AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-20 01:18:08 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
3587c85667
linux_dsm_epyc7002/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
John Stultz 3587c85667 drm/bridge: adv7511: Re-write the i2c address before EDID probing 
I've found that by just turning the chip on and off via the
POWER_DOWN register, I end up getting i2c_transfer errors on
HiKey.

Investigating further, it turns out that some of the register
state in hardware is getting lost, as the device registers are
reset when the chip is powered down.

Thus this patch simply re-writes the i2c address to the
ADV7511_REG_EDID_I2C_ADDR register to ensure its properly set
before we try to read the EDID data.

Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-7-git-send-email-john.stultz@linaro.org
2017-01-19 09:16:58 +05:30

1228 lines
32 KiB
C
Raw Blame History

/*
* Analog Devices ADV7511 HDMI transmitter driver
*
* Copyright 2012 Analog Devices Inc.
*
* Licensed under the GPL-2.
*/
#include <linux/device.h>
#include <linux/gpio/consumer.h>
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/slab.h>
#include <drm/drmP.h>
#include <drm/drm_atomic.h>
#include <drm/drm_atomic_helper.h>
#include <drm/drm_edid.h>
#include "adv7511.h"
/* ADI recommended values for proper operation. */
static const struct reg_sequence adv7511_fixed_registers[] = {
{ 0x98, 0x03 },
{ 0x9a, 0xe0 },
{ 0x9c, 0x30 },
{ 0x9d, 0x61 },
{ 0xa2, 0xa4 },
{ 0xa3, 0xa4 },
{ 0xe0, 0xd0 },
{ 0xf9, 0x00 },
{ 0x55, 0x02 },
};
/* -----------------------------------------------------------------------------
* Register access
*/
static const uint8_t adv7511_register_defaults[] = {
0x12, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 00 */
0x00, 0x00, 0x01, 0x0e, 0xbc, 0x18, 0x01, 0x13,
0x25, 0x37, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 10 */
0x46, 0x62, 0x04, 0xa8, 0x00, 0x00, 0x1c, 0x84,
0x1c, 0xbf, 0x04, 0xa8, 0x1e, 0x70, 0x02, 0x1e, /* 20 */
0x00, 0x00, 0x04, 0xa8, 0x08, 0x12, 0x1b, 0xac,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 30 */
0x00, 0x00, 0x00, 0x80, 0x00, 0x00, 0x00, 0xb0,
0x00, 0x50, 0x90, 0x7e, 0x79, 0x70, 0x00, 0x00, /* 40 */
0x00, 0xa8, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x02, 0x0d, 0x00, 0x00, 0x00, 0x00, /* 50 */
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 60 */
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x01, 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 70 */
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 80 */
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x00, /* 90 */
0x0b, 0x02, 0x00, 0x18, 0x5a, 0x60, 0x00, 0x00,
0x00, 0x00, 0x80, 0x80, 0x08, 0x04, 0x00, 0x00, /* a0 */
0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x40, 0x14,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* b0 */
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* c0 */
0x00, 0x03, 0x00, 0x00, 0x02, 0x00, 0x01, 0x04,
0x30, 0xff, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, /* d0 */
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x01,
0x80, 0x75, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00, /* e0 */
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x11, 0x00, /* f0 */
0x00, 0x7c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
};
static bool adv7511_register_volatile(struct device *dev, unsigned int reg)
{
switch (reg) {
case ADV7511_REG_CHIP_REVISION:
case ADV7511_REG_SPDIF_FREQ:
case ADV7511_REG_CTS_AUTOMATIC1:
case ADV7511_REG_CTS_AUTOMATIC2:
case ADV7511_REG_VIC_DETECTED:
case ADV7511_REG_VIC_SEND:
case ADV7511_REG_AUX_VIC_DETECTED:
case ADV7511_REG_STATUS:
case ADV7511_REG_GC(1):
case ADV7511_REG_INT(0):
case ADV7511_REG_INT(1):
case ADV7511_REG_PLL_STATUS:
case ADV7511_REG_AN(0):
case ADV7511_REG_AN(1):
case ADV7511_REG_AN(2):
case ADV7511_REG_AN(3):
case ADV7511_REG_AN(4):
case ADV7511_REG_AN(5):
case ADV7511_REG_AN(6):
case ADV7511_REG_AN(7):
case ADV7511_REG_HDCP_STATUS:
case ADV7511_REG_BCAPS:
case ADV7511_REG_BKSV(0):
case ADV7511_REG_BKSV(1):
case ADV7511_REG_BKSV(2):
