mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-25 20:30:57 +07:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
1071 lines
24 KiB
Plaintext
1071 lines
24 KiB
Plaintext
Summary of HDIO_ ioctl calls.
|
|
============================
|
|
|
|
Edward A. Falk <efalk@google.com>
|
|
|
|
November, 2004
|
|
|
|
This document attempts to describe the ioctl(2) calls supported by
|
|
the HD/IDE layer. These are by-and-large implemented (as of Linux 2.6)
|
|
in drivers/ide/ide.c and drivers/block/scsi_ioctl.c
|
|
|
|
ioctl values are listed in <linux/hdreg.h>. As of this writing, they
|
|
are as follows:
|
|
|
|
ioctls that pass argument pointers to user space:
|
|
|
|
HDIO_GETGEO get device geometry
|
|
HDIO_GET_UNMASKINTR get current unmask setting
|
|
HDIO_GET_MULTCOUNT get current IDE blockmode setting
|
|
HDIO_GET_QDMA get use-qdma flag
|
|
HDIO_SET_XFER set transfer rate via proc
|
|
HDIO_OBSOLETE_IDENTITY OBSOLETE, DO NOT USE
|
|
HDIO_GET_KEEPSETTINGS get keep-settings-on-reset flag
|
|
HDIO_GET_32BIT get current io_32bit setting
|
|
HDIO_GET_NOWERR get ignore-write-error flag
|
|
HDIO_GET_DMA get use-dma flag
|
|
HDIO_GET_NICE get nice flags
|
|
HDIO_GET_IDENTITY get IDE identification info
|
|
HDIO_GET_WCACHE get write cache mode on|off
|
|
HDIO_GET_ACOUSTIC get acoustic value
|
|
HDIO_GET_ADDRESS get sector addressing mode
|
|
HDIO_GET_BUSSTATE get the bus state of the hwif
|
|
HDIO_TRISTATE_HWIF execute a channel tristate
|
|
HDIO_DRIVE_RESET execute a device reset
|
|
HDIO_DRIVE_TASKFILE execute raw taskfile
|
|
HDIO_DRIVE_TASK execute task and special drive command
|
|
HDIO_DRIVE_CMD execute a special drive command
|
|
HDIO_DRIVE_CMD_AEB HDIO_DRIVE_TASK
|
|
|
|
ioctls that pass non-pointer values:
|
|
|
|
HDIO_SET_MULTCOUNT change IDE blockmode
|
|
HDIO_SET_UNMASKINTR permit other irqs during I/O
|
|
HDIO_SET_KEEPSETTINGS keep ioctl settings on reset
|
|
HDIO_SET_32BIT change io_32bit flags
|
|
HDIO_SET_NOWERR change ignore-write-error flag
|
|
HDIO_SET_DMA change use-dma flag
|
|
HDIO_SET_PIO_MODE reconfig interface to new speed
|
|
HDIO_SCAN_HWIF register and (re)scan interface
|
|
HDIO_SET_NICE set nice flags
|
|
HDIO_UNREGISTER_HWIF unregister interface
|
|
HDIO_SET_WCACHE change write cache enable-disable
|
|
HDIO_SET_ACOUSTIC change acoustic behavior
|
|
HDIO_SET_BUSSTATE set the bus state of the hwif
|
|
HDIO_SET_QDMA change use-qdma flag
|
|
HDIO_SET_ADDRESS change lba addressing modes
|
|
|
|
HDIO_SET_IDE_SCSI Set scsi emulation mode on/off
|
|
HDIO_SET_SCSI_IDE not implemented yet
|
|
|
|
|
|
The information that follows was determined from reading kernel source
|
|
code. It is likely that some corrections will be made over time.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
General:
|
|
|
|
Unless otherwise specified, all ioctl calls return 0 on success
|
|
and -1 with errno set to an appropriate value on error.
|
|
|
|
Unless otherwise specified, all ioctl calls return -1 and set
|
|
errno to EFAULT on a failed attempt to copy data to or from user
|
|
address space.
