mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-13 16:16:42 +07:00
d02f815553
Add register definitions used in several Exar PCI/PCIe UARTs Signed-off-by: Matt Schulte <matts@commtech-fastcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
390 lines
16 KiB
C
390 lines
16 KiB
C
/*
|
|
* include/linux/serial_reg.h
|
|
*
|
|
* Copyright (C) 1992, 1994 by Theodore Ts'o.
|
|
*
|
|
* Redistribution of this file is permitted under the terms of the GNU
|
|
* Public License (GPL)
|
|
*
|
|
* These are the UART port assignments, expressed as offsets from the base
|
|
* register. These assignments should hold for any serial port based on
|
|
* a 8250, 16450, or 16550(A).
|
|
*/
|
|
|
|
#ifndef _LINUX_SERIAL_REG_H
|
|
#define _LINUX_SERIAL_REG_H
|
|
|
|
/*
|
|
* DLAB=0
|
|
*/
|
|
#define UART_RX 0 /* In: Receive buffer */
|
|
#define UART_TX 0 /* Out: Transmit buffer */
|
|
|
|
#define UART_IER 1 /* Out: Interrupt Enable Register */
|
|
#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
|
|
#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
|
|
#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
|
|
#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
|
|
/*
|
|
* Sleep mode for ST16650 and TI16750. For the ST16650, EFR[4]=1
|
|
*/
|
|
#define UART_IERX_SLEEP 0x10 /* Enable sleep mode */
|
|
|
|
#define UART_IIR 2 /* In: Interrupt ID Register */
|
|
#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
|
|
#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
|
|
#define UART_IIR_MSI 0x00 /* Modem status interrupt */
|
|
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
|
|
#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
|
|
#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
|
|
|
|
#define UART_IIR_BUSY 0x07 /* DesignWare APB Busy Detect */
|
|
|
|
#define UART_IIR_RX_TIMEOUT 0x0c /* OMAP RX Timeout interrupt */
|
|
#define UART_IIR_XOFF 0x10 /* OMAP XOFF/Special Character */
|
|
#define UART_IIR_CTS_RTS_DSR 0x20 /* OMAP CTS/RTS/DSR Change */
|
|
|
|
#define UART_FCR 2 /* Out: FIFO Control Register */
|
|
#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
|
|
#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
|
|
#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
|
|
#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
|
|
/*
|
|
* Note: The FIFO trigger levels are chip specific:
|
|
* RX:76 = 00 01 10 11 TX:54 = 00 01 10 11
|
|
* PC16550D: 1 4 8 14 xx xx xx xx
|
|
* TI16C550A: 1 4 8 14 xx xx xx xx
|
|
* TI16C550C: 1 4 8 14 xx xx xx xx
|
|
* ST16C550: 1 4 8 14 xx xx xx xx
|
|
* ST16C650: 8 16 24 28 16 8 24 30 PORT_16650V2
|
|
* NS16C552: 1 4 8 14 xx xx xx xx
|
|
* ST16C654: 8 16 56 60 8 16 32 56 PORT_16654
|
|
* TI16C750: 1 16 32 56 xx xx xx xx PORT_16750
|
|
* TI16C752: 8 16 56 60 8 16 32 56
|
|
* Tegra: 1 4 8 14 16 8 4 1 PORT_TEGRA
|
|
*/
|
|
#define UART_FCR_R_TRIG_00 0x00
|
|
#define UART_FCR_R_TRIG_01 0x40
|
|
#define UART_FCR_R_TRIG_10 0x80
|
|
#define UART_FCR_R_TRIG_11 0xc0
|
|
