AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-28 11:18:45 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
425ab03675
linux_dsm_epyc7002/drivers/hwmon/Kconfig
Serge Semin 87976ce282 hwmon: Add Baikal-T1 PVT sensor driver 
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.

The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.

The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.

Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 07:59:45 -07:00

2076 lines
63 KiB
Plaintext
Raw Blame History

# SPDX-License-Identifier: GPL-2.0-only
#
# Hardware monitoring chip drivers configuration
#
menuconfig HWMON
tristate "Hardware Monitoring support"
depends on HAS_IOMEM
default y
help
Hardware monitoring devices let you monitor the hardware health
of a system. Most modern motherboards include such a device. It
can include temperature sensors, voltage sensors, fan speed
sensors and various additional features such as the ability to
control the speed of the fans. If you want this support you
should say Y here and also to the specific driver(s) for your
sensors chip(s) below.
To find out which specific driver(s) you need, use the
sensors-detect script from the lm_sensors package. Read
<file:Documentation/hwmon/userspace-tools.rst> for details.
This support can also be built as a module. If so, the module
will be called hwmon.
if HWMON
config HWMON_VID
tristate
config HWMON_DEBUG_CHIP
bool "Hardware Monitoring Chip debugging messages"
help
Say Y here if you want the I2C chip drivers to produce a bunch of
debug messages to the system log. Select this if you are having
a problem with I2C support and want to see more of what is going
on.
comment "Native drivers"
config SENSORS_AB8500
tristate "AB8500 thermal monitoring"
depends on AB8500_GPADC && AB8500_BM && (IIO = y)
default n
help
If you say yes here you get support for the thermal sensor part
of the AB8500 chip. The driver includes thermal management for
AB8500 die and two GPADC channels. The GPADC channel are preferably
used to access sensors outside the AB8500 chip.
This driver can also be built as a module. If so, the module
will be called abx500-temp.
config SENSORS_ABITUGURU
tristate "Abit uGuru (rev 1 & 2)"
depends on X86 && DMI
help
If you say yes here you get support for the sensor part of the first
and second revision of the Abit uGuru chip. The voltage and frequency
control parts of the Abit uGuru are not supported. The Abit uGuru
chip can be found on Abit uGuru featuring motherboards (most modern
Abit motherboards from before end 2005). For more info and a list
of which motherboards have which revision see
Documentation/hwmon/abituguru.rst
This driver can also be built as a module. If so, the module
will be called abituguru.
config SENSORS_ABITUGURU3
tristate "Abit uGuru (rev 3)"
depends on X86 && DMI
help
If you say yes here you get support for the sensor part of the
third revision of the Abit uGuru chip. Only reading the sensors
and their settings is supported. The third revision of the Abit
uGuru chip can be found on recent Abit motherboards (since end
2005). For more info and a list of which motherboards have which
revision see Documentation/hwmon/abituguru3.rst
This driver can also be built as a module. If so, the module
will be called abituguru3.
config SENSORS_AD7314
tristate "Analog Devices AD7314 and compatibles"
depends on SPI
help
If you say yes here you get support for the Analog Devices
AD7314, ADT7301 and ADT7302 temperature sensors.
This driver can also be built as a module. If so, the module
will be called ad7314.
config SENSORS_AD7414
tristate "Analog Devices AD7414"
depends on I2C
help
If you say yes here you get support for the Analog Devices
AD7414 temperature monitoring chip.
This driver can also be built as a module. If so, the module
will be called ad7414.
config SENSORS_AD7418
tristate "Analog Devices AD7416, AD7417 and AD7418"
depends on I2C
help
If you say yes here you get support for the Analog Devices
AD7416, AD7417 and AD7418 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called ad7418.
config SENSORS_ADM1021
tristate "Analog Devices ADM1021 and compatibles"
depends on I2C
help
If you say yes here you get support for Analog Devices ADM1021
and ADM1023 sensor chips and clones: Maxim MAX1617 and MAX1617A,
Genesys Logic GL523SM, National Semiconductor LM84 and TI THMC10.
This driver can also be built as a module. If so, the module
will be called adm1021.
config SENSORS_ADM1025
tristate "Analog Devices ADM1025 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1025
and Philips NE1619 sensor chips.
This driver can also be built as a module. If so, the module
will be called adm1025.
config SENSORS_ADM1026
tristate "Analog Devices ADM1026 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1026
sensor chip.
This driver can also be built as a module. If so, the module
will be called adm1026.
config SENSORS_ADM1029
tristate "Analog Devices ADM1029"
depends on I2C
help
If you say yes here you get support for Analog Devices ADM1029
sensor chip.
Very rare chip, please let us know you use it.
This driver can also be built as a module. If so, the module
will be called adm1029.
config SENSORS_ADM1031
tristate "Analog Devices ADM1031 and compatibles"
depends on I2C
help
If you say yes here you get support for Analog Devices ADM1031
and ADM1030 sensor chips.
This driver can also be built as a module. If so, the module
will be called adm1031.
config SENSORS_ADM1177
tristate "Analog Devices ADM1177 and compatibles"
depends on I2C
help
If you say yes here you get support for Analog Devices ADM1177
sensor chips.
This driver can also be built as a module. If so, the module
will be called adm1177.
config SENSORS_ADM9240
tristate "Analog Devices ADM9240 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM9240,
Dallas DS1780, National Semiconductor LM81 sensor chips.
This driver can also be built as a module. If so, the module
will be called adm9240.
config SENSORS_ADT7X10
tristate
help
This module contains common code shared by the ADT7310/ADT7320 and
ADT7410/ADT7420 temperature monitoring chip drivers.
If built as a module, the module will be called adt7x10.
config SENSORS_ADT7310
tristate "Analog Devices ADT7310/ADT7320"
depends on SPI_MASTER
select SENSORS_ADT7X10
help
If you say yes here you get support for the Analog Devices
ADT7310 and ADT7320 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called adt7310.
config SENSORS_ADT7410
tristate "Analog Devices ADT7410/ADT7420"
depends on I2C
select SENSORS_ADT7X10
help
If you say yes here you get support for the Analog Devices
ADT7410 and ADT7420 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called adt7410.
config SENSORS_ADT7411
tristate "Analog Devices ADT7411"
depends on I2C
help
If you say yes here you get support for the Analog Devices
ADT7411 voltage and temperature monitoring chip.
This driver can also be built as a module. If so, the module
will be called adt7411.
config SENSORS_ADT7462
tristate "Analog Devices ADT7462"
depends on I2C
help
If you say yes here you get support for the Analog Devices
ADT7462 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called adt7462.
config SENSORS_ADT7470
tristate "Analog Devices ADT7470"
depends on I2C
help
If you say yes here you get support for the Analog Devices
ADT7470 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called adt7470.
config SENSORS_ADT7475
tristate "Analog Devices ADT7473, ADT7475, ADT7476 and ADT7490"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Analog Devices
ADT7473, ADT7475, ADT7476 and ADT7490 hardware monitoring
chips.