|
|
|
|
Unless otherwise specified, all data structures and constants
|
|
are defined in <linux/hdreg.h>
|
|
|
|
|
|
|
|
HDIO_GETGEO get device geometry
|
|
|
|
usage:
|
|
|
|
struct hd_geometry geom;
|
|
ioctl(fd, HDIO_GETGEO, &geom);
|
|
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
|
|
hd_geometry structure containing:
|
|
|
|
heads number of heads
|
|
sectors number of sectors/track
|
|
cylinders number of cylinders, mod 65536
|
|
start starting sector of this partition.
|
|
|
|
|
|
error returns:
|
|
EINVAL if the device is not a disk drive or floppy drive,
|
|
or if the user passes a null pointer
|
|
|
|
|
|
notes:
|
|
|
|
Not particularly useful with modern disk drives, whose geometry
|
|
is a polite fiction anyway. Modern drives are addressed
|
|
purely by sector number nowadays (lba addressing), and the
|
|
drive geometry is an abstraction which is actually subject
|
|
to change. Currently (as of Nov 2004), the geometry values
|
|
are the "bios" values -- presumably the values the drive had
|
|
when Linux first booted.
|
|
|
|
In addition, the cylinders field of the hd_geometry is an
|
|
unsigned short, meaning that on most architectures, this
|
|
ioctl will not return a meaningful value on drives with more
|
|
than 65535 tracks.
|
|
|
|
The start field is unsigned long, meaning that it will not
|
|
contain a meaningful value for disks over 219 Gb in size.
|
|
|
|
|
|
|
|
|
|
HDIO_GET_UNMASKINTR get current unmask setting
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_UNMASKINTR, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the drive's current unmask setting
|
|
|
|
|
|
|
|
HDIO_SET_UNMASKINTR permit other irqs during I/O
|
|
|
|
usage:
|
|
|
|
unsigned long val;
|
|
ioctl(fd, HDIO_SET_UNMASKINTR, val);
|
|
|
|
inputs:
|
|
New value for unmask flag
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 1]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
|
|
HDIO_GET_MULTCOUNT get current IDE blockmode setting
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_MULTCOUNT, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the current IDE block mode setting. This
|
|
controls how many sectors the drive will transfer per
|
|
interrupt.
|
|
|
|
|
|
|
|
HDIO_SET_MULTCOUNT change IDE blockmode
|
|
|
|
usage:
|
|
|
|
int val;
|
|
ioctl(fd, HDIO_SET_MULTCOUNT, val);
|
|
|
|
inputs:
|
|
New value for IDE block mode setting. This controls how many
|
|
sectors the drive will transfer per interrupt.
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range supported by disk.
|
|
EBUSY Controller busy or blockmode already set.
|
|
EIO Drive did not accept new block mode.
|
|
|
|
notes:
|
|
|
|
Source code comments read:
|
|
|
|
This is tightly woven into the driver->do_special can not
|
|
touch. DON'T do it again until a total personality rewrite
|
|
is committed.
|
|
|
|
If blockmode has already been set, this ioctl will fail with
|
|
EBUSY
|
|
|
|
|
|
|
|
HDIO_GET_QDMA get use-qdma flag
|
|
|
|
Not implemented, as of 2.6.8.1
|
|
|
|
|
|
|
|
HDIO_SET_XFER set transfer rate via proc
|
|
|
|
Not implemented, as of 2.6.8.1
|
|
|
|
|
|
|
|
HDIO_OBSOLETE_IDENTITY OBSOLETE, DO NOT USE
|
|
|
|
Same as HDIO_GET_IDENTITY (see below), except that it only
|
|
returns the first 142 bytes of drive identity information.
|
|
|
|
|
|
|
|
HDIO_GET_IDENTITY get IDE identification info
|
|
|
|
usage:
|
|
|
|
unsigned char identity[512];
|
|
ioctl(fd, HDIO_GET_IDENTITY, identity);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
|
|
ATA drive identity information. For full description, see
|
|
the IDENTIFY DEVICE and IDENTIFY PACKET DEVICE commands in
|
|
the ATA specification.
