mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-30 07:16:43 +07:00
dcce6ce802
Because of the inclusion of skeleton.dtsi, the memory node is named "memory" we where not modifying the already included one but creating a new one. It caused bad memory node detection during early_init_dt_scan_memory() so we modify them. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: devicetree-discuss@lists.ozlabs.org
157 lines
2.5 KiB
Plaintext
157 lines
2.5 KiB
Plaintext
/*
|
|
* at91sam9m10g45ek.dts - Device Tree file for AT91SAM9M10G45-EK board
|
|
*
|
|
* Copyright (C) 2011 Atmel,
|
|
* 2011 Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
*
|
|
* Licensed under GPLv2 or later.
|
|
*/
|
|
/dts-v1/;
|
|
/include/ "at91sam9g45.dtsi"
|
|
|
|
/ {
|
|
model = "Atmel AT91SAM9M10G45-EK";
|
|
compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9";
|
|
|
|
chosen {
|
|
bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
|
|
};
|
|
|
|
memory {
|
|
reg = <0x70000000 0x4000000>;
|
|
};
|
|
|
|
clocks {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
main_clock: clock@0 {
|
|
compatible = "atmel,osc", "fixed-clock";
|
|
clock-frequency = <12000000>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
apb {
|
|
dbgu: serial@ffffee00 {
|
|
status = "okay";
|
|
};
|
|
|
|
usart1: serial@fff90000 {
|
|
status = "okay";
|
|
};
|
|
|
|
macb0: ethernet@fffbc000 {
|
|
phy-mode = "rmii";
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
nand0: nand@40000000 {
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "soft";
|
|
nand-on-flash-bbt;
|
|
status = "okay";
|
|
|
|
boot@0 {
|
|
label = "bootstrap/uboot/kernel";
|
|
reg = <0x0 0x400000>;
|
|
};
|
|
|
|
rootfs@400000 {
|
|
label = "rootfs";
|
|
reg = <0x400000 0x3C00000>;
|
|
};
|
|
|
|
data@4000000 {
|
|
label = "data";
|
|
reg = <0x4000000 0xC000000>;
|
|
};
|
|
};
|
|
|
|
usb0: ohci@00700000 {
|
|
status = "okay";
|
|
num-ports = <2>;
|
|
atmel,vbus-gpio = <&pioD 1 1
|
|
&pioD 3 1>;
|
|
};
|
|
|
|
usb1: ehci@00800000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
d8 {
|
|
label = "d8";
|
|
gpios = <&pioD 30 0>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
|
|
d6 {
|
|
label = "d6";
|
|
gpios = <&pioD 0 1>;
|
|
linux,default-trigger = "nand-disk";
|
|
};
|
|
|
|
d7 {
|
|
label = "d7";
|
|
gpios = <&pioD 31 1>;
|
|
linux,default-trigger = "mmc0";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
left_click {
|
|
label = "left_click";
|
|
gpios = <&pioB 6 1>;
|
|
linux,code = <272>;
|
|
gpio-key,wakeup;
|
|
};
|
|
|
|
right_click {
|
|
label = "right_click";
|
|
gpios = <&pioB 7 1>;
|
|
linux,code = <273>;
|
|
gpio-key,wakeup;
|
|
};
|
|
|
|
left {
|
|
label = "Joystick Left";
|
|
gpios = <&pioB 14 1>;
|
|
linux,code = <105>;
|
|
};
|
|
|
|
right {
|
|
label = "Joystick Right";
|
|
gpios = <&pioB 15 1>;
|
|
linux,code = <106>;
|
|
};
|
|
|
|
up {
|
|
label = "Joystick Up";
|
|
gpios = <&pioB 16 1>;
|
|
linux,code = <103>;
|
|
};
|
|
|
|
down {
|
|
label = "Joystick Down";
|
|
gpios = <&pioB 17 1>;
|
|
linux,code = <108>;
|
|
};
|
|
|
|
enter {
|
|
label = "Joystick Press";
|
|
gpios = <&pioB 18 1>;
|
|
linux,code = <28>;
|
|
};
|
|
};
|
|
};
|