This driver can also be built as a module. If so, the module
will be called adt7475.
config SENSORS_AS370
tristate "Synaptics AS370 SoC hardware monitoring driver"
help
If you say yes here you get support for the PVT sensors of
the Synaptics AS370 SoC
This driver can also be built as a module. If so, the module
will be called as370-hwmon.
config SENSORS_ASC7621
tristate "Andigilog aSC7621"
depends on I2C
help
If you say yes here you get support for the aSC7621
family of SMBus sensors chip found on most Intel X38, X48, X58,
945, 965 and 975 desktop boards. Currently supported chips:
aSC7621
aSC7621a
This driver can also be built as a module. If so, the module
will be called asc7621.
config SENSORS_AXI_FAN_CONTROL
tristate "Analog Devices FAN Control HDL Core driver"
help
If you say yes here you get support for the Analog Devices
AXI HDL FAN monitoring core.
This driver can also be built as a module. If so, the module
will be called axi-fan-control
config SENSORS_K8TEMP
tristate "AMD Athlon64/FX or Opteron temperature sensor"
depends on X86 && PCI
help
If you say yes here you get support for the temperature
sensor(s) inside your CPU. Supported is whole AMD K8
microarchitecture. Please note that you will need at least
lm-sensors 2.10.1 for proper userspace support.
This driver can also be built as a module. If so, the module
will be called k8temp.
config SENSORS_K10TEMP
tristate "AMD Family 10h+ temperature sensor"
depends on X86 && PCI && AMD_NB
help
If you say yes here you get support for the temperature
sensor(s) inside your CPU. Supported are later revisions of
the AMD Family 10h and all revisions of the AMD Family 11h,
12h (Llano), 14h (Brazos), 15h (Bulldozer/Trinity/Kaveri/Carrizo)
and 16h (Kabini/Mullins) microarchitectures.
This driver can also be built as a module. If so, the module
will be called k10temp.
config SENSORS_FAM15H_POWER
tristate "AMD Family 15h processor power"
depends on X86 && PCI && CPU_SUP_AMD
help
If you say yes here you get support for processor power
information of your AMD family 15h CPU.
This driver can also be built as a module. If so, the module
will be called fam15h_power.
config SENSORS_AMD_ENERGY
tristate "AMD RAPL MSR based Energy driver"
depends on X86
help
If you say yes here you get support for core and package energy
sensors, based on RAPL MSR for AMD family 17h and above CPUs.
This driver can also be built as a module. If so, the module
will be called as amd_energy.
config SENSORS_APPLESMC
tristate "Apple SMC (Motion sensor, light sensor, keyboard backlight)"
depends on INPUT && X86
select NEW_LEDS
select LEDS_CLASS
help
This driver provides support for the Apple System Management
Controller, which provides an accelerometer (Apple Sudden Motion
Sensor), light sensors, temperature sensors, keyboard backlight
control and fan control.
Only Intel-based Apple's computers are supported (MacBook Pro,
MacBook, MacMini).
Data from the different sensors, keyboard backlight control and fan
control are accessible via sysfs.
This driver also provides an absolute input class device, allowing
the laptop to act as a pinball machine-esque joystick.
Say Y here if you have an applicable laptop and want to experience
the awesome power of applesmc.
config SENSORS_ARM_SCMI
tristate "ARM SCMI Sensors"
depends on ARM_SCMI_PROTOCOL
depends on THERMAL || !THERMAL_OF
help
This driver provides support for temperature, voltage, current
and power sensors available on SCMI based platforms. The actual
number and type of sensors exported depend on the platform.
This driver can also be built as a module. If so, the module
will be called scmi-hwmon.
config SENSORS_ARM_SCPI
tristate "ARM SCPI Sensors"
depends on ARM_SCPI_PROTOCOL
depends on THERMAL || !THERMAL_OF
help
This driver provides support for temperature, voltage, current
and power sensors available on ARM Ltd's SCP based platforms. The
actual number and type of sensors exported depend on the platform.
config SENSORS_ASB100
tristate "Asus ASB100 Bach"
depends on X86 && I2C
select HWMON_VID
help
If you say yes here you get support for the ASB100 Bach sensor
chip found on some Asus mainboards.
This driver can also be built as a module. If so, the module
will be called asb100.
config SENSORS_ASPEED
tristate "ASPEED AST2400/AST2500 PWM and Fan tach driver"
depends on THERMAL || THERMAL=n
select REGMAP
help
This driver provides support for ASPEED AST2400/AST2500 PWM
and Fan Tacho controllers.
This driver can also be built as a module. If so, the module
will be called aspeed_pwm_tacho.
config SENSORS_ATXP1
tristate "Attansic ATXP1 VID controller"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Attansic ATXP1 VID
controller.
If your board have such a chip, you are able to control your CPU
core and other voltages.
This driver can also be built as a module. If so, the module
will be called atxp1.
config SENSORS_BT1_PVT
tristate "Baikal-T1 Process, Voltage, Temperature sensor driver"
depends on MIPS_BAIKAL_T1 || COMPILE_TEST
help
If you say yes here you get support for Baikal-T1 PVT sensor
embedded into the SoC.
This driver can also be built as a module. If so, the module will be
called bt1-pvt.
config SENSORS_BT1_PVT_ALARMS
bool "Enable Baikal-T1 PVT sensor alarms"
depends on SENSORS_BT1_PVT
help
Baikal-T1 PVT IP-block provides threshold registers for each
supported sensor. But the corresponding interrupts might be
generated by the thresholds comparator only in synchronization with
a data conversion. Additionally there is only one sensor data can
be converted at a time. All of these makes the interface impossible
to be used for the hwmon alarms implementation without periodic
switch between the PVT sensors. By default the data conversion is
performed on demand from the user-space. If this config is enabled
the data conversion will be periodically performed and the data will be
saved in the internal driver cache.
config SENSORS_DRIVETEMP
tristate "Hard disk drives with temperature sensors"
depends on SCSI && ATA
help
If you say yes you get support for the temperature sensor on
hard disk drives.
This driver can also be built as a module. If so, the module
will be called drivetemp.
config SENSORS_DS620
tristate "Dallas Semiconductor DS620"
depends on I2C
help
If you say yes here you get support for Dallas Semiconductor
DS620 sensor chip.
This driver can also be built as a module. If so, the module
will be called ds620.
config SENSORS_DS1621
tristate "Dallas Semiconductor DS1621 and compatibles"
depends on I2C
help
If you say yes here you get support for Dallas Semiconductor/Maxim
Integrated DS1621 sensor chips and compatible models including:
- Dallas Semiconductor DS1625
- Maxim Integrated DS1631
- Maxim Integrated DS1721
- Maxim Integrated DS1731
This driver can also be built as a module. If so, the module
will be called ds1621.
config SENSORS_DELL_SMM
tristate "Dell laptop SMM BIOS hwmon driver"
depends on X86
help
This hwmon driver adds support for reporting temperature of different
sensors and controls the fans on Dell laptops via System Management
Mode provided by Dell BIOS.
When option I8K is also enabled this driver provides legacy /proc/i8k
userspace interface for i8kutils package.
config SENSORS_DA9052_ADC
tristate "Dialog DA9052/DA9053 ADC"
depends on PMIC_DA9052
help
Say y here to support the ADC found on Dialog Semiconductor
DA9052-BC and DA9053-AA/Bx PMICs.