|
|
|
|
error returns:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
ENOMSG IDENTIFY DEVICE information not available
|
|
|
|
notes:
|
|
|
|
Returns information that was obtained when the drive was
|
|
probed. Some of this information is subject to change, and
|
|
this ioctl does not re-probe the drive to update the
|
|
information.
|
|
|
|
This information is also available from /proc/ide/hdX/identify
|
|
|
|
|
|
|
|
HDIO_GET_KEEPSETTINGS get keep-settings-on-reset flag
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_KEEPSETTINGS, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the current "keep settings" flag
|
|
|
|
notes:
|
|
|
|
When set, indicates that kernel should restore settings
|
|
after a drive reset.
|
|
|
|
|
|
|
|
HDIO_SET_KEEPSETTINGS keep ioctl settings on reset
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_SET_KEEPSETTINGS, val);
|
|
|
|
inputs:
|
|
New value for keep_settings flag
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 1]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
HDIO_GET_32BIT get current io_32bit setting
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_32BIT, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the current io_32bit setting
|
|
|
|
notes:
|
|
|
|
0=16-bit, 1=32-bit, 2,3 = 32bit+sync
|
|
|
|
|
|
|
|
HDIO_GET_NOWERR get ignore-write-error flag
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_NOWERR, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the current ignore-write-error flag
|
|
|
|
|
|
|
|
HDIO_GET_DMA get use-dma flag
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_DMA, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the current use-dma flag
|
|
|
|
|
|
|
|
HDIO_GET_NICE get nice flags
|
|
|
|
usage:
|
|
|
|
long nice;
|
|
ioctl(fd, HDIO_GET_NICE, &nice);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
|
|
The drive's "nice" values.
|
|
|
|
notes:
|
|
|
|
Per-drive flags which determine when the system will give more
|
|
bandwidth to other devices sharing the same IDE bus.
|
|
See <linux/hdreg.h>, near symbol IDE_NICE_DSC_OVERLAP.
|
|
|
|
|
|
|
|
|
|
HDIO_SET_NICE set nice flags
|
|
|
|
usage:
|
|
|
|
unsigned long nice;
|
|
...
|
|
ioctl(fd, HDIO_SET_NICE, nice);
|
|
|
|
inputs:
|
|
bitmask of nice flags.
|
|
|
|
outputs: none
|
|
|
|
error returns:
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EPERM Flags other than DSC_OVERLAP and NICE_1 set.
|
|
EPERM DSC_OVERLAP specified but not supported by drive
|
|
|
|
notes:
|
|
|
|
This ioctl sets the DSC_OVERLAP and NICE_1 flags from values
|
|
provided by the user.
|
|
|
|
Nice flags are listed in <linux/hdreg.h>, starting with
|
|
IDE_NICE_DSC_OVERLAP. These values represent shifts.
|
|
|
|
|
|
|
|
|
|
|
|
HDIO_GET_WCACHE get write cache mode on|off
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_WCACHE, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the current write cache mode
|
|
|
|
|
|
|
|
HDIO_GET_ACOUSTIC get acoustic value
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_ACOUSTIC, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the current acoustic settings
|
|
|
|
notes:
|
|
|
|
See HDIO_SET_ACOUSTIC
|
|
|
|
|
|
|
|
HDIO_GET_ADDRESS
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_GET_ADDRESS, &val);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
The value of the current addressing mode:
|
|
0 = 28-bit
|
|
1 = 48-bit
|
|
2 = 48-bit doing 28-bit
|
|
3 = 64-bit
|
|
|
|
|
|
|
|
HDIO_GET_BUSSTATE get the bus state of the hwif
|
|
|
|
usage:
|
|
|
|
long state;
|
|
ioctl(fd, HDIO_SCAN_HWIF, &state);
|
|
|
|
inputs: none
|
|
|
|
outputs:
|
|
Current power state of the IDE bus. One of BUSSTATE_OFF,
|
|
BUSSTATE_ON, or BUSSTATE_TRISTATE
|
|
|
|
error returns:
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
|
|
|
|
|
|
|
|
HDIO_SET_BUSSTATE set the bus state of the hwif
|
|
|
|
usage:
|
|
|
|
int state;
|
|
...
