-GPIO",
|
|
.type = RK2928,
|
|
.grf_mux_offset = 0xa8,
|
|
.pull_calc_reg = rk2928_calc_pull_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3066b_pin_banks[] = {
|
|
PIN_BANK(0, 32, "gpio0"),
|
|
PIN_BANK(1, 32, "gpio1"),
|
|
PIN_BANK(2, 32, "gpio2"),
|
|
PIN_BANK(3, 32, "gpio3"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3066b_pin_ctrl = {
|
|
.pin_banks = rk3066b_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3066b_pin_banks),
|
|
.label = "RK3066b-GPIO",
|
|
.type = RK3066B,
|
|
.grf_mux_offset = 0x60,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3128_pin_banks[] = {
|
|
PIN_BANK(0, 32, "gpio0"),
|
|
PIN_BANK(1, 32, "gpio1"),
|
|
PIN_BANK(2, 32, "gpio2"),
|
|
PIN_BANK(3, 32, "gpio3"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3128_pin_ctrl = {
|
|
.pin_banks = rk3128_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3128_pin_banks),
|
|
.label = "RK3128-GPIO",
|
|
.type = RK3128,
|
|
.grf_mux_offset = 0xa8,
|
|
.iomux_recalced = rk3128_mux_recalced_data,
|
|
.niomux_recalced = ARRAY_SIZE(rk3128_mux_recalced_data),
|
|
.iomux_routes = rk3128_mux_route_data,
|
|
.niomux_routes = ARRAY_SIZE(rk3128_mux_route_data),
|
|
.pull_calc_reg = rk3128_calc_pull_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3188_pin_banks[] = {
|
|
PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", IOMUX_GPIO_ONLY, 0, 0, 0),
|
|
PIN_BANK(1, 32, "gpio1"),
|
|
PIN_BANK(2, 32, "gpio2"),
|
|
PIN_BANK(3, 32, "gpio3"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3188_pin_ctrl = {
|
|
.pin_banks = rk3188_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3188_pin_banks),
|
|
.label = "RK3188-GPIO",
|
|
.type = RK3188,
|
|
.grf_mux_offset = 0x60,
|
|
.iomux_routes = rk3188_mux_route_data,
|
|
.niomux_routes = ARRAY_SIZE(rk3188_mux_route_data),
|
|
.pull_calc_reg = rk3188_calc_pull_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3228_pin_banks[] = {
|
|
PIN_BANK(0, 32, "gpio0"),
|
|
PIN_BANK(1, 32, "gpio1"),
|
|
PIN_BANK(2, 32, "gpio2"),
|
|
PIN_BANK(3, 32, "gpio3"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3228_pin_ctrl = {
|
|
.pin_banks = rk3228_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3228_pin_banks),
|
|
.label = "RK3228-GPIO",
|
|
.type = RK3288,
|
|
.grf_mux_offset = 0x0,
|
|
.iomux_routes = rk3228_mux_route_data,
|
|
.niomux_routes = ARRAY_SIZE(rk3228_mux_route_data),
|
|
.pull_calc_reg = rk3228_calc_pull_reg_and_bit,
|
|
.drv_calc_reg = rk3228_calc_drv_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3288_pin_banks[] = {
|
|
PIN_BANK_IOMUX_FLAGS(0, 24, "gpio0", IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_UNROUTED
|
|
),
|
|
PIN_BANK_IOMUX_FLAGS(1, 32, "gpio1", IOMUX_UNROUTED,
|
|
IOMUX_UNROUTED,
|
|
IOMUX_UNROUTED,
|
|
0
|
|
),
|
|
PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2", 0, 0, 0, IOMUX_UNROUTED),
|
|
PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3", 0, 0, 0, IOMUX_WIDTH_4BIT),
|
|