#define UART_FCR_T_TRIG_00 0x00
|
|
#define UART_FCR_T_TRIG_01 0x10
|
|
#define UART_FCR_T_TRIG_10 0x20
|
|
#define UART_FCR_T_TRIG_11 0x30
|
|
|
|
#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
|
|
#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
|
|
#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
|
|
#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
|
|
#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
|
|
/* 16650 definitions */
|
|
#define UART_FCR6_R_TRIGGER_8 0x00 /* Mask for receive trigger set at 1 */
|
|
#define UART_FCR6_R_TRIGGER_16 0x40 /* Mask for receive trigger set at 4 */
|
|
#define UART_FCR6_R_TRIGGER_24 0x80 /* Mask for receive trigger set at 8 */
|
|
#define UART_FCR6_R_TRIGGER_28 0xC0 /* Mask for receive trigger set at 14 */
|
|
#define UART_FCR6_T_TRIGGER_16 0x00 /* Mask for transmit trigger set at 16 */
|
|
#define UART_FCR6_T_TRIGGER_8 0x10 /* Mask for transmit trigger set at 8 */
|
|
#define UART_FCR6_T_TRIGGER_24 0x20 /* Mask for transmit trigger set at 24 */
|
|
#define UART_FCR6_T_TRIGGER_30 0x30 /* Mask for transmit trigger set at 30 */
|
|
#define UART_FCR7_64BYTE 0x20 /* Go into 64 byte mode (TI16C750) */
|
|
|
|
#define UART_LCR 3 /* Out: Line Control Register */
|
|
/*
|
|
* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
|
|
* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
|
|
*/
|
|
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
|
|
#define UART_LCR_SBC 0x40 /* Set break control */
|
|
#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
|
|
#define UART_LCR_EPAR 0x10 /* Even parity select */
|
|
#define UART_LCR_PARITY 0x08 /* Parity Enable */
|
|
#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 bit, 1=2 bits */
|
|
#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
|
|
#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
|
|
#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
|
|
#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
|
|
|
|
/*
|
|
* Access to some registers depends on register access / configuration
|
|
* mode.
|
|
*/
|
|
#define UART_LCR_CONF_MODE_A UART_LCR_DLAB /* Configutation mode A */
|
|
#define UART_LCR_CONF_MODE_B 0xBF /* Configutation mode B */
|
|
|
|
#define UART_MCR 4 /* Out: Modem Control Register */
|
|
#define UART_MCR_CLKSEL 0x80 /* Divide clock by 4 (TI16C752, EFR[4]=1) */
|
|
#define UART_MCR_TCRTLR 0x40 /* Access TCR/TLR (TI16C752, EFR[4]=1) */
|
|
#define UART_MCR_XONANY 0x20 /* Enable Xon Any (TI16C752, EFR[4]=1) */
|
|
#define UART_MCR_AFE 0x20 /* Enable auto-RTS/CTS (TI16C550C/TI16C750) */
|
|
#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
|
|
#define UART_MCR_OUT2 0x08 /* Out2 complement */
|
|
#define UART_MCR_OUT1 0x04 /* Out1 complement */
|
|
#define UART_MCR_RTS 0x02 /* RTS complement */
|
|
#define UART_MCR_DTR 0x01 /* DTR complement */
|
|
|
|
#define UART_LSR 5 /* In: Line Status Register */
|
|
#define UART_LSR_FIFOE 0x80 /* Fifo error */
|
|
#define UART_LSR_TEMT 0x40 /* Transmitter empty */
|
|