case ADV7511_REG_BKSV(3):
case ADV7511_REG_BKSV(4):
case ADV7511_REG_DDC_STATUS:
case ADV7511_REG_EDID_READ_CTRL:
case ADV7511_REG_BSTATUS(0):
case ADV7511_REG_BSTATUS(1):
case ADV7511_REG_CHIP_ID_HIGH:
case ADV7511_REG_CHIP_ID_LOW:
return true;
}
return false;
}
static const struct regmap_config adv7511_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = 0xff,
.cache_type = REGCACHE_RBTREE,
.reg_defaults_raw = adv7511_register_defaults,
.num_reg_defaults_raw = ARRAY_SIZE(adv7511_register_defaults),
.volatile_reg = adv7511_register_volatile,
};
/* -----------------------------------------------------------------------------
* Hardware configuration
*/
static void adv7511_set_colormap(struct adv7511 *adv7511, bool enable,
const uint16_t *coeff,
unsigned int scaling_factor)
{
unsigned int i;
regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
ADV7511_CSC_UPDATE_MODE, ADV7511_CSC_UPDATE_MODE);
if (enable) {
for (i = 0; i < 12; ++i) {
regmap_update_bits(adv7511->regmap,
ADV7511_REG_CSC_UPPER(i),
0x1f, coeff[i] >> 8);
regmap_write(adv7511->regmap,
ADV7511_REG_CSC_LOWER(i),
coeff[i] & 0xff);
}
}
if (enable)
regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
0xe0, 0x80 | (scaling_factor << 5));
else
regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
0x80, 0x00);
regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
ADV7511_CSC_UPDATE_MODE, 0);
}
static int adv7511_packet_enable(struct adv7511 *adv7511, unsigned int packet)
{
if (packet & 0xff)
regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
packet, 0xff);
if (packet & 0xff00) {
packet >>= 8;
regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
packet, 0xff);
}
return 0;
}
static int adv7511_packet_disable(struct adv7511 *adv7511, unsigned int packet)
{
if (packet & 0xff)
regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
packet, 0x00);
if (packet & 0xff00) {
packet >>= 8;
regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
packet, 0x00);
}
return 0;
}
/* Coefficients for adv7511 color space conversion */
static const uint16_t adv7511_csc_ycbcr_to_rgb[] = {
0x0734, 0x04ad, 0x0000, 0x1c1b,
0x1ddc, 0x04ad, 0x1f24, 0x0135,
0x0000, 0x04ad, 0x087c, 0x1b77,
};
static void adv7511_set_config_csc(struct adv7511 *adv7511,
struct drm_connector *connector,
bool rgb)
{
struct adv7511_video_config config;
bool output_format_422, output_format_ycbcr;
unsigned int mode;
uint8_t infoframe[17];
if (adv7511->edid)
config.hdmi_mode = drm_detect_hdmi_monitor(adv7511->edid);
else
config.hdmi_mode = false;
hdmi_avi_infoframe_init(&config.avi_infoframe);
config.avi_infoframe.scan_mode = HDMI_SCAN_MODE_UNDERSCAN;
if (rgb) {
config.csc_enable = false;
config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
} else {
config.csc_scaling_factor = ADV7511_CSC_SCALING_4;
config.csc_coefficents = adv7511_csc_ycbcr_to_rgb;
if ((connector->display_info.color_formats &
DRM_COLOR_FORMAT_YCRCB422) &&
config.hdmi_mode) {
config.csc_enable = false;
config.avi_infoframe.colorspace =
HDMI_COLORSPACE_YUV422;
} else {
config.csc_enable = true;
config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
}
}
if (config.hdmi_mode) {
mode = ADV7511_HDMI_CFG_MODE_HDMI;
switch (config.avi_infoframe.colorspace) {
case HDMI_COLORSPACE_YUV444:
output_format_422 = false;
output_format_ycbcr = true;
break;
case HDMI_COLORSPACE_YUV422:
output_format_422 = true;
output_format_ycbcr = true;
break;
default:
output_format_422 = false;
output_format_ycbcr = false;
break;
}
} else {
mode = ADV7511_HDMI_CFG_MODE_DVI;
output_format_422 = false;
output_format_ycbcr = false;
}
adv7511_packet_disable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
adv7511_set_colormap(adv7511, config.csc_enable,
config.csc_coefficents,
config.csc_scaling_factor);
regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x81,
(output_format_422 << 7) | output_format_ycbcr);
regmap_update_bits(adv7511->regmap, ADV7511_REG_HDCP_HDMI_CFG,
ADV7511_HDMI_CFG_MODE_MASK, mode);
hdmi_avi_infoframe_pack(&config.avi_infoframe, infoframe,
sizeof(infoframe));