PIN_BANK_IOMUX_FLAGS(4, 32, "gpio4", IOMUX_WIDTH_4BIT,
|
|
IOMUX_WIDTH_4BIT,
|
|
0,
|
|
0
|
|
),
|
|
PIN_BANK_IOMUX_FLAGS(5, 32, "gpio5", IOMUX_UNROUTED,
|
|
0,
|
|
0,
|
|
IOMUX_UNROUTED
|
|
),
|
|
PIN_BANK_IOMUX_FLAGS(6, 32, "gpio6", 0, 0, 0, IOMUX_UNROUTED),
|
|
PIN_BANK_IOMUX_FLAGS(7, 32, "gpio7", 0,
|
|
0,
|
|
IOMUX_WIDTH_4BIT,
|
|
IOMUX_UNROUTED
|
|
),
|
|
PIN_BANK(8, 16, "gpio8"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3288_pin_ctrl = {
|
|
.pin_banks = rk3288_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3288_pin_banks),
|
|
.label = "RK3288-GPIO",
|
|
.type = RK3288,
|
|
.grf_mux_offset = 0x0,
|
|
.pmu_mux_offset = 0x84,
|
|
.iomux_routes = rk3288_mux_route_data,
|
|
.niomux_routes = ARRAY_SIZE(rk3288_mux_route_data),
|
|
.pull_calc_reg = rk3288_calc_pull_reg_and_bit,
|
|
.drv_calc_reg = rk3288_calc_drv_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3328_pin_banks[] = {
|
|
PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", 0, 0, 0, 0),
|
|
PIN_BANK_IOMUX_FLAGS(1, 32, "gpio1", 0, 0, 0, 0),
|
|
PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2", 0,
|
|
IOMUX_WIDTH_3BIT,
|
|
IOMUX_WIDTH_3BIT,
|
|
0),
|
|
PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3",
|
|
IOMUX_WIDTH_3BIT,
|
|
IOMUX_WIDTH_3BIT,
|
|
0,
|
|
0),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3328_pin_ctrl = {
|
|
.pin_banks = rk3328_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3328_pin_banks),
|
|
.label = "RK3328-GPIO",
|
|
.type = RK3288,
|
|
.grf_mux_offset = 0x0,
|
|
.iomux_recalced = rk3328_mux_recalced_data,
|
|
.niomux_recalced = ARRAY_SIZE(rk3328_mux_recalced_data),
|
|
.iomux_routes = rk3328_mux_route_data,
|
|
.niomux_routes = ARRAY_SIZE(rk3328_mux_route_data),
|
|
.pull_calc_reg = rk3228_calc_pull_reg_and_bit,
|
|
.drv_calc_reg = rk3228_calc_drv_reg_and_bit,
|
|
.schmitt_calc_reg = rk3328_calc_schmitt_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3368_pin_banks[] = {
|
|
PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU
|
|
),
|
|
PIN_BANK(1, 32, "gpio1"),
|
|
PIN_BANK(2, 32, "gpio2"),
|
|
PIN_BANK(3, 32, "gpio3"),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3368_pin_ctrl = {
|
|
.pin_banks = rk3368_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3368_pin_banks),
|
|
.label = "RK3368-GPIO",
|
|
.type = RK3368,
|
|
.grf_mux_offset = 0x0,
|
|
.pmu_mux_offset = 0x0,
|
|
.pull_calc_reg = rk3368_calc_pull_reg_and_bit,
|
|
.drv_calc_reg = rk3368_calc_drv_reg_and_bit,
|
|
};
|
|
|
|
static struct rockchip_pin_bank rk3399_pin_banks[] = {
|
|
PIN_BANK_IOMUX_FLAGS_DRV_FLAGS_OFFSET_PULL_FLAGS(0, 32, "gpio0",
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
DRV_TYPE_IO_1V8_ONLY,
|
|
DRV_TYPE_IO_1V8_ONLY,
|
|
DRV_TYPE_IO_DEFAULT,
|
|
DRV_TYPE_IO_DEFAULT,
|
|
0x80,
|
|
0x88,
|
|
-1,
|
|
-1,
|
|
PULL_TYPE_IO_1V8_ONLY,
|
|
PULL_TYPE_IO_1V8_ONLY,
|
|
PULL_TYPE_IO_DEFAULT,
|
|
PULL_TYPE_IO_DEFAULT
|
|
),
|
|
PIN_BANK_IOMUX_DRV_FLAGS_OFFSET(1, 32, "gpio1", IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