#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
|
|
#define UART_LSR_BI 0x10 /* Break interrupt indicator */
|
|
#define UART_LSR_FE 0x08 /* Frame error indicator */
|
|
#define UART_LSR_PE 0x04 /* Parity error indicator */
|
|
#define UART_LSR_OE 0x02 /* Overrun error indicator */
|
|
#define UART_LSR_DR 0x01 /* Receiver data ready */
|
|
#define UART_LSR_BRK_ERROR_BITS 0x1E /* BI, FE, PE, OE bits */
|
|
|
|
#define UART_MSR 6 /* In: Modem Status Register */
|
|
#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
|
|
#define UART_MSR_RI 0x40 /* Ring Indicator */
|
|
#define UART_MSR_DSR 0x20 /* Data Set Ready */
|
|
#define UART_MSR_CTS 0x10 /* Clear to Send */
|
|
#define UART_MSR_DDCD 0x08 /* Delta DCD */
|
|
#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
|
|
#define UART_MSR_DDSR 0x02 /* Delta DSR */
|
|
#define UART_MSR_DCTS 0x01 /* Delta CTS */
|
|
#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */
|
|
|
|
#define UART_SCR 7 /* I/O: Scratch Register */
|
|
|
|
/*
|
|
* DLAB=1
|
|
*/
|
|
#define UART_DLL 0 /* Out: Divisor Latch Low */
|
|
#define UART_DLM 1 /* Out: Divisor Latch High */
|
|
|
|
/*
|
|
* LCR=0xBF (or DLAB=1 for 16C660)
|
|
*/
|
|
#define UART_EFR 2 /* I/O: Extended Features Register */
|
|
#define UART_XR_EFR 9 /* I/O: Extended Features Register (XR17D15x) */
|
|
#define UART_EFR_CTS 0x80 /* CTS flow control */
|
|
#define UART_EFR_RTS 0x40 /* RTS flow control */
|
|
#define UART_EFR_SCD 0x20 /* Special character detect */
|
|
#define UART_EFR_ECB 0x10 /* Enhanced control bit */
|
|
/*
|
|
* the low four bits control software flow control
|
|
*/
|
|
|
|
/*
|
|
* LCR=0xBF, TI16C752, ST16650, ST16650A, ST16654
|
|
*/
|
|
#define UART_XON1 4 /* I/O: Xon character 1 */
|
|
#define UART_XON2 5 /* I/O: Xon character 2 */
|
|
#define UART_XOFF1 6 /* I/O: Xoff character 1 */
|
|
#define UART_XOFF2 7 /* I/O: Xoff character 2 */
|
|
|
|
/*
|
|
* EFR[4]=1 MCR[6]=1, TI16C752
|
|
*/
|
|
#define UART_TI752_TCR 6 /* I/O: transmission control register */
|
|
#define UART_TI752_TLR 7 /* I/O: trigger level register */
|
|
|
|
/*
|
|
* LCR=0xBF, XR16C85x
|
|
*/
|
|
#define UART_TRG 0 /* FCTR bit 7 selects Rx or Tx
|
|
* In: Fifo count
|
|
* Out: Fifo custom trigger levels */
|
|
/*
|
|
* These are the definitions for the Programmable Trigger Register
|
|
*/
|
|
#define UART_TRG_1 0x01
|
|
#define UART_TRG_4 0x04
|
|
#define UART_TRG_8 0x08
|
|
#define UART_TRG_16 0x10
|
|
#define UART_TRG_32 0x20
|
|
#define UART_TRG_64 0x40
|
|
#define UART_TRG_96 0x60
|
|
#define UART_TRG_120 0x78
|
|
#define UART_TRG_128 0x80
|
|
|
|
#define UART_FCTR 1 /* Feature Control Register */
|
|
#define UART_FCTR_RTS_NODELAY 0x00 /* RTS flow control delay */
|
|
#define UART_FCTR_RTS_4DELAY 0x01
|
|
#define UART_FCTR_RTS_6DELAY 0x02
|
|
#define UART_FCTR_RTS_8DELAY 0x03
|
|
#define UART_FCTR_IRDA 0x04 /* IrDa data encode select */
|
|
#define UART_FCTR_TX_INT 0x08 /* Tx interrupt type select */
|
|
#define UART_FCTR_TRGA 0x00 /* Tx/Rx 550 trigger table select */