/* The AVI infoframe id is not configurable */
regmap_bulk_write(adv7511->regmap, ADV7511_REG_AVI_INFOFRAME_VERSION,
infoframe + 1, sizeof(infoframe) - 1);
adv7511_packet_enable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
}
static void adv7511_set_link_config(struct adv7511 *adv7511,
const struct adv7511_link_config *config)
{
/*
* The input style values documented in the datasheet don't match the
* hardware register field values :-(
*/
static const unsigned int input_styles[4] = { 0, 2, 1, 3 };
unsigned int clock_delay;
unsigned int color_depth;
unsigned int input_id;
clock_delay = (config->clock_delay + 1200) / 400;
color_depth = config->input_color_depth == 8 ? 3
: (config->input_color_depth == 10 ? 1 : 2);
/* TODO Support input ID 6 */
if (config->input_colorspace != HDMI_COLORSPACE_YUV422)
input_id = config->input_clock == ADV7511_INPUT_CLOCK_DDR
? 5 : 0;
else if (config->input_clock == ADV7511_INPUT_CLOCK_DDR)
input_id = config->embedded_sync ? 8 : 7;
else if (config->input_clock == ADV7511_INPUT_CLOCK_2X)
input_id = config->embedded_sync ? 4 : 3;
else
input_id = config->embedded_sync ? 2 : 1;
regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG, 0xf,
input_id);
regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x7e,
(color_depth << 4) |
(input_styles[config->input_style] << 2));
regmap_write(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG2,
config->input_justification << 3);
regmap_write(adv7511->regmap, ADV7511_REG_TIMING_GEN_SEQ,
config->sync_pulse << 2);
regmap_write(adv7511->regmap, 0xba, clock_delay << 5);
adv7511->embedded_sync = config->embedded_sync;
adv7511->hsync_polarity = config->hsync_polarity;
adv7511->vsync_polarity = config->vsync_polarity;
adv7511->rgb = config->input_colorspace == HDMI_COLORSPACE_RGB;
}
static void __adv7511_power_on(struct adv7511 *adv7511)
{
adv7511->current_edid_segment = -1;
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
ADV7511_POWER_POWER_DOWN, 0);
if (adv7511->i2c_main->irq) {
/*
* Documentation says the INT_ENABLE registers are reset in
* POWER_DOWN mode. My 7511w preserved the bits, however.
* Still, let's be safe and stick to the documentation.
*/
regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
ADV7511_INT0_EDID_READY | ADV7511_INT0_HPD);
regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1),
ADV7511_INT1_DDC_ERROR);
}
/*
* Per spec it is allowed to pulse the HPD signal to indicate that the
* EDID information has changed. Some monitors do this when they wakeup
* from standby or are enabled. When the HPD goes low the adv7511 is
* reset and the outputs are disabled which might cause the monitor to
* go to standby again. To avoid this we ignore the HPD pin for the
* first few seconds after enabling the output.
*/
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
ADV7511_REG_POWER2_HPD_SRC_MASK,
ADV7511_REG_POWER2_HPD_SRC_NONE);
}
static void adv7511_power_on(struct adv7511 *adv7511)
{
__adv7511_power_on(adv7511);
/*
* Most of the registers are reset during power down or when HPD is low.
*/
regcache_sync(adv7511->regmap);
if (adv7511->type == ADV7533)
adv7533_dsi_power_on(adv7511);
adv7511->powered = true;
}
static void __adv7511_power_off(struct adv7511 *adv7511)
{
/* TODO: setup additional power down modes */
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
ADV7511_POWER_POWER_DOWN,
ADV7511_POWER_POWER_DOWN);
regcache_mark_dirty(adv7511->regmap);
}
static void adv7511_power_off(struct adv7511 *adv7511)
{
__adv7511_power_off(adv7511);
if (adv7511->type == ADV7533)
adv7533_dsi_power_off(adv7511);
adv7511->powered = false;
}
/* -----------------------------------------------------------------------------
* Interrupt and hotplug detection
*/
static bool adv7511_hpd(struct adv7511 *adv7511)
{
unsigned int irq0;
int ret;
ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
if (ret < 0)
return false;
if (irq0 & ADV7511_INT0_HPD) {
regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
ADV7511_INT0_HPD);
return true;
}
return false;
}
static void adv7511_hpd_work(struct work_struct *work)
{