This driver can also be built as module. If so, the module
will be called da9052-hwmon.
config SENSORS_DA9055
tristate "Dialog Semiconductor DA9055 ADC"
depends on MFD_DA9055
help
If you say yes here you get support for ADC on the Dialog
Semiconductor DA9055 PMIC.
This driver can also be built as a module. If so, the module
will be called da9055-hwmon.
config SENSORS_I5K_AMB
tristate "FB-DIMM AMB temperature sensor on Intel 5000 series chipsets"
depends on PCI
help
If you say yes here you get support for FB-DIMM AMB temperature
monitoring chips on systems with the Intel 5000 series chipset.
This driver can also be built as a module. If so, the module
will be called i5k_amb.
config SENSORS_F71805F
tristate "Fintek F71805F/FG, F71806F/FG and F71872F/FG"
depends on !PPC
help
If you say yes here you get support for hardware monitoring
features of the Fintek F71805F/FG, F71806F/FG and F71872F/FG
Super-I/O chips.
This driver can also be built as a module. If so, the module
will be called f71805f.
config SENSORS_F71882FG
tristate "Fintek F71882FG and compatibles"
depends on !PPC
help
If you say yes here you get support for hardware monitoring
features of many Fintek Super-I/O (LPC) chips. The currently
supported chips are:
F71808E/A
F71858FG
F71862FG
F71863FG
F71869F/E/A
F71882FG
F71883FG
F71889FG/ED/A
F8000
F81801U
F81865F
This driver can also be built as a module. If so, the module
will be called f71882fg.
config SENSORS_F75375S
tristate "Fintek F75375S/SP, F75373 and F75387"
depends on I2C
help
If you say yes here you get support for hardware monitoring
features of the Fintek F75375S/SP, F75373 and F75387
This driver can also be built as a module. If so, the module
will be called f75375s.
config SENSORS_GSC
tristate "Gateworks System Controller ADC"
depends on MFD_GATEWORKS_GSC
help
Support for the Gateworks System Controller A/D converters.
To compile this driver as a module, choose M here:
the module will be called gsc-hwmon.
config SENSORS_MC13783_ADC
tristate "Freescale MC13783/MC13892 ADC"
depends on MFD_MC13XXX
help
Support for the A/D converter on MC13783 and MC13892 PMIC.
config SENSORS_FSCHMD
tristate "Fujitsu Siemens Computers sensor chips"
depends on X86 && I2C
help
If you say yes here you get support for the following Fujitsu
Siemens Computers (FSC) sensor chips: Poseidon, Scylla, Hermes,
Heimdall, Heracles, Hades and Syleus including support for the
integrated watchdog.
This is a merged driver for FSC sensor chips replacing the fscpos,
fscscy and fscher drivers and adding support for several other FSC
sensor chips.
This driver can also be built as a module. If so, the module
will be called fschmd.
config SENSORS_FTSTEUTATES
tristate "Fujitsu Technology Solutions sensor chip Teutates"
depends on I2C && WATCHDOG
select WATCHDOG_CORE
help
If you say yes here you get support for the Fujitsu Technology
Solutions (FTS) sensor chip "Teutates" including support for
the integrated watchdog.
This driver can also be built as a module. If so, the module
will be called ftsteutates.
config SENSORS_GL518SM
tristate "Genesys Logic GL518SM"
depends on I2C
help
If you say yes here you get support for Genesys Logic GL518SM
sensor chips.
This driver can also be built as a module. If so, the module
will be called gl518sm.
config SENSORS_GL520SM
tristate "Genesys Logic GL520SM"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for Genesys Logic GL520SM
sensor chips.
This driver can also be built as a module. If so, the module
will be called gl520sm.
config SENSORS_G760A
tristate "GMT G760A"
depends on I2C
help
If you say yes here you get support for Global Mixed-mode
Technology Inc G760A fan speed PWM controller chips.
This driver can also be built as a module. If so, the module
will be called g760a.
config SENSORS_G762
tristate "GMT G762 and G763"
depends on I2C
help
If you say yes here you get support for Global Mixed-mode
Technology Inc G762 and G763 fan speed PWM controller chips.
This driver can also be built as a module. If so, the module
will be called g762.
config SENSORS_GPIO_FAN
tristate "GPIO fan"
depends on OF_GPIO
depends on GPIOLIB || COMPILE_TEST
depends on THERMAL || THERMAL=n
help
If you say yes here you get support for fans connected to GPIO lines.
This driver can also be built as a module. If so, the module
will be called gpio-fan.
config SENSORS_HIH6130
tristate "Honeywell Humidicon HIH-6130 humidity/temperature sensor"
depends on I2C
help
If you say yes here you get support for Honeywell Humidicon
HIH-6130 and HIH-6131 Humidicon humidity sensors.
This driver can also be built as a module. If so, the module
will be called hih6130.
config SENSORS_IBMAEM
tristate "IBM Active Energy Manager temperature/power sensors and control"
select IPMI_SI
depends on IPMI_HANDLER
help
If you say yes here you get support for the temperature and
power sensors and capping hardware in various IBM System X
servers that support Active Energy Manager. This includes
the x3350, x3550, x3650, x3655, x3755, x3850 M2, x3950 M2,
and certain HC10/HS2x/LS2x/QS2x blades.
This driver can also be built as a module. If so, the module
will be called ibmaem.
config SENSORS_IBMPEX
tristate "IBM PowerExecutive temperature/power sensors"
select IPMI_SI
depends on IPMI_HANDLER
help
If you say yes here you get support for the temperature and
power sensors in various IBM System X servers that support
PowerExecutive. So far this includes the x3350, x3550, x3650,
x3655, and x3755; the x3800, x3850, and x3950 models that have
PCI Express; and some of the HS2x, LS2x, and QS2x blades.
This driver can also be built as a module. If so, the module
will be called ibmpex.
config SENSORS_IBMPOWERNV
tristate "IBM POWERNV platform sensors"
depends on PPC_POWERNV
default y
help
If you say yes here you get support for the temperature/fan/power
sensors on your PowerNV platform.
This driver can also be built as a module. If so, the module
will be called ibmpowernv.
config SENSORS_IIO_HWMON
tristate "Hwmon driver that uses channels specified via iio maps"
depends on IIO
help
This is a platform driver that in combination with a suitable
map allows IIO devices to provide basic hwmon functionality
for those channels specified in the map. This map can be provided
either via platform data or the device tree bindings.
config SENSORS_I5500
tristate "Intel 5500/5520/X58 temperature sensor"
depends on X86 && PCI
help
If you say yes here you get support for the temperature
sensor inside the Intel 5500, 5520 and X58 chipsets.
This driver can also be built as a module. If so, the module
will be called i5500_temp.
config SENSORS_CORETEMP
tristate "Intel Core/Core2/Atom temperature sensor"
depends on X86
help
If you say yes here you get support for the temperature
sensor inside your CPU. Most of the family 6 CPUs
are supported. Check Documentation/hwmon/coretemp.rst for details.
config SENSORS_IT87
tristate "ITE IT87xx and compatibles"
depends on !PPC
select HWMON_VID
help
If you say yes here you get support for ITE IT8705F, IT8712F, IT8716F,
IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8732F, IT8758E,
IT8771E, IT8772E, IT8781F, IT8782F, IT8783E/F, IT8786E, IT8790E,
IT8603E, IT8620E, IT8623E, and IT8628E sensor chips, and the SiS950
clone.
