linux_dsm_epyc7002/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
Martin Blumenstingl 41ed2e0db4 ARM64: dts: meson: enable the saradc node in meson-gx-p23x-q20x.dtsi
meson-gxl-s905d-p230.dts and meson-gxm-q200.dts enable the saradc node
(and configure it's vref-supply "VDDIO_AO18") in their corresponding
.dts file.
Move both (the saradc node as well as the VDDIO_AO18 regulator) to
remove some duplicate code.

As a positive side-effect this enables the saradc also for the P231 (GXL
S905D) and Q201 (GXM S912) development boards which are similar to the
P230/Q200 boards (P231 and Q201 use the internal 100Mbit/s PHY, while
P230 and Q200 have an external RGMII PHY).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-07-20 08:18:11 -07:00

231 lines
4.3 KiB
Plaintext

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*/
/* Common DTSI for same Amlogic Q200/Q201 and P230/P231 boards using either
* the pin-compatible S912 (GXM) or S905D (GXL) SoCs.
*/
/ {
aliases {
serial0 = &uart_AO;
ethernet0 = &ethmac;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
hdmi_5v: regulator-hdmi-5v {
compatible = "regulator-fixed";
regulator-name = "HDMI_5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
};
vddio_ao18: regulator-vddio_ao18 {
compatible = "regulator-fixed";
regulator-name = "VDDIO_AO18";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddio_boot: regulator-vddio_boot {
compatible = "regulator-fixed";
regulator-name = "VDDIO_BOOT";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddao_3v3: regulator-vddao_3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
cvbs-connector {
compatible = "composite-video-connector";
port {
cvbs_connector_in: endpoint {
remote-endpoint = <&cvbs_vdac_out>;
};
};
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&hdmi_tx_tmds_out>;
};
};
};
};
&cec_AO {
status = "okay";
pinctrl-0 = <&ao_cec_pins>;
pinctrl-names = "default";
hdmi-phandle = <&hdmi_tx>;
};
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
};
};
&ethmac {
status = "okay";
};
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
pinctrl-names = "default";
};
&hdmi_tx_tmds_port {
hdmi_tx_tmds_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
pinctrl-names = "default";
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};
&saradc {
status = "okay";
vref-supply = <&vddio_ao18>;
};
/* Wireless SDIO Module */
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
pinctrl-1 = <&sdio_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
non-removable;
disable-wp;
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
pinctrl-1 = <&sdcard_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
disable-wp;
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
cd-inverted;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
pinctrl-1 = <&emmc_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vddio_boot>;
};
/* This UART is brought out to the DB9 connector */
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&usb0 {
status = "okay";
};