struct adv7511 *adv7511 = container_of(work, struct adv7511, hpd_work);
enum drm_connector_status status;
unsigned int val;
int ret;
ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
if (ret < 0)
status = connector_status_disconnected;
else if (val & ADV7511_STATUS_HPD)
status = connector_status_connected;
else
status = connector_status_disconnected;
if (adv7511->connector.status != status) {
adv7511->connector.status = status;
drm_kms_helper_hotplug_event(adv7511->connector.dev);
}
}
static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
{
unsigned int irq0, irq1;
int ret;
ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
if (ret < 0)
return ret;
ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(1), &irq1);
if (ret < 0)
return ret;
regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder)
schedule_work(&adv7511->hpd_work);
if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
adv7511->edid_read = true;
if (adv7511->i2c_main->irq)
wake_up_all(&adv7511->wq);
}
return 0;
}
static irqreturn_t adv7511_irq_handler(int irq, void *devid)
{
struct adv7511 *adv7511 = devid;
int ret;
ret = adv7511_irq_process(adv7511, true);
return ret < 0 ? IRQ_NONE : IRQ_HANDLED;
}
/* -----------------------------------------------------------------------------
* EDID retrieval
*/
static int adv7511_wait_for_edid(struct adv7511 *adv7511, int timeout)
{
int ret;
if (adv7511->i2c_main->irq) {
ret = wait_event_interruptible_timeout(adv7511->wq,
adv7511->edid_read, msecs_to_jiffies(timeout));
} else {
for (; timeout > 0; timeout -= 25) {
ret = adv7511_irq_process(adv7511, false);
if (ret < 0)
break;
if (adv7511->edid_read)
break;
msleep(25);
}
}
return adv7511->edid_read ? 0 : -EIO;
}
static int adv7511_get_edid_block(void *data, u8 *buf, unsigned int block,
size_t len)
{
struct adv7511 *adv7511 = data;
struct i2c_msg xfer[2];
uint8_t offset;
unsigned int i;
int ret;
if (len > 128)
return -EINVAL;
if (adv7511->current_edid_segment != block / 2) {
unsigned int status;
ret = regmap_read(adv7511->regmap, ADV7511_REG_DDC_STATUS,
&status);
if (ret < 0)
return ret;
if (status != 2) {
adv7511->edid_read = false;
regmap_write(adv7511->regmap, ADV7511_REG_EDID_SEGMENT,
block);
ret = adv7511_wait_for_edid(adv7511, 200);
if (ret < 0)
return ret;
}
/* Break this apart, hopefully more I2C controllers will
* support 64 byte transfers than 256 byte transfers
*/
xfer[0].addr = adv7511->i2c_edid->addr;
xfer[0].flags = 0;
xfer[0].len = 1;
xfer[0].buf = &offset;
xfer[1].addr = adv7511->i2c_edid->addr;
xfer[1].flags = I2C_M_RD;
xfer[1].len = 64;
xfer[1].buf = adv7511->edid_buf;
offset = 0;
for (i = 0; i < 4; ++i) {
ret = i2c_transfer(adv7511->i2c_edid->adapter, xfer,
ARRAY_SIZE(xfer));
if (ret < 0)
return ret;
else if (ret != 2)
return -EIO;
xfer[1].buf += 64;
offset += 64;
}
adv7511->current_edid_segment = block / 2;
}
if (block % 2 == 0)
memcpy(buf, adv7511->edid_buf, len);
else
memcpy(buf, adv7511->edid_buf + 128, len);
return 0;
}
/* -----------------------------------------------------------------------------
* ADV75xx helpers
*/
static int adv7511_get_modes(struct adv7511 *adv7511,
struct drm_connector *connector)
{
struct edid *edid;
unsigned int count;
/* Reading the EDID only works if the device is powered */
if (!adv7511->powered) {
unsigned int edid_i2c_addr =
(adv7511->i2c_main->addr << 1) + 4;
__adv7511_power_on(adv7511);
/* Reset the EDID_I2C_ADDR register as it might be cleared */
regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR,
edid_i2c_addr);
}
edid = drm_do_get_edid(connector, adv7511_get_edid_block, adv7511);
if (!adv7511->powered)
__adv7511_power_off(adv7511);
kfree(adv7511->edid);
adv7511->edid = edid;
if (!edid)
return 0;
drm_mode_connector_update_edid_property(connector, edid);
count = drm_add_edid_modes(connector, edid);
adv7511_set_config_csc(adv7511, connector, adv7511->rgb);
return count;
}
static enum drm_connector_status
adv7511_detect(struct adv7511 *adv7511, struct drm_connector *connector)
{
enum drm_connector_status status;
unsigned int val;
bool hpd;
int ret;
ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
if (ret < 0)
return connector_status_disconnected;
if (val & ADV7511_STATUS_HPD)
status = connector_status_connected;
else
status = connector_status_disconnected;
hpd = adv7511_hpd(adv7511);
/* The chip resets itself when the cable is disconnected, so in case
* there is a pending HPD interrupt and the cable is connected there was
* at least one transition from disconnected to connected and the chip
* has to be reinitialized. */
if (status == connector_status_connected && hpd && adv7511->powered) {
regcache_mark_dirty(adv7511->regmap);
adv7511_power_on(adv7511);
adv7511_get_modes(adv7511, connector);
if (adv7511->status == connector_status_connected)
status = connector_status_disconnected;
} else {
/* Renable HPD sensing */
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
ADV7511_REG_POWER2_HPD_SRC_MASK,
ADV7511_REG_POWER2_HPD_SRC_BOTH);
}
adv7511->status = status;
return status;
}
static int adv7511_mode_valid(struct adv7511 *adv7511,
struct drm_display_mode *mode)
{
if (mode->clock > 165000)
return MODE_CLOCK_HIGH;
return MODE_OK;
}
static void adv7511_mode_set(struct adv7511 *adv7511,
struct drm_display_mode *mode,
struct drm_display_mode *adj_mode)
{
unsigned int low_refresh_rate;
unsigned int hsync_polarity = 0;
unsigned int vsync_polarity = 0;
if (adv7511->embedded_sync) {
unsigned int hsync_offset, hsync_len;
unsigned int vsync_offset, vsync_len;
hsync_offset = adj_mode->crtc_hsync_start -
adj_mode->crtc_hdisplay;
vsync_offset = adj_mode->crtc_vsync_start -
adj_mode->crtc_vdisplay;
hsync_len = adj_mode->crtc_hsync_end -
adj_mode->crtc_hsync_start;
vsync_len = adj_mode->crtc_vsync_end -
adj_mode->crtc_vsync_start;
/* The hardware vsync generator has a off-by-one bug */
vsync_offset += 1;
regmap_write(adv7511->regmap, ADV7511_REG_HSYNC_PLACEMENT_MSB,
((hsync_offset >> 10) & 0x7) << 5);
regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(0),
(hsync_offset >> 2) & 0xff);
regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(1),
((hsync_offset & 0x3) << 6) |
((hsync_len >> 4) & 0x3f));
regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(2),
((hsync_len & 0xf) << 4) |
((vsync_offset >> 6) & 0xf));
regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(3),
((vsync_offset & 0x3f) << 2) |
((vsync_len >> 8) & 0x3));
regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(4),
vsync_len & 0xff);
hsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PHSYNC);
vsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PVSYNC);
} else {
enum adv7511_sync_polarity mode_hsync_polarity;
enum adv7511_sync_polarity mode_vsync_polarity;
/**
* If the input signal is always low or always high we want to
* invert or let it passthrough depending on the polarity of the
* current mode.
**/
if (adj_mode->flags & DRM_MODE_FLAG_NHSYNC)
mode_hsync_polarity = ADV7511_SYNC_POLARITY_LOW;
else
mode_hsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
if (adj_mode->flags & DRM_MODE_FLAG_NVSYNC)
mode_vsync_polarity = ADV7511_SYNC_POLARITY_LOW;
else
mode_vsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
if (adv7511->hsync_polarity != mode_hsync_polarity &&
adv7511->hsync_polarity !=
ADV7511_SYNC_POLARITY_PASSTHROUGH)
hsync_polarity = 1;
if (adv7511->vsync_polarity != mode_vsync_polarity &&
adv7511->vsync_polarity !=
ADV7511_SYNC_POLARITY_PASSTHROUGH)
vsync_polarity = 1;
}
if (mode->vrefresh <= 24000)
low_refresh_rate = ADV7511_LOW_REFRESH_RATE_24HZ;
else if (mode->vrefresh <= 25000)
low_refresh_rate = ADV7511_LOW_REFRESH_RATE_25HZ;
else if (mode->vrefresh <= 30000)
low_refresh_rate = ADV7511_LOW_REFRESH_RATE_30HZ;
else
low_refresh_rate = ADV7511_LOW_REFRESH_RATE_NONE;
regmap_update_bits(adv7511->regmap, 0xfb,
0x6, low_refresh_rate << 1);
regmap_update_bits(adv7511->regmap, 0x17,
0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
if (adv7511->type == ADV7533)
adv7533_mode_set(adv7511, adj_mode);
drm_mode_copy(&adv7511->curr_mode, adj_mode);
/*
* TODO Test first order 4:2:2 to 4:4:4 up conversion method, which is
* supposed to give better results.
