mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-18 23:48:53 +07:00
3b79919946
Use the new bindings of the Marvell NAND controller driver. Also adapt the NAND controller node organization to distinguish which property is relevant for the controller, and which one is NAND chip specific. Expose the partitions as a subnode of the NAND chip. Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as the new driver activates the arbiter by default for all boards which is either needed or harmless. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
106 lines
2.2 KiB
Plaintext
106 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Device Tree file for DB-XC3-24G4XG board
|
|
*
|
|
* Copyright (C) 2016 Allied Telesis Labs
|
|
*
|
|
* Based on armada-xp-db.dts
|
|
*
|
|
* Note: this Device Tree assumes that the bootloader has remapped the
|
|
* internal registers to 0xf1000000 (instead of the default
|
|
* 0xd0000000). The 0xf1000000 is the default used by the recent,
|
|
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
|
|
* boards were delivered with an older version of the bootloader that
|
|
* left internal registers mapped at 0xd0000000. If you are in this
|
|
* situation, you should either update your bootloader (preferred
|
|
* solution) or the below Device Tree should be adjusted.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "armada-xp-98dx3336.dtsi"
|
|
|
|
/ {
|
|
model = "DB-XC3-24G4XG";
|
|
compatible = "marvell,db-xc3-24g4xg", "marvell,armadaxp-98dx3336", "marvell,armada-370-xp";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200 earlyprintk";
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0 0x00000000 0 0x40000000>; /* 1 GB */
|
|
};
|
|
};
|
|
|
|
&devbus_bootcs {
|
|
status = "okay";
|
|
|
|
/* Device Bus parameters are required */
|
|
|
|
/* Read parameters */
|
|
devbus,bus-width = <16>;
|
|
devbus,turn-off-ps = <60000>;
|
|
devbus,badr-skew-ps = <0>;
|
|
devbus,acc-first-ps = <124000>;
|
|
devbus,acc-next-ps = <248000>;
|
|
devbus,rd-setup-ps = <0>;
|
|
devbus,rd-hold-ps = <0>;
|
|
|
|
/* Write parameters */
|
|
devbus,sync-enable = <0>;
|
|
devbus,wr-high-ps = <60000>;
|
|
devbus,wr-low-ps = <60000>;
|
|
devbus,ale-wr-ps = <60000>;
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c0 {
|
|
clock-frequency = <100000>;
|
|
status = "okay";
|
|
};
|
|
|
|
&nand {
|
|
status = "okay";
|
|
label = "pxa3xx_nand-0";
|
|
num-cs = <1>;
|
|
marvell,nand-keep-config;
|
|
nand-on-flash-bbt;
|
|
nand-ecc-strength = <4>;
|
|
nand-ecc-step-size = <512>;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
spi-flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "m25p64";
|
|
reg = <0>; /* Chip select 0 */
|
|
spi-max-frequency = <20000000>;
|
|
m25p,fast-read;
|
|
|
|
partition@u-boot {
|
|
reg = <0x00000000 0x00100000>;
|
|
label = "u-boot";
|
|
};
|
|
partition@u-boot-env {
|
|
reg = <0x00100000 0x00040000>;
|
|
label = "u-boot-env";
|
|
};
|
|
partition@unused {
|
|
reg = <0x00140000 0x00ec0000>;
|
|
label = "unused";
|
|
};
|
|
|
|
};
|
|
};
|