|
|
ioctl(fd, HDIO_SCAN_HWIF, state);
|
|
|
|
inputs:
|
|
Desired IDE power state. One of BUSSTATE_OFF, BUSSTATE_ON,
|
|
or BUSSTATE_TRISTATE
|
|
|
|
outputs: none
|
|
|
|
error returns:
|
|
EACCES Access denied: requires CAP_SYS_RAWIO
|
|
EOPNOTSUPP Hardware interface does not support bus power control
|
|
|
|
|
|
|
|
|
|
HDIO_TRISTATE_HWIF execute a channel tristate
|
|
|
|
Not implemented, as of 2.6.8.1. See HDIO_SET_BUSSTATE
|
|
|
|
|
|
|
|
HDIO_DRIVE_RESET execute a device reset
|
|
|
|
usage:
|
|
|
|
int args[3]
|
|
...
|
|
ioctl(fd, HDIO_DRIVE_RESET, args);
|
|
|
|
inputs: none
|
|
|
|
outputs: none
|
|
|
|
error returns:
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
|
|
notes:
|
|
|
|
Abort any current command, prevent anything else from being
|
|
queued, execute a reset on the device, and issue BLKRRPART
|
|
ioctl on the block device.
|
|
|
|
Executes an ATAPI soft reset if applicable, otherwise
|
|
executes an ATA soft reset on the controller.
|
|
|
|
|
|
|
|
HDIO_DRIVE_TASKFILE execute raw taskfile
|
|
|
|
Note: If you don't have a copy of the ANSI ATA specification
|
|
handy, you should probably ignore this ioctl.
|
|
|
|
Execute an ATA disk command directly by writing the "taskfile"
|
|
registers of the drive. Requires ADMIN and RAWIO access
|
|
privileges.
|
|
|
|
usage:
|
|
|
|
struct {
|
|
ide_task_request_t req_task;
|
|
u8 outbuf[OUTPUT_SIZE];
|
|
u8 inbuf[INPUT_SIZE];
|
|
} task;
|
|
memset(&task.req_task, 0, sizeof(task.req_task));
|
|
task.req_task.out_size = sizeof(task.outbuf);
|
|
task.req_task.in_size = sizeof(task.inbuf);
|
|
...
|
|
ioctl(fd, HDIO_DRIVE_TASKFILE, &task);
|
|
...
|
|
|
|
inputs:
|
|
|
|
(See below for details on memory area passed to ioctl.)
|
|
|
|
io_ports[8] values to be written to taskfile registers
|
|
hob_ports[8] high-order bytes, for extended commands.
|
|
out_flags flags indicating which registers are valid
|
|
in_flags flags indicating which registers should be returned
|
|
data_phase see below
|
|
req_cmd command type to be executed
|
|
out_size size of output buffer
|
|
outbuf buffer of data to be transmitted to disk
|
|
inbuf buffer of data to be received from disk (see [1])
|
|
|
|
outputs:
|
|
|
|
io_ports[] values returned in the taskfile registers
|
|
hob_ports[] high-order bytes, for extended commands.
|
|
out_flags flags indicating which registers are valid (see [2])
|
|
in_flags flags indicating which registers should be returned
|
|
outbuf buffer of data to be transmitted to disk (see [1])
|
|
inbuf buffer of data to be received from disk
|
|
|
|
error returns:
|
|
EACCES CAP_SYS_ADMIN or CAP_SYS_RAWIO privilege not set.
|
|
ENOMSG Device is not a disk drive.
|
|
ENOMEM Unable to allocate memory for task
|
|
EFAULT req_cmd == TASKFILE_IN_OUT (not implemented as of 2.6.8)
|
|
EPERM req_cmd == TASKFILE_MULTI_OUT and drive
|
|
multi-count not yet set.