|
|
#define UART_FCTR_TRGB 0x10 /* Tx/Rx 650 trigger table select */
|
|
#define UART_FCTR_TRGC 0x20 /* Tx/Rx 654 trigger table select */
|
|
#define UART_FCTR_TRGD 0x30 /* Tx/Rx 850 programmable trigger select */
|
|
#define UART_FCTR_SCR_SWAP 0x40 /* Scratch pad register swap */
|
|
#define UART_FCTR_RX 0x00 /* Programmable trigger mode select */
|
|
#define UART_FCTR_TX 0x80 /* Programmable trigger mode select */
|
|
|
|
/*
|
|
* LCR=0xBF, FCTR[6]=1
|
|
*/
|
|
#define UART_EMSR 7 /* Extended Mode Select Register */
|
|
#define UART_EMSR_FIFO_COUNT 0x01 /* Rx/Tx select */
|
|
#define UART_EMSR_ALT_COUNT 0x02 /* Alternating count select */
|
|
|
|
/*
|
|
* The Intel XScale on-chip UARTs define these bits
|
|
*/
|
|
#define UART_IER_DMAE 0x80 /* DMA Requests Enable */
|
|
#define UART_IER_UUE 0x40 /* UART Unit Enable */
|
|
#define UART_IER_NRZE 0x20 /* NRZ coding Enable */
|
|
#define UART_IER_RTOIE 0x10 /* Receiver Time Out Interrupt Enable */
|
|
|
|
#define UART_IIR_TOD 0x08 /* Character Timeout Indication Detected */
|
|
|
|
#define UART_FCR_PXAR1 0x00 /* receive FIFO threshold = 1 */
|
|
#define UART_FCR_PXAR8 0x40 /* receive FIFO threshold = 8 */
|
|
#define UART_FCR_PXAR16 0x80 /* receive FIFO threshold = 16 */
|
|
#define UART_FCR_PXAR32 0xc0 /* receive FIFO threshold = 32 */
|
|
|
|
/*
|
|
* Intel MID on-chip HSU (High Speed UART) defined bits
|
|
*/
|
|
#define UART_FCR_HSU_64_1B 0x00 /* receive FIFO treshold = 1 */
|
|
#define UART_FCR_HSU_64_16B 0x40 /* receive FIFO treshold = 16 */
|
|
#define UART_FCR_HSU_64_32B 0x80 /* receive FIFO treshold = 32 */
|
|
#define UART_FCR_HSU_64_56B 0xc0 /* receive FIFO treshold = 56 */
|
|
|
|
#define UART_FCR_HSU_16_1B 0x00 /* receive FIFO treshold = 1 */
|
|
#define UART_FCR_HSU_16_4B 0x40 /* receive FIFO treshold = 4 */
|
|
#define UART_FCR_HSU_16_8B 0x80 /* receive FIFO treshold = 8 */
|
|
#define UART_FCR_HSU_16_14B 0xc0 /* receive FIFO treshold = 14 */
|
|
|
|
#define UART_FCR_HSU_64B_FIFO 0x20 /* chose 64 bytes FIFO */
|
|
#define UART_FCR_HSU_16B_FIFO 0x00 /* chose 16 bytes FIFO */
|
|
|
|
#define UART_FCR_HALF_EMPT_TXI 0x00 /* trigger TX_EMPT IRQ for half empty */
|
|
#define UART_FCR_FULL_EMPT_TXI 0x08 /* trigger TX_EMPT IRQ for full empty */
|
|
|
|
/*
|
|
* These register definitions are for the 16C950
|
|
*/
|
|
#define UART_ASR 0x01 /* Additional Status Register */
|
|
#define UART_RFL 0x03 /* Receiver FIFO level */
|
|
#define UART_TFL 0x04 /* Transmitter FIFO level */
|
|
#define UART_ICR 0x05 /* Index Control Register */
|
|
|
|
/* The 16950 ICR registers */
|
|
#define UART_ACR 0x00 /* Additional Control Register */
|
|
#define UART_CPR 0x01 /* Clock Prescalar Register */
|
|
#define UART_TCR 0x02 /* Times Clock Register */
|
|
#define UART_CKS 0x03 /* Clock Select Register */
|
|
#define UART_TTL 0x04 /* Transmitter Interrupt Trigger Level */
|
|
#define UART_RTL 0x05 /* Receiver Interrupt Trigger Level */
|
|
#define UART_FCL 0x06 /* Flow Control Level Lower */