This driver can also be built as a module. If so, the module
will be called it87.
config SENSORS_JC42
tristate "JEDEC JC42.4 compliant memory module temperature sensors"
depends on I2C
help
If you say yes here, you get support for JEDEC JC42.4 compliant
temperature sensors, which are used on many DDR3 memory modules for
mobile devices and servers. Support will include, but not be limited
to, ADT7408, AT30TS00, CAT34TS02, CAT6095, MAX6604, MCP9804, MCP9805,
MCP9808, MCP98242, MCP98243, MCP98244, MCP9843, SE97, SE98,
STTS424(E), STTS2002, STTS3000, TSE2002, TSE2004, TS3000, and TS3001.
This driver can also be built as a module. If so, the module
will be called jc42.
config SENSORS_POWR1220
tristate "Lattice POWR1220 Power Monitoring"
depends on I2C
help
If you say yes here you get access to the hardware monitoring
functions of the Lattice POWR1220 isp Power Supply Monitoring,
Sequencing and Margining Controller.
This driver can also be built as a module. If so, the module
will be called powr1220.
config SENSORS_LINEAGE
tristate "Lineage Compact Power Line Power Entry Module"
depends on I2C
help
If you say yes here you get support for the Lineage Compact Power Line
series of DC/DC and AC/DC converters such as CP1800, CP2000AC,
CP2000DC, CP2725, and others.
This driver can also be built as a module. If so, the module
will be called lineage-pem.
config SENSORS_LOCHNAGAR
tristate "Lochnagar Hardware Monitor"
depends on MFD_LOCHNAGAR
help
If you say yes here you get support for Lochnagar 2 temperature,
voltage and current sensors abilities.
This driver can also be built as a module. If so, the module
will be called lochnagar-hwmon.
config SENSORS_LTC2945
tristate "Linear Technology LTC2945"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for Linear Technology LTC2945
I2C System Monitor.
This driver can also be built as a module. If so, the module will
be called ltc2945.
config SENSORS_LTC2947
tristate
config SENSORS_LTC2947_I2C
tristate "Analog Devices LTC2947 High Precision Power and Energy Monitor over I2C"
depends on I2C
select REGMAP_I2C
select SENSORS_LTC2947
help
If you say yes here you get support for Linear Technology LTC2947
I2C High Precision Power and Energy Monitor
This driver can also be built as a module. If so, the module will
be called ltc2947-i2c.
config SENSORS_LTC2947_SPI
tristate "Analog Devices LTC2947 High Precision Power and Energy Monitor over SPI"
depends on SPI_MASTER
select REGMAP_SPI
select SENSORS_LTC2947
help
If you say yes here you get support for Linear Technology LTC2947
SPI High Precision Power and Energy Monitor
This driver can also be built as a module. If so, the module will
be called ltc2947-spi.
config SENSORS_LTC2990
tristate "Linear Technology LTC2990"
depends on I2C
help
If you say yes here you get support for Linear Technology LTC2990
I2C System Monitor. The LTC2990 supports a combination of voltage,
current and temperature monitoring.
This driver can also be built as a module. If so, the module will
be called ltc2990.
config SENSORS_LTC4151
tristate "Linear Technology LTC4151"
depends on I2C
help
If you say yes here you get support for Linear Technology LTC4151
High Voltage I2C Current and Voltage Monitor interface.
This driver can also be built as a module. If so, the module will
be called ltc4151.
config SENSORS_LTC4215
tristate "Linear Technology LTC4215"
depends on I2C
help
If you say yes here you get support for Linear Technology LTC4215
Hot Swap Controller I2C interface.
This driver can also be built as a module. If so, the module will
be called ltc4215.
config SENSORS_LTC4222
tristate "Linear Technology LTC4222"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for Linear Technology LTC4222
Dual Hot Swap Controller I2C interface.
This driver can also be built as a module. If so, the module will
be called ltc4222.
config SENSORS_LTC4245
tristate "Linear Technology LTC4245"
depends on I2C
help
If you say yes here you get support for Linear Technology LTC4245
Multiple Supply Hot Swap Controller I2C interface.
This driver can also be built as a module. If so, the module will
be called ltc4245.
config SENSORS_LTC4260
tristate "Linear Technology LTC4260"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for Linear Technology LTC4260
Positive Voltage Hot Swap Controller I2C interface.
This driver can also be built as a module. If so, the module will
be called ltc4260.
config SENSORS_LTC4261
tristate "Linear Technology LTC4261"
depends on I2C
help
If you say yes here you get support for Linear Technology LTC4261
Negative Voltage Hot Swap Controller I2C interface.
This driver can also be built as a module. If so, the module will
be called ltc4261.
config SENSORS_LTQ_CPUTEMP
bool "Lantiq cpu temperature sensor driver"
depends on LANTIQ
help
If you say yes here you get support for the temperature
sensor inside your CPU.
config SENSORS_MAX1111
tristate "Maxim MAX1111 Serial 8-bit ADC chip and compatibles"
depends on SPI_MASTER
help
Say y here to support Maxim's MAX1110, MAX1111, MAX1112, and MAX1113
ADC chips.
This driver can also be built as a module. If so, the module
will be called max1111.
config SENSORS_MAX16065
tristate "Maxim MAX16065 System Manager and compatibles"
depends on I2C
help
If you say yes here you get support for hardware monitoring
capabilities of the following Maxim System Manager chips.
MAX16065
MAX16066
MAX16067
MAX16068
MAX16070
MAX16071
This driver can also be built as a module. If so, the module
will be called max16065.
config SENSORS_MAX1619
tristate "Maxim MAX1619 sensor chip"
depends on I2C
help
If you say yes here you get support for MAX1619 sensor chip.
This driver can also be built as a module. If so, the module
will be called max1619.
config SENSORS_MAX1668
tristate "Maxim MAX1668 and compatibles"
depends on I2C
help
If you say yes here you get support for MAX1668, MAX1989 and
MAX1805 chips.
This driver can also be built as a module. If so, the module
will be called max1668.
config SENSORS_MAX197
tristate "Maxim MAX197 and compatibles"
help
Support for the Maxim MAX197 A/D converter.
Support will include, but not be limited to, MAX197, and MAX199.
This driver can also be built as a module. If so, the module
will be called max197.
config SENSORS_MAX31722
tristate "MAX31722 temperature sensor"
depends on SPI
help
Support for the Maxim Integrated MAX31722/MAX31723 digital
thermometers/thermostats operating over an SPI interface.
This driver can also be built as a module. If so, the module
will be called max31722.
config SENSORS_MAX31730
tristate "MAX31730 temperature sensor"
depends on I2C
help
Support for the Maxim Integrated MAX31730 3-Channel Remote
Temperature Sensor.
This driver can also be built as a module. If so, the module
will be called max31730.
config SENSORS_MAX6621
tristate "Maxim MAX6621 sensor chip"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for MAX6621 sensor chip.
MAX6621 is a PECI-to-I2C translator provides an efficient,
low-cost solution for PECI-to-SMBus/I2C protocol conversion.
It allows reading the temperature from the PECI-compliant
host directly from up to four PECI-enabled CPUs.
