mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-25 13:40:53 +07:00
54aaa1ca10
This patch removes the fix_hstcfg option from the driver and related SMBus Interrupt Select register magic because now we know what are valid values for this register. This patch updates the documentation and adds new IRQ mode check so we are sure not to miss any new "unusual" value. The PCI quirk for users of fix_hstcfg was not developed because the chipset lacks of subsystem ID registers and DMI is stated "To be filled". Impact to existing systems is minimal because the problem showed up on motherboards like 10 years back. On the other hand users of newer Serverworks and HT1000 systems won't be misleaded by the message suggesting to try the fix_hstcfg any more. Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
85 lines
3.5 KiB
Plaintext
85 lines
3.5 KiB
Plaintext
Kernel driver i2c-piix4
|
|
|
|
Supported adapters:
|
|
* Intel 82371AB PIIX4 and PIIX4E
|
|
* Intel 82443MX (440MX)
|
|
Datasheet: Publicly available at the Intel website
|
|
* ServerWorks OSB4, CSB5, CSB6 and HT-1000 southbridges
|
|
Datasheet: Only available via NDA from ServerWorks
|
|
* ATI IXP southbridges IXP200, IXP300, IXP400
|
|
Datasheet: Not publicly available
|
|
* Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge
|
|
Datasheet: Publicly available at the SMSC website http://www.smsc.com
|
|
|
|
Authors:
|
|
Frodo Looijaard <frodol@dds.nl>
|
|
Philip Edelbrock <phil@netroedge.com>
|
|
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
* force: int
|
|
Forcibly enable the PIIX4. DANGEROUS!
|
|
* force_addr: int
|
|
Forcibly enable the PIIX4 at the given address. EXTREMELY DANGEROUS!
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
The PIIX4 (properly known as the 82371AB) is an Intel chip with a lot of
|
|
functionality. Among other things, it implements the PCI bus. One of its
|
|
minor functions is implementing a System Management Bus. This is a true
|
|
SMBus - you can not access it on I2C levels. The good news is that it
|
|
natively understands SMBus commands and you do not have to worry about
|
|
timing problems. The bad news is that non-SMBus devices connected to it can
|
|
confuse it mightily. Yes, this is known to happen...
|
|
|
|
Do 'lspci -v' and see whether it contains an entry like this:
|
|
|
|
0000:00:02.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
|
|
Flags: medium devsel, IRQ 9
|
|
|
|
Bus and device numbers may differ, but the function number must be
|
|
identical (like many PCI devices, the PIIX4 incorporates a number of
|
|
different 'functions', which can be considered as separate devices). If you
|
|
find such an entry, you have a PIIX4 SMBus controller.
|
|
|
|
On some computers (most notably, some Dells), the SMBus is disabled by
|
|
default. If you use the insmod parameter 'force=1', the kernel module will
|
|
try to enable it. THIS IS VERY DANGEROUS! If the BIOS did not set up a
|
|
correct address for this module, you could get in big trouble (read:
|
|
crashes, data corruption, etc.). Try this only as a last resort (try BIOS
|
|
updates first, for example), and backup first! An even more dangerous
|
|
option is 'force_addr=<IOPORT>'. This will not only enable the PIIX4 like
|
|
'force' foes, but it will also set a new base I/O port address. The SMBus
|
|
parts of the PIIX4 needs a range of 8 of these addresses to function
|
|
correctly. If these addresses are already reserved by some other device,
|
|
you will get into big trouble! DON'T USE THIS IF YOU ARE NOT VERY SURE
|
|
ABOUT WHAT YOU ARE DOING!
|
|
|
|
The PIIX4E is just an new version of the PIIX4; it is supported as well.
|
|
The PIIX/PIIX3 does not implement an SMBus or I2C bus, so you can't use
|
|
this driver on those mainboards.
|
|
|
|
The ServerWorks Southbridges, the Intel 440MX, and the Victory766 are
|
|
identical to the PIIX4 in I2C/SMBus support.
|
|
|
|
If you own Force CPCI735 motherboard or other OSB4 based systems you may need
|
|
to change the SMBus Interrupt Select register so the SMBus controller uses
|
|
the SMI mode.
|
|
|
|
1) Use lspci command and locate the PCI device with the SMBus controller:
|
|
00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 4f)
|
|
The line may vary for different chipsets. Please consult the driver source
|
|
for all possible PCI ids (and lspci -n to match them). Lets assume the
|
|
device is located at 00:0f.0.
|
|
2) Now you just need to change the value in 0xD2 register. Get it first with
|
|
command: lspci -xxx -s 00:0f.0
|
|
If the value is 0x3 then you need to change it to 0x1
|
|
setpci -s 00:0f.0 d2.b=1
|
|
|
|
Please note that you don't need to do that in all cases, just when the SMBus is
|
|
not working properly.
|