*/
adv7511->f_tmds = mode->clock;
}
/* Connector funcs */
static struct adv7511 *connector_to_adv7511(struct drm_connector *connector)
{
return container_of(connector, struct adv7511, connector);
}
static int adv7511_connector_get_modes(struct drm_connector *connector)
{
struct adv7511 *adv = connector_to_adv7511(connector);
return adv7511_get_modes(adv, connector);
}
static enum drm_mode_status
adv7511_connector_mode_valid(struct drm_connector *connector,
struct drm_display_mode *mode)
{
struct adv7511 *adv = connector_to_adv7511(connector);
return adv7511_mode_valid(adv, mode);
}
static struct drm_connector_helper_funcs adv7511_connector_helper_funcs = {
.get_modes = adv7511_connector_get_modes,
.mode_valid = adv7511_connector_mode_valid,
};
static enum drm_connector_status
adv7511_connector_detect(struct drm_connector *connector, bool force)
{
struct adv7511 *adv = connector_to_adv7511(connector);
return adv7511_detect(adv, connector);
}
static struct drm_connector_funcs adv7511_connector_funcs = {
.dpms = drm_atomic_helper_connector_dpms,
.fill_modes = drm_helper_probe_single_connector_modes,
.detect = adv7511_connector_detect,
.destroy = drm_connector_cleanup,
.reset = drm_atomic_helper_connector_reset,
.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
};
/* Bridge funcs */
static struct adv7511 *bridge_to_adv7511(struct drm_bridge *bridge)
{
return container_of(bridge, struct adv7511, bridge);
}
static void adv7511_bridge_enable(struct drm_bridge *bridge)
{
struct adv7511 *adv = bridge_to_adv7511(bridge);
adv7511_power_on(adv);
}
static void adv7511_bridge_disable(struct drm_bridge *bridge)
{
struct adv7511 *adv = bridge_to_adv7511(bridge);
adv7511_power_off(adv);
}
static void adv7511_bridge_mode_set(struct drm_bridge *bridge,
struct drm_display_mode *mode,
struct drm_display_mode *adj_mode)
{
struct adv7511 *adv = bridge_to_adv7511(bridge);
adv7511_mode_set(adv, mode, adj_mode);
}
static int adv7511_bridge_attach(struct drm_bridge *bridge)
{
struct adv7511 *adv = bridge_to_adv7511(bridge);
int ret;
if (!bridge->encoder) {
DRM_ERROR("Parent encoder object not found");
return -ENODEV;
}
adv->connector.polled = DRM_CONNECTOR_POLL_HPD;
ret = drm_connector_init(bridge->dev, &adv->connector,
&adv7511_connector_funcs,
DRM_MODE_CONNECTOR_HDMIA);
if (ret) {
DRM_ERROR("Failed to initialize connector with drm\n");
return ret;
}
drm_connector_helper_add(&adv->connector,
&adv7511_connector_helper_funcs);
drm_mode_connector_attach_encoder(&adv->connector, bridge->encoder);
if (adv->type == ADV7533)
ret = adv7533_attach_dsi(adv);
if (adv->i2c_main->irq)
regmap_write(adv->regmap, ADV7511_REG_INT_ENABLE(0),
ADV7511_INT0_HPD);
return ret;
}
static struct drm_bridge_funcs adv7511_bridge_funcs = {
.enable = adv7511_bridge_enable,
.disable = adv7511_bridge_disable,
.mode_set = adv7511_bridge_mode_set,
.attach = adv7511_bridge_attach,
};
/* -----------------------------------------------------------------------------
* Probe & remove
*/
static const char * const adv7511_supply_names[] = {
"avdd",
"dvdd",
"pvdd",
"bgvdd",
"dvdd-3v",
};
static const char * const adv7533_supply_names[] = {
"avdd",
"dvdd",
"pvdd",
"a2vdd",
"v3p3",
"v1p2",
};
static int adv7511_init_regulators(struct adv7511 *adv)
{
struct device *dev = &adv->i2c_main->dev;
const char * const *supply_names;
unsigned int i;
int ret;
if (adv->type == ADV7511) {
supply_names = adv7511_supply_names;
adv->num_supplies = ARRAY_SIZE(adv7511_supply_names);
} else {
supply_names = adv7533_supply_names;
adv->num_supplies = ARRAY_SIZE(adv7533_supply_names);
}
adv->supplies = devm_kcalloc(dev, adv->num_supplies,
sizeof(*adv->supplies), GFP_KERNEL);