|
|
EIO Drive failed the command.
|
|
|
|
notes:
|
|
|
|
[1] READ THE FOLLOWING NOTES *CAREFULLY*. THIS IOCTL IS
|
|
FULL OF GOTCHAS. Extreme caution should be used with using
|
|
this ioctl. A mistake can easily corrupt data or hang the
|
|
system.
|
|
|
|
[2] Both the input and output buffers are copied from the
|
|
user and written back to the user, even when not used.
|
|
|
|
[3] If one or more bits are set in out_flags and in_flags is
|
|
zero, the following values are used for in_flags.all and
|
|
written back into in_flags on completion.
|
|
|
|
* IDE_TASKFILE_STD_IN_FLAGS | (IDE_HOB_STD_IN_FLAGS << 8)
|
|
if LBA48 addressing is enabled for the drive
|
|
* IDE_TASKFILE_STD_IN_FLAGS
|
|
if CHS/LBA28
|
|
|
|
The association between in_flags.all and each enable
|
|
bitfield flips depending on endianess; fortunately, TASKFILE
|
|
only uses inflags.b.data bit and ignores all other bits.
|
|
The end result is that, on any endian machines, it has no
|
|
effect other than modifying in_flags on completion.
|
|
|
|
[4] The default value of SELECT is (0xa0|DEV_bit|LBA_bit)
|
|
except for four drives per port chipsets. For four drives
|
|
per port chipsets, it's (0xa0|DEV_bit|LBA_bit) for the first
|
|
pair and (0x80|DEV_bit|LBA_bit) for the second pair.
|
|
|
|
[5] The argument to the ioctl is a pointer to a region of
|
|
memory containing a ide_task_request_t structure, followed
|
|
by an optional buffer of data to be transmitted to the
|
|
drive, followed by an optional buffer to receive data from
|
|
the drive.
|
|
|
|
Command is passed to the disk drive via the ide_task_request_t
|
|
structure, which contains these fields:
|
|
|
|
io_ports[8] values for the taskfile registers
|
|
hob_ports[8] high-order bytes, for extended commands
|
|
out_flags flags indicating which entries in the
|
|
io_ports[] and hob_ports[] arrays
|
|
contain valid values. Type ide_reg_valid_t.
|
|
in_flags flags indicating which entries in the
|
|
io_ports[] and hob_ports[] arrays
|
|
are expected to contain valid values
|
|
on return.
|
|
data_phase See below
|
|
req_cmd Command type, see below
|
|
out_size output (user->drive) buffer size, bytes
|
|
in_size input (drive->user) buffer size, bytes
|
|
|
|
When out_flags is zero, the following registers are loaded.
|
|
|
|
HOB_FEATURE If the drive supports LBA48
|
|
HOB_NSECTOR If the drive supports LBA48
|
|
HOB_SECTOR If the drive supports LBA48
|
|
HOB_LCYL If the drive supports LBA48
|
|
HOB_HCYL If the drive supports LBA48
|
|
FEATURE
|
|
NSECTOR
|
|
SECTOR
|
|
LCYL
|
|
HCYL
|
|
SELECT First, masked with 0xE0 if LBA48, 0xEF
|
|
otherwise; then, or'ed with the default
|
|
value of SELECT.
|
|
|
|
If any bit in out_flags is set, the following registers are loaded.
|
|
|
|
HOB_DATA If out_flags.b.data is set. HOB_DATA will
|
|
travel on DD8-DD15 on little endian machines
|
|
and on DD0-DD7 on big endian machines.
|
|
DATA If out_flags.b.data is set. DATA will
|
|
travel on DD0-DD7 on little endian machines
|
|
and on DD8-DD15 on big endian machines.
