linux_dsm_epyc7002/drivers/memory/Kconfig
Alex Smith 911a888297 memory: jz4780-nemc: driver for the NEMC on JZ4780 SoCs
Add a driver for the NAND/External Memory Controller (NEMC) on JZ4780
and later SoCs.

The primary function of this driver is to configure parameters, such
as timings, for external memory devices using data supplied in the
device tree. Devices connected to the NEMC are represented in the DT
as children of the NEMC node, the driver uses optional properties
specified in these child nodes to configure the parameters of each
bank.

Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 23:51:36 +01:00

98 lines
3.1 KiB
Plaintext

#
# Memory devices
#
menuconfig MEMORY
bool "Memory Controller drivers"
if MEMORY
config ATMEL_SDRAMC
bool "Atmel (Multi-port DDR-)SDRAM Controller"
default y
depends on ARCH_AT91 && OF
help
This driver is for Atmel SDRAM Controller or Atmel Multi-port
DDR-SDRAM Controller available on Atmel AT91SAM9 and SAMA5 SoCs.
Starting with the at91sam9g45, this controller supports SDR, DDR and
LP-DDR memories.
config TI_AEMIF
tristate "Texas Instruments AEMIF driver"
depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
help
This driver is for the AEMIF module available in Texas Instruments
SoCs. AEMIF stands for Asynchronous External Memory Interface and
is intended to provide a glue-less interface to a variety of
asynchronuous memory devices like ASRAM, NOR and NAND memory. A total
of 256M bytes of any of these memories can be accessed at a given
time via four chip selects with 64M byte access per chip select.
config TI_EMIF
tristate "Texas Instruments EMIF driver"
depends on ARCH_OMAP2PLUS
select DDR
help
This driver is for the EMIF module available in Texas Instruments
SoCs. EMIF is an SDRAM controller that, based on its revision,
supports one or more of DDR2, DDR3, and LPDDR2 SDRAM protocols.
This driver takes care of only LPDDR2 memories presently. The
functions of the driver includes re-configuring AC timing
parameters and other settings during frequency, voltage and
temperature changes
config OMAP_GPMC
bool
help
This driver is for the General Purpose Memory Controller (GPMC)
present on Texas Instruments SoCs (e.g. OMAP2+). GPMC allows
interfacing to a variety of asynchronous as well as synchronous
memory drives like NOR, NAND, OneNAND, SRAM.
config MVEBU_DEVBUS
bool "Marvell EBU Device Bus Controller"
default y
depends on PLAT_ORION && OF
help
This driver is for the Device Bus controller available in some
Marvell EBU SoCs such as Discovery (mv78xx0), Orion (88f5xxx) and
Armada 370 and Armada XP. This controller allows to handle flash
devices such as NOR, NAND, SRAM, and FPGA.
config TEGRA20_MC
bool "Tegra20 Memory Controller(MC) driver"
default y
depends on ARCH_TEGRA_2x_SOC
help
This driver is for the Memory Controller(MC) module available
in Tegra20 SoCs, mainly for a address translation fault
analysis, especially for IOMMU/GART(Graphics Address
Relocation Table) module.
config FSL_CORENET_CF
tristate "Freescale CoreNet Error Reporting"
depends on FSL_SOC_BOOKE
help
Say Y for reporting of errors from the Freescale CoreNet
Coherency Fabric. Errors reported include accesses to
physical addresses that mapped by no local access window
(LAW) or an invalid LAW, as well as bad cache state that
represents a coherency violation.
config FSL_IFC
bool
depends on FSL_SOC
config JZ4780_NEMC
bool "Ingenic JZ4780 SoC NEMC driver"
default y
depends on MACH_JZ4780
help
This driver is for the NAND/External Memory Controller (NEMC) in
the Ingenic JZ4780. This controller is used to handle external
memory devices such as NAND and SRAM.
source "drivers/memory/tegra/Kconfig"
endif