This driver can also be built as a module. If so, the module
will be called max6621.
config SENSORS_MAX6639
tristate "Maxim MAX6639 sensor chip"
depends on I2C
help
If you say yes here you get support for the MAX6639
sensor chips.
This driver can also be built as a module. If so, the module
will be called max6639.
config SENSORS_MAX6642
tristate "Maxim MAX6642 sensor chip"
depends on I2C
help
If you say yes here you get support for MAX6642 sensor chip.
MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor
with Overtemperature Alarm from Maxim.
This driver can also be built as a module. If so, the module
will be called max6642.
config SENSORS_MAX6650
tristate "Maxim MAX6650 sensor chip"
depends on I2C
depends on THERMAL || THERMAL=n
help
If you say yes here you get support for the MAX6650 / MAX6651
sensor chips.
This driver can also be built as a module. If so, the module
will be called max6650.
config SENSORS_MAX6697
tristate "Maxim MAX6697 and compatibles"
depends on I2C
help
If you say yes here you get support for MAX6581, MAX6602, MAX6622,
MAX6636, MAX6689, MAX6693, MAX6694, MAX6697, MAX6698, and MAX6699
temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called max6697.
config SENSORS_MAX31790
tristate "Maxim MAX31790 sensor chip"
depends on I2C
help
If you say yes here you get support for 6-Channel PWM-Output
Fan RPM Controller.
This driver can also be built as a module. If so, the module
will be called max31790.
config SENSORS_MCP3021
tristate "Microchip MCP3021 and compatibles"
depends on I2C
help
If you say yes here you get support for MCP3021 and MCP3221.
The MCP3021 is a A/D converter (ADC) with 10-bit and the MCP3221
with 12-bit resolution.
This driver can also be built as a module. If so, the module
will be called mcp3021.
config SENSORS_MLXREG_FAN
tristate "Mellanox Mellanox FAN driver"
depends on MELLANOX_PLATFORM
imply THERMAL
select REGMAP
help
This option enables support for the FAN control on the Mellanox
Ethernet and InfiniBand switches. The driver can be activated by the
platform device add call. Say Y to enable these. To compile this
driver as a module, choose 'M' here: the module will be called
mlxreg-fan.
config SENSORS_TC654
tristate "Microchip TC654/TC655 and compatibles"
depends on I2C
help
If you say yes here you get support for TC654 and TC655.
The TC654 and TC655 are PWM mode fan speed controllers with
FanSense technology for use with brushless DC fans.
This driver can also be built as a module. If so, the module
will be called tc654.
config SENSORS_MENF21BMC_HWMON
tristate "MEN 14F021P00 BMC Hardware Monitoring"
depends on MFD_MENF21BMC
help
Say Y here to include support for the MEN 14F021P00 BMC
hardware monitoring.
This driver can also be built as a module. If so the module
will be called menf21bmc_hwmon.
config SENSORS_ADCXX
tristate "National Semiconductor ADCxxxSxxx"
depends on SPI_MASTER
help
If you say yes here you get support for the National Semiconductor
ADC<bb><c>S<sss> chip family, where
* bb is the resolution in number of bits (8, 10, 12)
* c is the number of channels (1, 2, 4, 8)
* sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
kSPS and 101 for 1 MSPS)
Examples : ADC081S101, ADC124S501, ...
This driver can also be built as a module. If so, the module
will be called adcxx.
config SENSORS_LM63
tristate "National Semiconductor LM63 and compatibles"
depends on I2C
help
If you say yes here you get support for the National
Semiconductor LM63, LM64, and LM96163 remote diode digital temperature
sensors with integrated fan control. Such chips are found
on the Tyan S4882 (Thunder K8QS Pro) motherboard, among
others.
This driver can also be built as a module. If so, the module
will be called lm63.
config SENSORS_LM70
tristate "National Semiconductor LM70 and compatibles"
depends on SPI_MASTER
help
If you say yes here you get support for the National Semiconductor
LM70, LM71, LM74 and Texas Instruments TMP121/TMP123 digital tempera-
ture sensor chips.
This driver can also be built as a module. If so, the module
will be called lm70.
config SENSORS_LM73
tristate "National Semiconductor LM73"
depends on I2C
help
If you say yes here you get support for National Semiconductor LM73
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm73.
config SENSORS_LM75
tristate "National Semiconductor LM75 and compatibles"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for one common type of
temperature sensor chip, with models including:
- Analog Devices ADT75
- Dallas Semiconductor DS75, DS1775 and DS7505
- Global Mixed-mode Technology (GMT) G751
- Maxim MAX6625 and MAX6626
- Microchip MCP980x
- National Semiconductor LM75, LM75A
- NXP's LM75A
- ST Microelectronics STDS75
- ST Microelectronics STLM75
- TelCom (now Microchip) TCN75
- Texas Instruments TMP100, TMP101, TMP105, TMP112, TMP75,
TMP175, TMP275
This driver supports driver model based binding through board
specific I2C device tables.
It also supports the "legacy" style of driver binding. To use
that with some chips which don't replicate LM75 quirks exactly,
you may need the "force" module parameter.
This driver can also be built as a module. If so, the module
will be called lm75.
config SENSORS_LM77
tristate "National Semiconductor LM77"
depends on I2C
help
If you say yes here you get support for National Semiconductor LM77
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm77.
config SENSORS_LM78
tristate "National Semiconductor LM78 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM78,
LM78-J and LM79.
This driver can also be built as a module. If so, the module
will be called lm78.
config SENSORS_LM80
tristate "National Semiconductor LM80 and LM96080"
depends on I2C
help
If you say yes here you get support for National Semiconductor
LM80 and LM96080 sensor chips.
This driver can also be built as a module. If so, the module
will be called lm80.
config SENSORS_LM83
tristate "National Semiconductor LM83 and compatibles"
depends on I2C
help
If you say yes here you get support for National Semiconductor
LM82 and LM83 sensor chips.
This driver can also be built as a module. If so, the module
will be called lm83.
config SENSORS_LM85
tristate "National Semiconductor LM85 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM85
sensor chips and clones: ADM1027, ADT7463, ADT7468, EMC6D100,
EMC6D101, EMC6D102, and EMC6D103.
This driver can also be built as a module. If so, the module
will be called lm85.
config SENSORS_LM87
tristate "National Semiconductor LM87 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM87
and Analog Devices ADM1024 sensor chips.
This driver can also be built as a module. If so, the module
will be called lm87.
config SENSORS_LM90
tristate "National Semiconductor LM90 and compatibles"
depends on I2C
help
If you say yes here you get support for National Semiconductor LM90,
LM86, LM89 and LM99, Analog Devices ADM1032, ADT7461, and ADT7461A,
Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6654, MAX6657, MAX6658,
MAX6659, MAX6680, MAX6681, MAX6692, MAX6695, MAX6696,
ON Semiconductor NCT1008, Winbond/Nuvoton W83L771W/G/AWG/ASG,
Philips SA56004, GMT G781, and Texas Instruments TMP451
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm90.
config SENSORS_LM92
tristate "National Semiconductor LM92 and compatibles"
depends on I2C
help
If you say yes here you get support for National Semiconductor LM92
and Maxim MAX6635 sensor chips.