|
|
HOB_NSECTOR If out_flags.b.nsector_hob is set
|
|
HOB_SECTOR If out_flags.b.sector_hob is set
|
|
HOB_LCYL If out_flags.b.lcyl_hob is set
|
|
HOB_HCYL If out_flags.b.hcyl_hob is set
|
|
FEATURE If out_flags.b.feature is set
|
|
NSECTOR If out_flags.b.nsector is set
|
|
SECTOR If out_flags.b.sector is set
|
|
LCYL If out_flags.b.lcyl is set
|
|
HCYL If out_flags.b.hcyl is set
|
|
SELECT Or'ed with the default value of SELECT and
|
|
loaded regardless of out_flags.b.select.
|
|
|
|
Taskfile registers are read back from the drive into
|
|
{io|hob}_ports[] after the command completes iff one of the
|
|
following conditions is met; otherwise, the original values
|
|
will be written back, unchanged.
|
|
|
|
1. The drive fails the command (EIO).
|
|
2. One or more than one bits are set in out_flags.
|
|
3. The requested data_phase is TASKFILE_NO_DATA.
|
|
|
|
HOB_DATA If in_flags.b.data is set. It will contain
|
|
DD8-DD15 on little endian machines and
|
|
DD0-DD7 on big endian machines.
|
|
DATA If in_flags.b.data is set. It will contain
|
|
DD0-DD7 on little endian machines and
|
|
DD8-DD15 on big endian machines.
|
|
HOB_FEATURE If the drive supports LBA48
|
|
HOB_NSECTOR If the drive supports LBA48
|
|
HOB_SECTOR If the drive supports LBA48
|
|
HOB_LCYL If the drive supports LBA48
|
|
HOB_HCYL If the drive supports LBA48
|
|
NSECTOR
|
|
SECTOR
|
|
LCYL
|
|
HCYL
|
|
|
|
The data_phase field describes the data transfer to be
|
|
performed. Value is one of:
|
|
|
|
TASKFILE_IN
|
|
TASKFILE_MULTI_IN
|
|
TASKFILE_OUT
|
|
TASKFILE_MULTI_OUT
|
|
TASKFILE_IN_OUT
|
|
TASKFILE_IN_DMA
|
|
TASKFILE_IN_DMAQ == IN_DMA (queueing not supported)
|
|
TASKFILE_OUT_DMA
|
|
TASKFILE_OUT_DMAQ == OUT_DMA (queueing not supported)
|
|
TASKFILE_P_IN unimplemented
|
|
TASKFILE_P_IN_DMA unimplemented
|
|
TASKFILE_P_IN_DMAQ unimplemented
|
|
TASKFILE_P_OUT unimplemented
|
|
TASKFILE_P_OUT_DMA unimplemented
|
|
TASKFILE_P_OUT_DMAQ unimplemented
|
|
|
|
The req_cmd field classifies the command type. It may be
|
|
one of:
|
|
|
|
IDE_DRIVE_TASK_NO_DATA
|
|
IDE_DRIVE_TASK_SET_XFER unimplemented
|
|
IDE_DRIVE_TASK_IN
|
|
IDE_DRIVE_TASK_OUT unimplemented
|
|
IDE_DRIVE_TASK_RAW_WRITE
|
|
|
|
[6] Do not access {in|out}_flags->all except for resetting
|
|
all the bits. Always access individual bit fields. ->all
|
|
value will flip depending on endianess. For the same
|
|
reason, do not use IDE_{TASKFILE|HOB}_STD_{OUT|IN}_FLAGS
|
|
constants defined in hdreg.h.
|
|
|
|
|
|
|
|
HDIO_DRIVE_CMD execute a special drive command
|
|
|
|
Note: If you don't have a copy of the ANSI ATA specification
|
|
handy, you should probably ignore this ioctl.
|
|
|
|
usage:
|
|
|
|
u8 args[4+XFER_SIZE];
|
|
...
