mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
43167bb1f6
Mixing array constraints like 'maxItems' and string or integer value constraints like 'minimum' don't make sense. Also, with only value constraints, it is implied we have a single value. So lets remove 'maxItems: 1'. Cc: Mark Brown <broonie@kernel.org> Cc: linux-spi@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20190709192631.16394-1-robh@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
161 lines
4.0 KiB
YAML
161 lines
4.0 KiB
YAML
# SPDX-License-Identifier: GPL-2.0
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/spi/spi-controller.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: SPI Controller Generic Binding
|
|
|
|
maintainers:
|
|
- Mark Brown <broonie@kernel.org>
|
|
|
|
description: |
|
|
SPI busses can be described with a node for the SPI controller device
|
|
and a set of child nodes for each SPI slave on the bus. The system SPI
|
|
controller may be described for use in SPI master mode or in SPI slave mode,
|
|
but not for both at the same time.
|
|
|
|
properties:
|
|
$nodename:
|
|
pattern: "^spi(@.*|-[0-9a-f])*$"
|
|
|
|
"#address-cells":
|
|
const: 1
|
|
|
|
"#size-cells":
|
|
const: 0
|
|
|
|
cs-gpios:
|
|
description: |
|
|
GPIOs used as chip selects.
|
|
If that property is used, the number of chip selects will be
|
|
increased automatically with max(cs-gpios, hardware chip selects).
|
|
|
|
So if, for example, the controller has 2 CS lines, and the
|
|
cs-gpios looks like this
|
|
cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>;
|
|
|
|
Then it should be configured so that num_chipselect = 4, with
|
|
the following mapping
|
|
cs0 : &gpio1 0 0
|
|
cs1 : native
|
|
cs2 : &gpio1 1 0
|
|
cs3 : &gpio1 2 0
|
|
|
|
num-cs:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description:
|
|
Total number of chip selects.
|
|
|
|
spi-slave:
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
description:
|
|
The SPI controller acts as a slave, instead of a master.
|
|
|
|
patternProperties:
|
|
"^slave$":
|
|
type: object
|
|
|
|
properties:
|
|
compatible:
|
|
description:
|
|
Compatible of the SPI device.
|
|
|
|
required:
|
|
- compatible
|
|
|
|
"^.*@[0-9a-f]+$":
|
|
type: object
|
|
|
|
properties:
|
|
compatible:
|
|
description:
|
|
Compatible of the SPI device.
|
|
|
|
reg:
|
|
minimum: 0
|
|
maximum: 256
|
|
description:
|
|
Chip select used by the device.
|
|
|
|
spi-3wire:
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
description:
|
|
The device requires 3-wire mode.
|
|
|
|
spi-cpha:
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
description:
|
|
The device requires shifted clock phase (CPHA) mode.
|
|
|
|
spi-cpol:
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
description:
|
|
The device requires inverse clock polarity (CPOL) mode.
|
|
|
|
spi-cs-high:
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
description:
|
|
The device requires the chip select active high.
|
|
|
|
spi-lsb-first:
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
description:
|
|
The device requires the LSB first mode.
|
|
|
|
spi-max-frequency:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description:
|
|
Maximum SPI clocking speed of the device in Hz.
|
|
|
|
spi-rx-bus-width:
|
|
allOf:
|
|
- $ref: /schemas/types.yaml#/definitions/uint32
|
|
- enum: [ 1, 2, 4 ]
|
|
- default: 1
|
|
description:
|
|
Bus width to the SPI bus used for MISO.
|
|
|
|
spi-rx-delay-us:
|
|
description:
|
|
Delay, in microseconds, after a read transfer.
|
|
|
|
spi-tx-bus-width:
|
|
allOf:
|
|
- $ref: /schemas/types.yaml#/definitions/uint32
|
|
- enum: [ 1, 2, 4 ]
|
|
- default: 1
|
|
description:
|
|
Bus width to the SPI bus used for MOSI.
|
|
|
|
spi-tx-delay-us:
|
|
description:
|
|
Delay, in microseconds, after a write transfer.
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
|
|
examples:
|
|
- |
|
|
spi@f00 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
|
|
reg = <0xf00 0x20>;
|
|
interrupts = <2 13 0 2 14 0>;
|
|
interrupt-parent = <&mpc5200_pic>;
|
|
|
|
ethernet-switch@0 {
|
|
compatible = "micrel,ks8995m";
|
|
spi-max-frequency = <1000000>;
|
|
reg = <0>;
|
|
};
|
|
|
|
codec@1 {
|
|
compatible = "ti,tlv320aic26";
|
|
spi-max-frequency = <100000>;
|
|
reg = <1>;
|
|
};
|
|
};
|