|
|
#define UART_FCH 0x07 /* Flow Control Level Higher */
|
|
#define UART_ID1 0x08 /* ID #1 */
|
|
#define UART_ID2 0x09 /* ID #2 */
|
|
#define UART_ID3 0x0A /* ID #3 */
|
|
#define UART_REV 0x0B /* Revision */
|
|
#define UART_CSR 0x0C /* Channel Software Reset */
|
|
#define UART_NMR 0x0D /* Nine-bit Mode Register */
|
|
#define UART_CTR 0xFF
|
|
|
|
/*
|
|
* The 16C950 Additional Control Register
|
|
*/
|
|
#define UART_ACR_RXDIS 0x01 /* Receiver disable */
|
|
#define UART_ACR_TXDIS 0x02 /* Transmitter disable */
|
|
#define UART_ACR_DSRFC 0x04 /* DSR Flow Control */
|
|
#define UART_ACR_TLENB 0x20 /* 950 trigger levels enable */
|
|
#define UART_ACR_ICRRD 0x40 /* ICR Read enable */
|
|
#define UART_ACR_ASREN 0x80 /* Additional status enable */
|
|
|
|
|
|
|
|
/*
|
|
* These definitions are for the RSA-DV II/S card, from
|
|
*
|
|
* Kiyokazu SUTO <suto@ks-and-ks.ne.jp>
|
|
*/
|
|
|
|
#define UART_RSA_BASE (-8)
|
|
|
|
#define UART_RSA_MSR ((UART_RSA_BASE) + 0) /* I/O: Mode Select Register */
|
|
|
|
#define UART_RSA_MSR_SWAP (1 << 0) /* Swap low/high 8 bytes in I/O port addr */
|
|
#define UART_RSA_MSR_FIFO (1 << 2) /* Enable the external FIFO */
|
|
#define UART_RSA_MSR_FLOW (1 << 3) /* Enable the auto RTS/CTS flow control */
|
|
#define UART_RSA_MSR_ITYP (1 << 4) /* Level (1) / Edge triger (0) */
|
|
|
|
#define UART_RSA_IER ((UART_RSA_BASE) + 1) /* I/O: Interrupt Enable Register */
|
|
|
|
#define UART_RSA_IER_Rx_FIFO_H (1 << 0) /* Enable Rx FIFO half full int. */
|
|
#define UART_RSA_IER_Tx_FIFO_H (1 << 1) /* Enable Tx FIFO half full int. */
|
|
#define UART_RSA_IER_Tx_FIFO_E (1 << 2) /* Enable Tx FIFO empty int. */
|
|
#define UART_RSA_IER_Rx_TOUT (1 << 3) /* Enable char receive timeout int */
|
|
#define UART_RSA_IER_TIMER (1 << 4) /* Enable timer interrupt */
|
|
|
|
#define UART_RSA_SRR ((UART_RSA_BASE) + 2) /* IN: Status Read Register */
|
|
|
|
#define UART_RSA_SRR_Tx_FIFO_NEMP (1 << 0) /* Tx FIFO is not empty (1) */
|
|
#define UART_RSA_SRR_Tx_FIFO_NHFL (1 << 1) /* Tx FIFO is not half full (1) */
|
|
#define UART_RSA_SRR_Tx_FIFO_NFUL (1 << 2) /* Tx FIFO is not full (1) */
|
|
#define UART_RSA_SRR_Rx_FIFO_NEMP (1 << 3) /* Rx FIFO is not empty (1) */
|
|
#define UART_RSA_SRR_Rx_FIFO_NHFL (1 << 4) /* Rx FIFO is not half full (1) */
|
|
#define UART_RSA_SRR_Rx_FIFO_NFUL (1 << 5) /* Rx FIFO is not full (1) */
|
|
#define UART_RSA_SRR_Rx_TOUT (1 << 6) /* Character reception timeout occurred (1) */
|
|
#define UART_RSA_SRR_TIMER (1 << 7) /* Timer interrupt occurred */
|
|
|
|
#define UART_RSA_FRR ((UART_RSA_BASE) + 2) /* OUT: FIFO Reset Register */
|
|
|
|
#define UART_RSA_TIVSR ((UART_RSA_BASE) + 3) /* I/O: Timer Interval Value Set Register */
|
|
|
|
#define UART_RSA_TCR ((UART_RSA_BASE) + 4) /* OUT: Timer Control Register */
|
|
|
|
#define UART_RSA_TCR_SWITCH (1 << 0) /* Timer on */
|
|
|
|
/*
|
|
* The RSA DSV/II board has two fixed clock frequencies. One is the
|
|
* standard rate, and the other is 8 times faster.