|
|
ioctl(fd, HDIO_DRIVE_CMD, args);
|
|
|
|
inputs:
|
|
|
|
Commands other than WIN_SMART
|
|
args[0] COMMAND
|
|
args[1] NSECTOR
|
|
args[2] FEATURE
|
|
args[3] NSECTOR
|
|
|
|
WIN_SMART
|
|
args[0] COMMAND
|
|
args[1] SECTOR
|
|
args[2] FEATURE
|
|
args[3] NSECTOR
|
|
|
|
outputs:
|
|
|
|
args[] buffer is filled with register values followed by any
|
|
data returned by the disk.
|
|
args[0] status
|
|
args[1] error
|
|
args[2] NSECTOR
|
|
args[3] undefined
|
|
args[4+] NSECTOR * 512 bytes of data returned by the command.
|
|
|
|
error returns:
|
|
EACCES Access denied: requires CAP_SYS_RAWIO
|
|
ENOMEM Unable to allocate memory for task
|
|
EIO Drive reports error
|
|
|
|
notes:
|
|
|
|
[1] For commands other than WIN_SMART, args[1] should equal
|
|
args[3]. SECTOR, LCYL and HCYL are undefined. For
|
|
WIN_SMART, 0x4f and 0xc2 are loaded into LCYL and HCYL
|
|
respectively. In both cases SELECT will contain the default
|
|
value for the drive. Please refer to HDIO_DRIVE_TASKFILE
|
|
notes for the default value of SELECT.
|
|
|
|
[2] If NSECTOR value is greater than zero and the drive sets
|
|
DRQ when interrupting for the command, NSECTOR * 512 bytes
|
|
are read from the device into the area following NSECTOR.
|
|
In the above example, the area would be
|
|
args[4..4+XFER_SIZE]. 16bit PIO is used regardless of
|
|
HDIO_SET_32BIT setting.
|
|
|
|
[3] If COMMAND == WIN_SETFEATURES && FEATURE == SETFEATURES_XFER
|
|
&& NSECTOR >= XFER_SW_DMA_0 && the drive supports any DMA
|
|
mode, IDE driver will try to tune the transfer mode of the
|
|
drive accordingly.
|
|
|
|
|
|
|
|
HDIO_DRIVE_TASK execute task and special drive command
|
|
|
|
Note: If you don't have a copy of the ANSI ATA specification
|
|
handy, you should probably ignore this ioctl.
|
|
|
|
usage:
|
|
|
|
u8 args[7];
|
|
...
|
|
ioctl(fd, HDIO_DRIVE_TASK, args);
|
|
|
|
inputs:
|
|
|
|
Taskfile register values:
|
|
args[0] COMMAND
|
|
args[1] FEATURE
|
|
args[2] NSECTOR
|
|
args[3] SECTOR
|
|
args[4] LCYL
|
|
args[5] HCYL
|
|
args[6] SELECT
|
|
|
|
outputs:
|
|
|
|
Taskfile register values:
|
|
args[0] status
|
|
args[1] error
|
|
args[2] NSECTOR
|
|
args[3] SECTOR
|
|
args[4] LCYL
|
|
args[5] HCYL
|
|
args[6] SELECT
|
|
|
|
error returns:
|
|
EACCES Access denied: requires CAP_SYS_RAWIO
|
|
ENOMEM Unable to allocate memory for task
|
|
ENOMSG Device is not a disk drive.
|
|
EIO Drive failed the command.
|
|
|
|
notes:
|
|
|
|
[1] DEV bit (0x10) of SELECT register is ignored and the
|
|
appropriate value for the drive is used. All other bits
|
|
are used unaltered.
|
|
|
|
|
|
|
|
HDIO_DRIVE_CMD_AEB HDIO_DRIVE_TASK
|
|
|
|
Not implemented, as of 2.6.8.1
|
|
|
|
|
|
|
|
HDIO_SET_32BIT change io_32bit flags
|
|
|
|
usage:
|
|
|
|
int val;
|
|
ioctl(fd, HDIO_SET_32BIT, val);
|
|
|
|
inputs:
|
|
New value for io_32bit flag
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 3]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
|
|
HDIO_SET_NOWERR change ignore-write-error flag
|
|
|
|
usage:
|
|
|
|
int val;
|
|
ioctl(fd, HDIO_SET_NOWERR, val);
|
|
|
|
inputs:
|
|
New value for ignore-write-error flag. Used for ignoring
|
|
WRERR_STAT
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 1]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
HDIO_SET_DMA change use-dma flag
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_SET_DMA, val);
|
|
|
|
inputs:
|
|
New value for use-dma flag
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 1]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
HDIO_SET_PIO_MODE reconfig interface to new speed
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_SET_PIO_MODE, val);
|
|
|
|
inputs:
|
|
New interface speed.
