mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-27 06:45:09 +07:00
3290aa63ee
The Cadence MIPI-CSI2 RX controller is a CSI2RX bridge that supports up to 4 CSI-2 lanes, and can route the frames to up to 4 streams, depending on the hardware implementation. It can operate with an external D-PHY, an internal one or no D-PHY at all in some configurations. Acked-by: Rob Herring <robh@kernel.org> Acked-by: Benoit Parrot <bparrot@ti.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
101 lines
2.6 KiB
Plaintext
101 lines
2.6 KiB
Plaintext
Cadence MIPI-CSI2 RX controller
|
|
===============================
|
|
|
|
The Cadence MIPI-CSI2 RX controller is a CSI-2 bridge supporting up to 4 CSI
|
|
lanes in input, and 4 different pixel streams in output.
|
|
|
|
Required properties:
|
|
- compatible: must be set to "cdns,csi2rx" and an SoC-specific compatible
|
|
- reg: base address and size of the memory mapped region
|
|
- clocks: phandles to the clocks driving the controller
|
|
- clock-names: must contain:
|
|
* sys_clk: main clock
|
|
* p_clk: register bank clock
|
|
* pixel_if[0-3]_clk: pixel stream output clock, one for each stream
|
|
implemented in hardware, between 0 and 3
|
|
|
|
Optional properties:
|
|
- phys: phandle to the external D-PHY, phy-names must be provided
|
|
- phy-names: must contain "dphy", if the implementation uses an
|
|
external D-PHY
|
|
|
|
Required subnodes:
|
|
- ports: A ports node with one port child node per device input and output
|
|
port, in accordance with the video interface bindings defined in
|
|
Documentation/devicetree/bindings/media/video-interfaces.txt. The
|
|
port nodes are numbered as follows:
|
|
|
|
Port Description
|
|
-----------------------------
|
|
0 CSI-2 input
|
|
1 Stream 0 output
|
|
2 Stream 1 output
|
|
3 Stream 2 output
|
|
4 Stream 3 output
|
|
|
|
The stream output port nodes are optional if they are not
|
|
connected to anything at the hardware level or implemented
|
|
in the design.Since there is only one endpoint per port,
|
|
the endpoints are not numbered.
|
|
|
|
|
|
Example:
|
|
|
|
csi2rx: csi-bridge@0d060000 {
|
|
compatible = "cdns,csi2rx";
|
|
reg = <0x0d060000 0x1000>;
|
|
clocks = <&byteclock>, <&byteclock>
|
|
<&coreclock>, <&coreclock>,
|
|
<&coreclock>, <&coreclock>;
|
|
clock-names = "sys_clk", "p_clk",
|
|
"pixel_if0_clk", "pixel_if1_clk",
|
|
"pixel_if2_clk", "pixel_if3_clk";
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
|
|
csi2rx_in_sensor: endpoint {
|
|
remote-endpoint = <&sensor_out_csi2rx>;
|
|
clock-lanes = <0>;
|
|
data-lanes = <1 2>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
|
|
csi2rx_out_grabber0: endpoint {
|
|
remote-endpoint = <&grabber0_in_csi2rx>;
|
|
};
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
|
|
csi2rx_out_grabber1: endpoint {
|
|
remote-endpoint = <&grabber1_in_csi2rx>;
|
|
};
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
|
|
csi2rx_out_grabber2: endpoint {
|
|
remote-endpoint = <&grabber2_in_csi2rx>;
|
|
};
|
|
};
|
|
|
|
port@4 {
|
|
reg = <4>;
|
|
|
|
csi2rx_out_grabber3: endpoint {
|
|
remote-endpoint = <&grabber3_in_csi2rx>;
|
|
};
|
|
};
|
|
};
|
|
};
|