mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-05 04:36:45 +07:00
339e834fe0
Add device nodes for the HS USB Host port 1, USB PHY and its required regulator and also pin mux setup for HS USB1 pins. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
218 lines
5.1 KiB
Plaintext
218 lines
5.1 KiB
Plaintext
/*
|
|
* Device Tree Source for IGEPv2 board
|
|
*
|
|
* Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
|
|
* Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include "omap3-igep.dtsi"
|
|
|
|
/ {
|
|
model = "IGEPv2";
|
|
compatible = "isee,omap3-igep0020", "ti,omap3";
|
|
|
|
leds {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&leds_pins>;
|
|
compatible = "gpio-leds";
|
|
|
|
boot {
|
|
label = "omap3:green:boot";
|
|
gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
user0 {
|
|
label = "omap3:red:user0";
|
|
gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
user1 {
|
|
label = "omap3:red:user1";
|
|
gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
user2 {
|
|
label = "omap3:green:user1";
|
|
gpios = <&twl_gpio 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
vddvario: regulator-vddvario {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vddvario";
|
|
regulator-always-on;
|
|
};
|
|
|
|
vdd33a: regulator-vdd33a {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vdd33a";
|
|
regulator-always-on;
|
|
};
|
|
|
|
/* HS USB Port 1 Power */
|
|
hsusb1_power: hsusb1_power_reg {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "hsusb1_vbus";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* GPIO LEDA */
|
|
startup-delay-us = <70000>;
|
|
};
|
|
|
|
/* HS USB Host PHY on PORT 1 */
|
|
hsusb1_phy: hsusb1_phy {
|
|
compatible = "usb-nop-xceiv";
|
|
reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
|
|
vcc-supply = <&hsusb1_power>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <
|
|
&hsusbb1_pins
|
|
>;
|
|
|
|
hsusbb1_pins: pinmux_hsusbb1_pins {
|
|
pinctrl-single,pins = <
|
|
0x5aa (PIN_OUTPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */
|
|
0x5a8 (PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */
|
|
0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d8.hsusb1_dir */
|
|
0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d9.hsusb1_nxt */
|
|
0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d0.hsusb1_data0 */
|
|
0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d1.hsusb1_data1 */
|
|
0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d2.hsusb1_data2 */
|
|
0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d3.hsusb1_data7 */
|
|
0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d4.hsusb1_data4 */
|
|
0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d5.hsusb1_data5 */
|
|
0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d6.hsusb1_data6 */
|
|
0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&leds_pins {
|
|
pinctrl-single,pins = <
|
|
0x5c4 (PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */
|
|
0x5c6 (PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
|
|
0x5c8 (PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */
|
|
>;
|
|
};
|
|
|
|
&i2c3 {
|
|
clock-frequency = <100000>;
|
|
|
|
/*
|
|
* Display monitor features are burnt in the EEPROM
|
|
* as EDID data.
|
|
*/
|
|
eeprom@50 {
|
|
compatible = "ti,eeprom";
|
|
reg = <0x50>;
|
|
};
|
|
};
|
|
|
|
&gpmc {
|
|
ranges = <0 0 0x00000000 0x20000000>,
|
|
<5 0 0x2c000000 0x01000000>;
|
|
|
|
nand@0,0 {
|
|
linux,mtd-name= "micron,mt29c4g96maz";
|
|
reg = <0 0 0>;
|
|
nand-bus-width = <16>;
|
|
ti,nand-ecc-opt = "bch8";
|
|
|
|
gpmc,sync-clk-ps = <0>;
|
|
gpmc,cs-on-ns = <0>;
|
|
gpmc,cs-rd-off-ns = <44>;
|
|
gpmc,cs-wr-off-ns = <44>;
|
|
gpmc,adv-on-ns = <6>;
|
|
gpmc,adv-rd-off-ns = <34>;
|
|
gpmc,adv-wr-off-ns = <44>;
|
|
gpmc,we-off-ns = <40>;
|
|
gpmc,oe-off-ns = <54>;
|
|
gpmc,access-ns = <64>;
|
|
gpmc,rd-cycle-ns = <82>;
|
|
gpmc,wr-cycle-ns = <82>;
|
|
gpmc,wr-access-ns = <40>;
|
|
gpmc,wr-data-mux-bus-ns = <0>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "SPL";
|
|
reg = <0 0x100000>;
|
|
};
|
|
partition@80000 {
|
|
label = "U-Boot";
|
|
reg = <0x100000 0x180000>;
|
|
};
|
|
partition@1c0000 {
|
|
label = "Environment";
|
|
reg = <0x280000 0x100000>;
|
|
};
|
|
partition@280000 {
|
|
label = "Kernel";
|
|
reg = <0x380000 0x300000>;
|
|
};
|
|
partition@780000 {
|
|
label = "Filesystem";
|
|
reg = <0x680000 0x1f980000>;
|
|
};
|
|
};
|
|
|
|
ethernet@5,0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&smsc911x_pins>;
|
|
compatible = "smsc,lan9221", "smsc,lan9115";
|
|
reg = <5 0 0xff>;
|
|
bank-width = <2>;
|
|
|
|
gpmc,mux-add-data;
|
|
gpmc,cs-on-ns = <0>;
|
|
gpmc,cs-rd-off-ns = <186>;
|
|
gpmc,cs-wr-off-ns = <186>;
|
|
gpmc,adv-on-ns = <12>;
|
|
gpmc,adv-rd-off-ns = <48>;
|
|
gpmc,adv-wr-off-ns = <48>;
|
|
gpmc,oe-on-ns = <54>;
|
|
gpmc,oe-off-ns = <168>;
|
|
gpmc,we-on-ns = <54>;
|
|
gpmc,we-off-ns = <168>;
|
|
gpmc,rd-cycle-ns = <186>;
|
|
gpmc,wr-cycle-ns = <186>;
|
|
gpmc,access-ns = <114>;
|
|
gpmc,page-burst-access-ns = <6>;
|
|
gpmc,bus-turnaround-ns = <12>;
|
|
gpmc,cycle2cycle-delay-ns = <18>;
|
|
gpmc,wr-data-mux-bus-ns = <90>;
|
|
gpmc,wr-access-ns = <186>;
|
|
gpmc,cycle2cycle-samecsen;
|
|
gpmc,cycle2cycle-diffcsen;
|
|
|
|
interrupt-parent = <&gpio6>;
|
|
interrupts = <16 8>;
|
|
vmmc-supply = <&vddvario>;
|
|
vmmc_aux-supply = <&vdd33a>;
|
|
reg-io-width = <4>;
|
|
|
|
smsc,save-mac-address;
|
|
};
|
|
};
|
|
|
|
&usbhshost {
|
|
port1-mode = "ehci-phy";
|
|
};
|
|
|
|
&usbhsehci {
|
|
phys = <&hsusb1_phy>;
|
|
};
|