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 255]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
HDIO_SCAN_HWIF register and (re)scan interface
|
|
|
|
usage:
|
|
|
|
int args[3]
|
|
...
|
|
ioctl(fd, HDIO_SCAN_HWIF, args);
|
|
|
|
inputs:
|
|
args[0] io address to probe
|
|
args[1] control address to probe
|
|
args[2] irq number
|
|
|
|
outputs: none
|
|
|
|
error returns:
|
|
EACCES Access denied: requires CAP_SYS_RAWIO
|
|
EIO Probe failed.
|
|
|
|
notes:
|
|
|
|
This ioctl initializes the addresses and irq for a disk
|
|
controller, probes for drives, and creates /proc/ide
|
|
interfaces as appropiate.
|
|
|
|
|
|
|
|
HDIO_UNREGISTER_HWIF unregister interface
|
|
|
|
usage:
|
|
|
|
int index;
|
|
ioctl(fd, HDIO_UNREGISTER_HWIF, index);
|
|
|
|
inputs:
|
|
index index of hardware interface to unregister
|
|
|
|
outputs: none
|
|
|
|
error returns:
|
|
EACCES Access denied: requires CAP_SYS_RAWIO
|
|
|
|
notes:
|
|
|
|
This ioctl removes a hardware interface from the kernel.
|
|
|
|
Currently (2.6.8) this ioctl silently fails if any drive on
|
|
the interface is busy.
|
|
|
|
|
|
|
|
HDIO_SET_WCACHE change write cache enable-disable
|
|
|
|
usage:
|
|
|
|
int val;
|
|
ioctl(fd, HDIO_SET_WCACHE, val);
|
|
|
|
inputs:
|
|
New value for write cache enable
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 1]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
HDIO_SET_ACOUSTIC change acoustic behavior
|
|
|
|
usage:
|
|
|
|
int val;
|
|
ioctl(fd, HDIO_SET_ACOUSTIC, val);
|
|
|
|
inputs:
|
|
New value for drive acoustic settings
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 254]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
HDIO_SET_QDMA change use-qdma flag
|
|
|
|
Not implemented, as of 2.6.8.1
|
|
|
|
|
|
|
|
HDIO_SET_ADDRESS change lba addressing modes
|
|
|
|
usage:
|
|
|
|
int val;
|
|
ioctl(fd, HDIO_SET_ADDRESS, val);
|
|
|
|
inputs:
|
|
New value for addressing mode
|
|
0 = 28-bit
|
|
1 = 48-bit
|
|
2 = 48-bit doing 28-bit
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 2]
|
|
EBUSY Controller busy
|
|
EIO Drive does not support lba48 mode.
|
|
|
|
|
|
HDIO_SET_IDE_SCSI
|
|
|
|
usage:
|
|
|
|
long val;
|
|
ioctl(fd, HDIO_SET_IDE_SCSI, val);
|
|
|
|
inputs:
|
|
New value for scsi emulation mode (?)
|
|
|
|
outputs: none
|
|
|
|
error return:
|
|
EINVAL (bdev != bdev->bd_contains) (not sure what this means)
|
|
EACCES Access denied: requires CAP_SYS_ADMIN
|
|
EINVAL value out of range [0 1]
|
|
EBUSY Controller busy
|
|
|
|
|
|
|
|
HDIO_SET_SCSI_IDE
|
|
|
|
Not implemented, as of 2.6.8.1
|
|
|
|
|