This driver can also be built as a module. If so, the module
will be called lm92.
config SENSORS_LM93
tristate "National Semiconductor LM93 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM93,
LM94, and compatible sensor chips.
This driver can also be built as a module. If so, the module
will be called lm93.
config SENSORS_LM95234
tristate "National Semiconductor LM95234 and compatibles"
depends on I2C
help
If you say yes here you get support for the LM95233 and LM95234
temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called lm95234.
config SENSORS_LM95241
tristate "National Semiconductor LM95241 and compatibles"
depends on I2C
help
If you say yes here you get support for LM95231 and LM95241 sensor
chips.
This driver can also be built as a module. If so, the module
will be called lm95241.
config SENSORS_LM95245
tristate "National Semiconductor LM95245 and compatibles"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for LM95235 and LM95245
temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called lm95245.
config SENSORS_PC87360
tristate "National Semiconductor PC87360 family"
depends on !PPC
select HWMON_VID
help
If you say yes here you get access to the hardware monitoring
functions of the National Semiconductor PC8736x Super-I/O chips.
The PC87360, PC87363 and PC87364 only have fan monitoring and
control. The PC87365 and PC87366 additionally have voltage and
temperature monitoring.
This driver can also be built as a module. If so, the module
will be called pc87360.
config SENSORS_PC87427
tristate "National Semiconductor PC87427"
depends on !PPC
help
If you say yes here you get access to the hardware monitoring
functions of the National Semiconductor PC87427 Super-I/O chip.
The chip has two distinct logical devices, one for fan speed
monitoring and control, and one for voltage and temperature
monitoring. Fan speed monitoring and control are supported, as
well as temperature monitoring. Voltages aren't supported yet.
This driver can also be built as a module. If so, the module
will be called pc87427.
config SENSORS_NTC_THERMISTOR
tristate "NTC thermistor support from Murata"
depends on !OF || IIO=n || IIO
depends on THERMAL || !THERMAL_OF
help
This driver supports NTC thermistors sensor reading and its
interpretation. The driver can also monitor the temperature and
send notifications about the temperature.
Currently, this driver supports
NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, NCP15WL333,
NCP03WF104 and NCP15XH103 from Murata and B57330V2103 and
B57891S0103 from EPCOS.
This driver can also be built as a module. If so, the module
will be called ntc-thermistor.
config SENSORS_NCT6683
tristate "Nuvoton NCT6683D"
depends on !PPC
help
If you say yes here you get support for the hardware monitoring
functionality of the Nuvoton NCT6683D eSIO chip.
This driver can also be built as a module. If so, the module
will be called nct6683.
config SENSORS_NCT6775
tristate "Nuvoton NCT6775F and compatibles"
depends on !PPC
select HWMON_VID
help
If you say yes here you get support for the hardware monitoring
functionality of the Nuvoton NCT6106D, NCT6775F, NCT6776F, NCT6779D,
NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D, and compatible
Super-I/O chips. This driver replaces the w83627ehf driver for
NCT6775F and NCT6776F.
This driver can also be built as a module. If so, the module
will be called nct6775.
config SENSORS_NCT7802
tristate "Nuvoton NCT7802Y"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for the Nuvoton NCT7802Y
hardware monitoring chip.
This driver can also be built as a module. If so, the module
will be called nct7802.
config SENSORS_NCT7904
tristate "Nuvoton NCT7904"
depends on I2C && WATCHDOG
select WATCHDOG_CORE
help
If you say yes here you get support for the Nuvoton NCT7904
hardware monitoring chip, including manual fan speed control
and support for the integrated watchdog.
This driver can also be built as a module. If so, the module
will be called nct7904.
config SENSORS_NPCM7XX
tristate "Nuvoton NPCM750 and compatible PWM and Fan controllers"
imply THERMAL
help
This driver provides support for Nuvoton NPCM750/730/715/705 PWM
and Fan controllers.
This driver can also be built as a module. If so, the module
will be called npcm750-pwm-fan.
config SENSORS_NSA320
tristate "ZyXEL NSA320 and compatible fan speed and temperature sensors"
depends on GPIOLIB && OF
depends on MACH_KIRKWOOD || COMPILE_TEST
help
If you say yes here you get support for hardware monitoring
for the ZyXEL NSA320 Media Server and other compatible devices
(probably the NSA325 and some NSA310 variants).
The sensor data is taken from a Holtek HT46R065 microcontroller
connected to GPIO lines.
This driver can also be built as a module. If so, the module
will be called nsa320-hwmon.
source "drivers/hwmon/occ/Kconfig"
config SENSORS_PCF8591
tristate "Philips PCF8591 ADC/DAC"
depends on I2C
help
If you say yes here you get support for Philips PCF8591 4-channel
ADC, 1-channel DAC chips.
This driver can also be built as a module. If so, the module
will be called pcf8591.
These devices are hard to detect and rarely found on mainstream
hardware. If unsure, say N.
source "drivers/hwmon/pmbus/Kconfig"
config SENSORS_PWM_FAN
tristate "PWM fan"
depends on (PWM && OF) || COMPILE_TEST
depends on THERMAL || THERMAL=n
help
If you say yes here you get support for fans connected to PWM lines.
The driver uses the generic PWM interface, thus it will work on a
variety of SoCs.
This driver can also be built as a module. If so, the module
will be called pwm-fan.
config SENSORS_RASPBERRYPI_HWMON
tristate "Raspberry Pi voltage monitor"
depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
help
If you say yes here you get support for voltage sensor on the
Raspberry Pi.
This driver can also be built as a module. If so, the module
will be called raspberrypi-hwmon.
config SENSORS_SHT15
tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
depends on GPIOLIB || COMPILE_TEST
select BITREVERSE
help
If you say yes here you get support for the Sensiron SHT10, SHT11,
SHT15, SHT71, SHT75 humidity and temperature sensors.
This driver can also be built as a module. If so, the module
will be called sht15.
config SENSORS_SHT21
tristate "Sensiron humidity and temperature sensors. SHT21 and compat."
depends on I2C
help
If you say yes here you get support for the Sensiron SHT21, SHT25
humidity and temperature sensors.
This driver can also be built as a module. If so, the module
will be called sht21.
config SENSORS_SHT3x
tristate "Sensiron humidity and temperature sensors. SHT3x and compat."
depends on I2C
select CRC8
help
If you say yes here you get support for the Sensiron SHT30 and SHT31
humidity and temperature sensors.
This driver can also be built as a module. If so, the module
will be called sht3x.
config SENSORS_SHTC1
tristate "Sensiron humidity and temperature sensors. SHTC1 and compat."
depends on I2C
help
If you say yes here you get support for the Sensiron SHTC1, SHTW1,
and SHTC3 humidity and temperature sensors.
This driver can also be built as a module. If so, the module
will be called shtc1.
config SENSORS_S3C
tristate "Samsung built-in ADC"
depends on S3C_ADC
help
If you say yes here you get support for the on-board ADCs of
the Samsung S3C24XX, S3C64XX and other series of SoC
This driver can also be built as a module. If so, the module
will be called s3c-hwmon.
config SENSORS_S3C_RAW
bool "Include raw channel attributes in sysfs"
depends on SENSORS_S3C
help
Say Y here if you want to include raw copies of all the ADC
channels in sysfs.
config SENSORS_SIS5595
tristate "Silicon Integrated Systems Corp. SiS5595"
depends on PCI
help
If you say yes here you get support for the integrated sensors in
SiS5595 South Bridges.