if (!adv->supplies)
return -ENOMEM;
for (i = 0; i < adv->num_supplies; i++)
adv->supplies[i].supply = supply_names[i];
ret = devm_regulator_bulk_get(dev, adv->num_supplies, adv->supplies);
if (ret)
return ret;
return regulator_bulk_enable(adv->num_supplies, adv->supplies);
}
static void adv7511_uninit_regulators(struct adv7511 *adv)
{
regulator_bulk_disable(adv->num_supplies, adv->supplies);
}
static int adv7511_parse_dt(struct device_node *np,
struct adv7511_link_config *config)
{
const char *str;
int ret;
of_property_read_u32(np, "adi,input-depth", &config->input_color_depth);
if (config->input_color_depth != 8 && config->input_color_depth != 10 &&
config->input_color_depth != 12)
return -EINVAL;
ret = of_property_read_string(np, "adi,input-colorspace", &str);
if (ret < 0)
return ret;
if (!strcmp(str, "rgb"))
config->input_colorspace = HDMI_COLORSPACE_RGB;
else if (!strcmp(str, "yuv422"))
config->input_colorspace = HDMI_COLORSPACE_YUV422;
else if (!strcmp(str, "yuv444"))
config->input_colorspace = HDMI_COLORSPACE_YUV444;
else
return -EINVAL;
ret = of_property_read_string(np, "adi,input-clock", &str);
if (ret < 0)
return ret;
if (!strcmp(str, "1x"))
config->input_clock = ADV7511_INPUT_CLOCK_1X;
else if (!strcmp(str, "2x"))
config->input_clock = ADV7511_INPUT_CLOCK_2X;
else if (!strcmp(str, "ddr"))
config->input_clock = ADV7511_INPUT_CLOCK_DDR;
else
return -EINVAL;
if (config->input_colorspace == HDMI_COLORSPACE_YUV422 ||
config->input_clock != ADV7511_INPUT_CLOCK_1X) {
ret = of_property_read_u32(np, "adi,input-style",
&config->input_style);
if (ret)
return ret;
if (config->input_style < 1 || config->input_style > 3)
return -EINVAL;
ret = of_property_read_string(np, "adi,input-justification",
&str);
if (ret < 0)
return ret;
if (!strcmp(str, "left"))
config->input_justification =
ADV7511_INPUT_JUSTIFICATION_LEFT;
else if (!strcmp(str, "evenly"))
config->input_justification =
ADV7511_INPUT_JUSTIFICATION_EVENLY;
else if (!strcmp(str, "right"))
config->input_justification =
ADV7511_INPUT_JUSTIFICATION_RIGHT;
else
return -EINVAL;
} else {
config->input_style = 1;
config->input_justification = ADV7511_INPUT_JUSTIFICATION_LEFT;
}
of_property_read_u32(np, "adi,clock-delay", &config->clock_delay);
if (config->clock_delay < -1200 || config->clock_delay > 1600)
return -EINVAL;
config->embedded_sync = of_property_read_bool(np, "adi,embedded-sync");
/* Hardcode the sync pulse configurations for now. */
config->sync_pulse = ADV7511_INPUT_SYNC_PULSE_NONE;
config->vsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
config->hsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
return 0;
}
static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
{
struct adv7511_link_config link_config;
struct adv7511 *adv7511;
struct device *dev = &i2c->dev;
unsigned int main_i2c_addr = i2c->addr << 1;
unsigned int edid_i2c_addr = main_i2c_addr + 4;
unsigned int val;
int ret;
if (!dev->of_node)
return -EINVAL;
adv7511 = devm_kzalloc(dev, sizeof(*adv7511), GFP_KERNEL);
if (!adv7511)
return -ENOMEM;
adv7511->i2c_main = i2c;
adv7511->powered = false;
adv7511->status = connector_status_disconnected;
if (dev->of_node)
adv7511->type = (enum adv7511_type)of_device_get_match_data(dev);
else
adv7511->type = id->driver_data;
memset(&link_config, 0, sizeof(link_config));
if (adv7511->type == ADV7511)
ret = adv7511_parse_dt(dev->of_node, &link_config);
else
ret = adv7533_parse_dt(dev->of_node, adv7511);
if (ret)
return ret;
ret = adv7511_init_regulators(adv7511);
if (ret) {
dev_err(dev, "failed to init regulators\n");
return ret;
}
/*
* The power down GPIO is optional. If present, toggle it from active to
* inactive to wake up the encoder.