IOMUX_SOURCE_PMU,
|
|
DRV_TYPE_IO_1V8_OR_3V0,
|
|
DRV_TYPE_IO_1V8_OR_3V0,
|
|
DRV_TYPE_IO_1V8_OR_3V0,
|
|
DRV_TYPE_IO_1V8_OR_3V0,
|
|
0xa0,
|
|
0xa8,
|
|
0xb0,
|
|
0xb8
|
|
),
|
|
PIN_BANK_DRV_FLAGS_PULL_FLAGS(2, 32, "gpio2", DRV_TYPE_IO_1V8_OR_3V0,
|
|
DRV_TYPE_IO_1V8_OR_3V0,
|
|
DRV_TYPE_IO_1V8_ONLY,
|
|
DRV_TYPE_IO_1V8_ONLY,
|
|
PULL_TYPE_IO_DEFAULT,
|
|
PULL_TYPE_IO_DEFAULT,
|
|
PULL_TYPE_IO_1V8_ONLY,
|
|
PULL_TYPE_IO_1V8_ONLY
|
|
),
|
|
PIN_BANK_DRV_FLAGS(3, 32, "gpio3", DRV_TYPE_IO_3V3_ONLY,
|
|
DRV_TYPE_IO_3V3_ONLY,
|
|
DRV_TYPE_IO_3V3_ONLY,
|
|
DRV_TYPE_IO_1V8_OR_3V0
|
|
),
|
|
PIN_BANK_DRV_FLAGS(4, 32, "gpio4", DRV_TYPE_IO_1V8_OR_3V0,
|
|
DRV_TYPE_IO_1V8_3V0_AUTO,
|
|
DRV_TYPE_IO_1V8_OR_3V0,
|
|
DRV_TYPE_IO_1V8_OR_3V0
|
|
),
|
|
};
|
|
|
|
static struct rockchip_pin_ctrl rk3399_pin_ctrl = {
|
|
.pin_banks = rk3399_pin_banks,
|
|
.nr_banks = ARRAY_SIZE(rk3399_pin_banks),
|
|
.label = "RK3399-GPIO",
|
|
.type = RK3399,
|
|
.grf_mux_offset = 0xe000,
|
|
.pmu_mux_offset = 0x0,
|
|
.grf_drv_offset = 0xe100,
|
|
.pmu_drv_offset = 0x80,
|
|
.iomux_routes = rk3399_mux_route_data,
|
|
.niomux_routes = ARRAY_SIZE(rk3399_mux_route_data),
|
|
.pull_calc_reg = rk3399_calc_pull_reg_and_bit,
|
|
.drv_calc_reg = rk3399_calc_drv_reg_and_bit,
|
|
};
|
|
|
|
static const struct of_device_id rockchip_pinctrl_dt_match[] = {
|
|
{ .compatible = "rockchip,px30-pinctrl",
|
|
.data = &px30_pin_ctrl },
|
|
{ .compatible = "rockchip,rv1108-pinctrl",
|
|
.data = &rv1108_pin_ctrl },
|
|
{ .compatible = "rockchip,rk2928-pinctrl",
|
|
.data = &rk2928_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3036-pinctrl",
|
|
.data = &rk3036_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3066a-pinctrl",
|
|
.data = &rk3066a_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3066b-pinctrl",
|
|
.data = &rk3066b_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3128-pinctrl",
|
|
.data = (void *)&rk3128_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3188-pinctrl",
|
|
.data = &rk3188_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3228-pinctrl",
|
|
.data = &rk3228_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3288-pinctrl",
|
|
.data = &rk3288_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3328-pinctrl",
|
|
.data = &rk3328_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3368-pinctrl",
|
|
.data = &rk3368_pin_ctrl },
|
|
{ .compatible = "rockchip,rk3399-pinctrl",
|
|
.data = &rk3399_pin_ctrl },
|
|
{},
|
|
};
|
|
|
|
static struct platform_driver rockchip_pinctrl_driver = {
|
|
.probe = rockchip_pinctrl_probe,
|
|
.driver = {
|
|
.name = "rockchip-pinctrl",
|
|
.pm = &rockchip_pinctrl_dev_pm_ops,
|
|
.of_match_table = rockchip_pinctrl_dt_match,
|
|
},
|
|
};
|
|
|
|
static int __init rockchip_pinctrl_drv_register(void)
|
|
{
|
|
return platform_driver_register(&rockchip_pinctrl_driver);
|
|
}
|
|
postcore_initcall(rockchip_pinctrl_drv_register);
|