mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-02 23:56:42 +07:00
7d71d5b2e8
the setup before the change was - arch/powerpc/Kconfig had the PPC_CLOCK option, off by default - depending on the PPC_CLOCK option the arch/powerpc/kernel/clock.c file was built, which implements the clk.h API but always returns -ENOSYS unless a platform registers specific callbacks - the MPC52xx platform selected PPC_CLOCK but did not register any callbacks, thus all clk.h API calls keep resulting in -ENOSYS errors (which is OK, all peripheral drivers deal with the situation) - the MPC512x platform selected PPC_CLOCK and registered specific callbacks implemented in arch/powerpc/platforms/512x/clock.c, thus provided real support for the clock API - no other powerpc platform did select PPC_CLOCK the situation after the change is - the MPC512x platform implements the COMMON_CLK interface, and thus the PPC_CLOCK approach in arch/powerpc/platforms/512x/clock.c has become obsolete - the MPC52xx platform still lacks genuine support for the clk.h API while this is not a change against the previous situation (the error code returned from COMMON_CLK stubs differs but every call still results in an error) - with all references gone, the arch/powerpc/kernel/clock.c wrapper and the PPC_CLOCK option have become obsolete, as did the clk_interface.h header file the switch from PPC_CLOCK to COMMON_CLK is done for all platforms within the same commit such that multiplatform kernels (the combination of 512x and 52xx within one executable) keep working Cc: Mike Turquette <mturquette@linaro.org> Cc: Anatolij Gustschin <agust@denx.de> Cc: linux-arm-kernel@lists.infradead.org Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de>
62 lines
1.7 KiB
Plaintext
62 lines
1.7 KiB
Plaintext
config PPC_MPC52xx
|
|
bool "52xx-based boards"
|
|
depends on 6xx
|
|
select COMMON_CLK
|
|
select PPC_PCI_CHOICE
|
|
|
|
config PPC_MPC5200_SIMPLE
|
|
bool "Generic support for simple MPC5200 based boards"
|
|
depends on PPC_MPC52xx
|
|
select DEFAULT_UIMAGE
|
|
help
|
|
This option enables support for a simple MPC52xx based boards which
|
|
do not need a custom platform specific setup. Such boards are
|
|
supported assuming the following:
|
|
|
|
- GPIO pins are configured by the firmware,
|
|
- CDM configuration (clocking) is setup correctly by firmware,
|
|
- if the 'fsl,has-wdt' property is present in one of the
|
|
gpt nodes, then it is safe to use such gpt to reset the board,
|
|
- PCI is supported if enabled in the kernel configuration
|
|
and if there is a PCI bus node defined in the device tree.
|
|
|
|
Boards that are compatible with this generic platform support
|
|
are:
|
|
intercontrol,digsy-mtc
|
|
phytec,pcm030
|
|
phytec,pcm032
|
|
promess,motionpro
|
|
schindler,cm5200
|
|
tqc,tqm5200
|
|
|
|
config PPC_EFIKA
|
|
bool "bPlan Efika 5k2. MPC5200B based computer"
|
|
depends on PPC_MPC52xx
|
|
select PPC_RTAS
|
|
select RTAS_PROC
|
|
select PPC_NATIVE
|
|
|
|
config PPC_LITE5200
|
|
bool "Freescale Lite5200 Eval Board"
|
|
depends on PPC_MPC52xx
|
|
select DEFAULT_UIMAGE
|
|
|
|
config PPC_MEDIA5200
|
|
bool "Freescale Media5200 Eval Board"
|
|
depends on PPC_MPC52xx
|
|
select DEFAULT_UIMAGE
|
|
|
|
config PPC_MPC5200_BUGFIX
|
|
bool "MPC5200 (L25R) bugfix support"
|
|
depends on PPC_MPC52xx
|
|
help
|
|
Enable workarounds for original MPC5200 errata. This is not required
|
|
for MPC5200B based boards.
|
|
|
|
It is safe to say 'Y' here
|
|
|
|
config PPC_MPC5200_LPBFIFO
|
|
tristate "MPC5200 LocalPlus bus FIFO driver"
|
|
depends on PPC_MPC52xx && PPC_BESTCOMM
|
|
select PPC_BESTCOMM_GEN_BD
|