|
|
*/
|
|
#define SERIAL_RSA_BAUD_BASE (921600)
|
|
#define SERIAL_RSA_BAUD_BASE_LO (SERIAL_RSA_BAUD_BASE / 8)
|
|
|
|
/*
|
|
* Extra serial register definitions for the internal UARTs
|
|
* in TI OMAP processors.
|
|
*/
|
|
#define UART_OMAP_MDR1 0x08 /* Mode definition register */
|
|
#define UART_OMAP_MDR2 0x09 /* Mode definition register 2 */
|
|
#define UART_OMAP_SCR 0x10 /* Supplementary control register */
|
|
#define UART_OMAP_SSR 0x11 /* Supplementary status register */
|
|
#define UART_OMAP_EBLR 0x12 /* BOF length register */
|
|
#define UART_OMAP_OSC_12M_SEL 0x13 /* OMAP1510 12MHz osc select */
|
|
#define UART_OMAP_MVER 0x14 /* Module version register */
|
|
#define UART_OMAP_SYSC 0x15 /* System configuration register */
|
|
#define UART_OMAP_SYSS 0x16 /* System status register */
|
|
#define UART_OMAP_WER 0x17 /* Wake-up enable register */
|
|
|
|
/*
|
|
* These are the definitions for the MDR1 register
|
|
*/
|
|
#define UART_OMAP_MDR1_16X_MODE 0x00 /* UART 16x mode */
|
|
#define UART_OMAP_MDR1_SIR_MODE 0x01 /* SIR mode */
|
|
#define UART_OMAP_MDR1_16X_ABAUD_MODE 0x02 /* UART 16x auto-baud */
|
|
#define UART_OMAP_MDR1_13X_MODE 0x03 /* UART 13x mode */
|
|
#define UART_OMAP_MDR1_MIR_MODE 0x04 /* MIR mode */
|
|
#define UART_OMAP_MDR1_FIR_MODE 0x05 /* FIR mode */
|
|
#define UART_OMAP_MDR1_CIR_MODE 0x06 /* CIR mode */
|
|
#define UART_OMAP_MDR1_DISABLE 0x07 /* Disable (default state) */
|
|
|
|
/*
|
|
* These are definitions for the Exar XR17V35X and XR17(C|D)15X
|
|
*/
|
|
#define UART_EXAR_8XMODE 0x88 /* 8X sampling rate select */
|
|
#define UART_EXAR_SLEEP 0x8b /* Sleep mode */
|
|
#define UART_EXAR_DVID 0x8d /* Device identification */
|
|
|
|
#define UART_EXAR_FCTR 0x08 /* Feature Control Register */
|
|
#define UART_FCTR_EXAR_IRDA 0x08 /* IrDa data encode select */
|
|
#define UART_FCTR_EXAR_485 0x10 /* Auto 485 half duplex dir ctl */
|
|
#define UART_FCTR_EXAR_TRGA 0x00 /* FIFO trigger table A */
|
|
#define UART_FCTR_EXAR_TRGB 0x60 /* FIFO trigger table B */
|
|
#define UART_FCTR_EXAR_TRGC 0x80 /* FIFO trigger table C */
|
|
#define UART_FCTR_EXAR_TRGD 0xc0 /* FIFO trigger table D programmable */
|
|
|
|
#define UART_EXAR_TXTRG 0x0a /* Tx FIFO trigger level write-only */
|
|
#define UART_EXAR_RXTRG 0x0b /* Rx FIFO trigger level write-only */
|
|
|
|
#endif /* _LINUX_SERIAL_REG_H */
|
|
|