*/
adv7511->gpio_pd = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH);
if (IS_ERR(adv7511->gpio_pd)) {
ret = PTR_ERR(adv7511->gpio_pd);
goto uninit_regulators;
}
if (adv7511->gpio_pd) {
mdelay(5);
gpiod_set_value_cansleep(adv7511->gpio_pd, 0);
}
adv7511->regmap = devm_regmap_init_i2c(i2c, &adv7511_regmap_config);
if (IS_ERR(adv7511->regmap)) {
ret = PTR_ERR(adv7511->regmap);
goto uninit_regulators;
}
ret = regmap_read(adv7511->regmap, ADV7511_REG_CHIP_REVISION, &val);
if (ret)
goto uninit_regulators;
dev_dbg(dev, "Rev. %d\n", val);
if (adv7511->type == ADV7511)
ret = regmap_register_patch(adv7511->regmap,
adv7511_fixed_registers,
ARRAY_SIZE(adv7511_fixed_registers));
else
ret = adv7533_patch_registers(adv7511);
if (ret)
goto uninit_regulators;
regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR, edid_i2c_addr);
regmap_write(adv7511->regmap, ADV7511_REG_PACKET_I2C_ADDR,
main_i2c_addr - 0xa);
regmap_write(adv7511->regmap, ADV7511_REG_CEC_I2C_ADDR,
main_i2c_addr - 2);
adv7511_packet_disable(adv7511, 0xffff);
adv7511->i2c_edid = i2c_new_dummy(i2c->adapter, edid_i2c_addr >> 1);
if (!adv7511->i2c_edid) {
ret = -ENOMEM;
goto uninit_regulators;
}
if (adv7511->type == ADV7533) {
ret = adv7533_init_cec(adv7511);
if (ret)
goto err_i2c_unregister_edid;
}
INIT_WORK(&adv7511->hpd_work, adv7511_hpd_work);
if (i2c->irq) {
init_waitqueue_head(&adv7511->wq);
ret = devm_request_threaded_irq(dev, i2c->irq, NULL,
adv7511_irq_handler,
IRQF_ONESHOT, dev_name(dev),
adv7511);
if (ret)
goto err_unregister_cec;
}
/* CEC is unused for now */
regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL,
ADV7511_CEC_CTRL_POWER_DOWN);
adv7511_power_off(adv7511);
i2c_set_clientdata(i2c, adv7511);
if (adv7511->type == ADV7511)
adv7511_set_link_config(adv7511, &link_config);
adv7511->bridge.funcs = &adv7511_bridge_funcs;
adv7511->bridge.of_node = dev->of_node;
ret = drm_bridge_add(&adv7511->bridge);
if (ret) {
dev_err(dev, "failed to add adv7511 bridge\n");
goto err_unregister_cec;
}
adv7511_audio_init(dev, adv7511);
return 0;
err_unregister_cec:
adv7533_uninit_cec(adv7511);
err_i2c_unregister_edid:
i2c_unregister_device(adv7511->i2c_edid);
uninit_regulators:
adv7511_uninit_regulators(adv7511);
return ret;
}
static int adv7511_remove(struct i2c_client *i2c)
{
struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
if (adv7511->type == ADV7533) {
adv7533_detach_dsi(adv7511);
adv7533_uninit_cec(adv7511);
}
adv7511_uninit_regulators(adv7511);
drm_bridge_remove(&adv7511->bridge);
adv7511_audio_exit(adv7511);
i2c_unregister_device(adv7511->i2c_edid);
kfree(adv7511->edid);
return 0;
}
static const struct i2c_device_id adv7511_i2c_ids[] = {
{ "adv7511", ADV7511 },
{ "adv7511w", ADV7511 },
{ "adv7513", ADV7511 },
#ifdef CONFIG_DRM_I2C_ADV7533
{ "adv7533", ADV7533 },
#endif
{ }
};
MODULE_DEVICE_TABLE(i2c, adv7511_i2c_ids);
static const struct of_device_id adv7511_of_ids[] = {
{ .compatible = "adi,adv7511", .data = (void *)ADV7511 },
{ .compatible = "adi,adv7511w", .data = (void *)ADV7511 },
{ .compatible = "adi,adv7513", .data = (void *)ADV7511 },
#ifdef CONFIG_DRM_I2C_ADV7533
{ .compatible = "adi,adv7533", .data = (void *)ADV7533 },
#endif
{ }
};
MODULE_DEVICE_TABLE(of, adv7511_of_ids);
static struct mipi_dsi_driver adv7533_dsi_driver = {
.driver.name = "adv7533",
};
static struct i2c_driver adv7511_driver = {
.driver = {
.name = "adv7511",
.of_match_table = adv7511_of_ids,
},
.id_table = adv7511_i2c_ids,
.probe = adv7511_probe,
.remove = adv7511_remove,
};
static int __init adv7511_init(void)
{
if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
mipi_dsi_driver_register(&adv7533_dsi_driver);
return i2c_add_driver(&adv7511_driver);
}
module_init(adv7511_init);
static void __exit adv7511_exit(void)
{
i2c_del_driver(&adv7511_driver);
if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
mipi_dsi_driver_unregister(&adv7533_dsi_driver);
}
module_exit(adv7511_exit);
MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
MODULE_DESCRIPTION("ADV7511 HDMI transmitter driver");
MODULE_LICENSE("GPL");
Reference in New Issue View Git Blame Copy Permalink