This driver can also be built as a module. If so, the module
will be called sis5595.
config SENSORS_DME1737
tristate "SMSC DME1737, SCH311x and compatibles"
depends on I2C && !PPC
select HWMON_VID
help
If you say yes here you get support for the hardware monitoring
and fan control features of the SMSC DME1737, SCH311x, SCH5027, and
Asus A8000 Super-I/O chips.
This driver can also be built as a module. If so, the module
will be called dme1737.
config SENSORS_EMC1403
tristate "SMSC EMC1403/23 thermal sensor"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for the SMSC EMC1403/23
temperature monitoring chip.
Threshold values can be configured using sysfs.
Data from the different diodes are accessible via sysfs.
config SENSORS_EMC2103
tristate "SMSC EMC2103"
depends on I2C
help
If you say yes here you get support for the temperature
and fan sensors of the SMSC EMC2103 chips.
This driver can also be built as a module. If so, the module
will be called emc2103.
config SENSORS_EMC6W201
tristate "SMSC EMC6W201"
depends on I2C
help
If you say yes here you get support for the SMSC EMC6W201
hardware monitoring chip.
This driver can also be built as a module. If so, the module
will be called emc6w201.
config SENSORS_SMSC47M1
tristate "SMSC LPC47M10x and compatibles"
depends on !PPC
help
If you say yes here you get support for the integrated fan
monitoring and control capabilities of the SMSC LPC47B27x,
LPC47M10x, LPC47M112, LPC47M13x, LPC47M14x, LPC47M15x,
LPC47M192, LPC47M292 and LPC47M997 chips.
The temperature and voltage sensor features of the LPC47M15x,
LPC47M192, LPC47M292 and LPC47M997 are supported by another
driver, select also "SMSC LPC47M192 and compatibles" below for
those.
This driver can also be built as a module. If so, the module
will be called smsc47m1.
config SENSORS_SMSC47M192
tristate "SMSC LPC47M192 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the temperature and
voltage sensors of the SMSC LPC47M192, LPC47M15x, LPC47M292
and LPC47M997 chips.
The fan monitoring and control capabilities of these chips
are supported by another driver, select
"SMSC LPC47M10x and compatibles" above. You need both drivers
if you want fan control and voltage/temperature sensor support.
This driver can also be built as a module. If so, the module
will be called smsc47m192.
config SENSORS_SMSC47B397
tristate "SMSC LPC47B397-NC"
depends on !PPC
help
If you say yes here you get support for the SMSC LPC47B397-NC
sensor chip.
This driver can also be built as a module. If so, the module
will be called smsc47b397.
config SENSORS_SCH56XX_COMMON
tristate
config SENSORS_SCH5627
tristate "SMSC SCH5627"
depends on !PPC && WATCHDOG
select SENSORS_SCH56XX_COMMON
select WATCHDOG_CORE
help
If you say yes here you get support for the hardware monitoring
features of the SMSC SCH5627 Super-I/O chip including support for
the integrated watchdog.
This driver can also be built as a module. If so, the module
will be called sch5627.
config SENSORS_SCH5636
tristate "SMSC SCH5636"
depends on !PPC && WATCHDOG
select SENSORS_SCH56XX_COMMON
select WATCHDOG_CORE
help
SMSC SCH5636 Super I/O chips include an embedded microcontroller for
hardware monitoring solutions, allowing motherboard manufacturers to
create their own custom hwmon solution based upon the SCH5636.
Currently this driver only supports the Fujitsu Theseus SCH5636 based
hwmon solution. Say yes here if you want support for the Fujitsu
Theseus' hardware monitoring features including support for the
integrated watchdog.
This driver can also be built as a module. If so, the module
will be called sch5636.
config SENSORS_STTS751
tristate "ST Microelectronics STTS751"
depends on I2C
help
If you say yes here you get support for STTS751
temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called stts751.
config SENSORS_SMM665
tristate "Summit Microelectronics SMM665"
depends on I2C
help
If you say yes here you get support for the hardware monitoring
features of the Summit Microelectronics SMM665/SMM665B Six-Channel
Active DC Output Controller / Monitor.
Other supported chips are SMM465, SMM665C, SMM764, and SMM766.
Support for those chips is untested.
This driver can also be built as a module. If so, the module will
be called smm665.
config SENSORS_ADC128D818
tristate "Texas Instruments ADC128D818"
depends on I2C
help
If you say yes here you get support for the Texas Instruments
ADC128D818 System Monitor with Temperature Sensor chip.
This driver can also be built as a module. If so, the module
will be called adc128d818.
config SENSORS_ADS7828
tristate "Texas Instruments ADS7828 and compatibles"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for Texas Instruments ADS7828 and
ADS7830 8-channel A/D converters. ADS7828 resolution is 12-bit, while
it is 8-bit on ADS7830.
This driver can also be built as a module. If so, the module
will be called ads7828.
config SENSORS_ADS7871
tristate "Texas Instruments ADS7871 A/D converter"
depends on SPI
help
If you say yes here you get support for TI ADS7871 & ADS7870
This driver can also be built as a module. If so, the module
will be called ads7871.
config SENSORS_AMC6821
tristate "Texas Instruments AMC6821"
depends on I2C
help
If you say yes here you get support for the Texas Instruments
AMC6821 hardware monitoring chips.
This driver can also be built as a module. If so, the module
will be called amc6821.
config SENSORS_INA209
tristate "TI / Burr Brown INA209"
depends on I2C
help
If you say yes here you get support for the TI / Burr Brown INA209
voltage / current / power monitor I2C interface.
This driver can also be built as a module. If so, the module will
be called ina209.
config SENSORS_INA2XX
tristate "Texas Instruments INA219 and compatibles"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for INA219, INA220, INA226,
INA230, and INA231 power monitor chips.
The INA2xx driver is configured for the default configuration of
the part as described in the datasheet.
Default value for Rshunt is 10 mOhms.
This driver can also be built as a module. If so, the module
will be called ina2xx.
config SENSORS_INA3221
tristate "Texas Instruments INA3221 Triple Power Monitor"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for the TI INA3221 Triple Power
Monitor.
This driver can also be built as a module. If so, the module
will be called ina3221.
config SENSORS_TC74
tristate "Microchip TC74"
depends on I2C
help
If you say yes here you get support for Microchip TC74 single
input temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called tc74.
config SENSORS_THMC50
tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
depends on I2C
help
If you say yes here you get support for Texas Instruments THMC50
sensor chips and clones: the Analog Devices ADM1022.
This driver can also be built as a module. If so, the module
will be called thmc50.
config SENSORS_TMP102
tristate "Texas Instruments TMP102"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for Texas Instruments TMP102
sensor chips.
This driver can also be built as a module. If so, the module
will be called tmp102.
config SENSORS_TMP103
tristate "Texas Instruments TMP103"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for Texas Instruments TMP103
sensor chips.
This driver can also be built as a module. If so, the module
will be called tmp103.
config SENSORS_TMP108
tristate "Texas Instruments TMP108"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for Texas Instruments TMP108
sensor chips.
This driver can also be built as a module. If so, the module
will be called tmp108.
config SENSORS_TMP401
tristate "Texas Instruments TMP401 and compatibles"
depends on I2C
help
If you say yes here you get support for Texas Instruments TMP401,
TMP411, TMP431, TMP432, TMP435, and TMP461 temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called tmp401.
config SENSORS_TMP421
tristate "Texas Instruments TMP421 and compatible"
depends on I2C
help
If you say yes here you get support for Texas Instruments TMP421,
TMP422, TMP423, TMP441, and TMP442 temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called tmp421.
config SENSORS_TMP513
tristate "Texas Instruments TMP513 and compatibles"
depends on I2C
help
If you say yes here you get support for Texas Instruments TMP512,
and TMP513 temperature and power supply sensor chips.
This driver can also be built as a module. If so, the module
will be called tmp513.
config SENSORS_VEXPRESS
tristate "Versatile Express"
depends on VEXPRESS_CONFIG
help
This driver provides support for hardware sensors available on
the ARM Ltd's Versatile Express platform. It can provide wide
range of information like temperature, power, energy.
config SENSORS_VIA_CPUTEMP
tristate "VIA CPU temperature sensor"
depends on X86
select HWMON_VID
help
If you say yes here you get support for the temperature
sensor inside your CPU. Supported are all known variants of
the VIA C7 and Nano.
config SENSORS_VIA686A
tristate "VIA686A"
depends on PCI
help
If you say yes here you get support for the integrated sensors in
Via 686A/B South Bridges.
This driver can also be built as a module. If so, the module
will be called via686a.
config SENSORS_VT1211
tristate "VIA VT1211"
depends on !PPC
select HWMON_VID
help
If you say yes here then you get support for hardware monitoring
features of the VIA VT1211 Super-I/O chip.
This driver can also be built as a module. If so, the module
will be called vt1211.
config SENSORS_VT8231
tristate "VIA VT8231"
depends on PCI
select HWMON_VID
help
If you say yes here then you get support for the integrated sensors
in the VIA VT8231 device.
This driver can also be built as a module. If so, the module
will be called vt8231.
config SENSORS_W83773G
tristate "Nuvoton W83773G"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for the Nuvoton W83773G hardware
monitoring chip.
This driver can also be built as a module. If so, the module
will be called w83773g.
config SENSORS_W83781D
tristate "Winbond W83781D, W83782D, W83783S, Asus AS99127F"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Winbond W8378x series
of sensor chips: the W83781D, W83782D and W83783S, and the similar
Asus AS99127F.
This driver can also be built as a module. If so, the module
will be called w83781d.
config SENSORS_W83791D
tristate "Winbond W83791D"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Winbond W83791D chip.
This driver can also be built as a module. If so, the module
will be called w83791d.
config SENSORS_W83792D
tristate "Winbond W83792D"
depends on I2C
help
If you say yes here you get support for the Winbond W83792D chip.
This driver can also be built as a module. If so, the module
will be called w83792d.
config SENSORS_W83793
tristate "Winbond W83793"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Winbond W83793
hardware monitoring chip, including support for the integrated
watchdog.
This driver can also be built as a module. If so, the module
will be called w83793.
config SENSORS_W83795
tristate "Winbond/Nuvoton W83795G/ADG"
depends on I2C
help
If you say yes here you get support for the Winbond W83795G and
W83795ADG hardware monitoring chip, including manual fan speed
control.
This driver can also be built as a module. If so, the module
will be called w83795.
config SENSORS_W83795_FANCTRL
bool "Include automatic fan control support"
depends on SENSORS_W83795
help
If you say yes here, support for automatic fan speed control
will be included in the driver.
Please also note that this option will create sysfs attribute
files which may change in the future, so you shouldn't rely
on them being stable.
config SENSORS_W83L785TS
tristate "Winbond W83L785TS-S"
depends on I2C
help
If you say yes here you get support for the Winbond W83L785TS-S
sensor chip, which is used on the Asus A7N8X, among other
motherboards.
This driver can also be built as a module. If so, the module
will be called w83l785ts.
config SENSORS_W83L786NG
tristate "Winbond W83L786NG, W83L786NR"
depends on I2C
help
If you say yes here you get support for the Winbond W83L786NG
and W83L786NR sensor chips.
This driver can also be built as a module. If so, the module
will be called w83l786ng.
config SENSORS_W83627HF
tristate "Winbond W83627HF, W83627THF, W83637HF, W83687THF, W83697HF"
depends on !PPC
select HWMON_VID
help
If you say yes here you get support for the Winbond W836X7 series
of sensor chips: the W83627HF, W83627THF, W83637HF, W83687THF and
W83697HF.
This driver can also be built as a module. If so, the module
will be called w83627hf.
config SENSORS_W83627EHF
tristate "Winbond W83627EHF/EHG/DHG/UHG, W83667HG"
depends on !PPC
select HWMON_VID
help
If you say yes here you get support for the hardware
monitoring functionality of the Winbond W83627EHF Super-I/O chip.
This driver also supports the W83627EHG, which is the lead-free
version of the W83627EHF, and the W83627DHG, which is a similar
chip suited for specific Intel processors that use PECI such as
the Core 2 Duo. And also the W83627UHG, which is a stripped down
version of the W83627DHG (as far as hardware monitoring goes.)
This driver also supports Nuvoton W83667HG and W83667HG-B.
This driver can also be built as a module. If so, the module
will be called w83627ehf.
config SENSORS_WM831X
tristate "WM831x PMICs"
depends on MFD_WM831X
help
If you say yes here you get support for the hardware
monitoring functionality of the Wolfson Microelectronics
WM831x series of PMICs.
This driver can also be built as a module. If so, the module
will be called wm831x-hwmon.
config SENSORS_WM8350
tristate "Wolfson Microelectronics WM835x"
depends on MFD_WM8350
help
If you say yes here you get support for the hardware
monitoring features of the WM835x series of PMICs.
This driver can also be built as a module. If so, the module
will be called wm8350-hwmon.
config SENSORS_ULTRA45
tristate "Sun Ultra45 PIC16F747"
depends on SPARC64
help
This driver provides support for the Ultra45 workstation environmental
sensors.
config SENSORS_XGENE
tristate "APM X-Gene SoC hardware monitoring driver"
depends on XGENE_SLIMPRO_MBOX || PCC
help
If you say yes here you get support for the temperature
and power sensors for APM X-Gene SoC.
if ACPI
comment "ACPI drivers"
config SENSORS_ACPI_POWER
tristate "ACPI 4.0 power meter"
help
This driver exposes ACPI 4.0 power meters as hardware monitoring
devices. Say Y (or M) if you have a computer with ACPI 4.0 firmware
and a power meter.
To compile this driver as a module, choose M here:
the module will be called acpi_power_meter.
config SENSORS_ATK0110
tristate "ASUS ATK0110"
depends on X86
help
If you say yes here you get support for the ACPI hardware
monitoring interface found in many ASUS motherboards. This
driver will provide readings of fans, voltages and temperatures
through the system firmware.
This driver can also be built as a module. If so, the module
will be called asus_atk0110.
endif # ACPI
endif # HWMON
Reference in New Issue View Git Blame Copy Permalink