mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-30 07:26:46 +07:00
63aa945b10
We support decoding the bootloader values if DEBUG is defined. But we also need to change the struct omap_hwmod flags to have HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the boot. Otherwise just the default timings will be displayed instead of the bootloader configured timings. This also allows us to clean up the various GPMC related hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET, and HWMOD_INIT_NO_IDLE is not needed. Cc: Brian Hutchinson <b.hutchman@gmail.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
106 lines
3.3 KiB
Plaintext
106 lines
3.3 KiB
Plaintext
#
|
|
# Memory devices
|
|
#
|
|
|
|
menuconfig MEMORY
|
|
bool "Memory Controller drivers"
|
|
|
|
if MEMORY
|
|
|
|
config ATMEL_SDRAMC
|
|
bool "Atmel (Multi-port DDR-)SDRAM Controller"
|
|
default y
|
|
depends on ARCH_AT91 && OF
|
|
help
|
|
This driver is for Atmel SDRAM Controller or Atmel Multi-port
|
|
DDR-SDRAM Controller available on Atmel AT91SAM9 and SAMA5 SoCs.
|
|
Starting with the at91sam9g45, this controller supports SDR, DDR and
|
|
LP-DDR memories.
|
|
|
|
config TI_AEMIF
|
|
tristate "Texas Instruments AEMIF driver"
|
|
depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
|
|
help
|
|
This driver is for the AEMIF module available in Texas Instruments
|
|
SoCs. AEMIF stands for Asynchronous External Memory Interface and
|
|
is intended to provide a glue-less interface to a variety of
|
|
asynchronuous memory devices like ASRAM, NOR and NAND memory. A total
|
|
of 256M bytes of any of these memories can be accessed at a given
|
|
time via four chip selects with 64M byte access per chip select.
|
|
|
|
config TI_EMIF
|
|
tristate "Texas Instruments EMIF driver"
|
|
depends on ARCH_OMAP2PLUS
|
|
select DDR
|
|
help
|
|
This driver is for the EMIF module available in Texas Instruments
|
|
SoCs. EMIF is an SDRAM controller that, based on its revision,
|
|
supports one or more of DDR2, DDR3, and LPDDR2 SDRAM protocols.
|
|
This driver takes care of only LPDDR2 memories presently. The
|
|
functions of the driver includes re-configuring AC timing
|
|
parameters and other settings during frequency, voltage and
|
|
temperature changes
|
|
|
|
config OMAP_GPMC
|
|
bool
|
|
help
|
|
This driver is for the General Purpose Memory Controller (GPMC)
|
|
present on Texas Instruments SoCs (e.g. OMAP2+). GPMC allows
|
|
interfacing to a variety of asynchronous as well as synchronous
|
|
memory drives like NOR, NAND, OneNAND, SRAM.
|
|
|
|
config OMAP_GPMC_DEBUG
|
|
bool
|
|
depends on OMAP_GPMC
|
|
help
|
|
Enables verbose debugging mostly to decode the bootloader provided
|
|
timings. Enable this during development to configure devices
|
|
connected to the GPMC bus.
|
|
|
|
config MVEBU_DEVBUS
|
|
bool "Marvell EBU Device Bus Controller"
|
|
default y
|
|
depends on PLAT_ORION && OF
|
|
help
|
|
This driver is for the Device Bus controller available in some
|
|
Marvell EBU SoCs such as Discovery (mv78xx0), Orion (88f5xxx) and
|
|
Armada 370 and Armada XP. This controller allows to handle flash
|
|
devices such as NOR, NAND, SRAM, and FPGA.
|
|
|
|
config TEGRA20_MC
|
|
bool "Tegra20 Memory Controller(MC) driver"
|
|
default y
|
|
depends on ARCH_TEGRA_2x_SOC
|
|
help
|
|
This driver is for the Memory Controller(MC) module available
|
|
in Tegra20 SoCs, mainly for a address translation fault
|
|
analysis, especially for IOMMU/GART(Graphics Address
|
|
Relocation Table) module.
|
|
|
|
config FSL_CORENET_CF
|
|
tristate "Freescale CoreNet Error Reporting"
|
|
depends on FSL_SOC_BOOKE
|
|
help
|
|
Say Y for reporting of errors from the Freescale CoreNet
|
|
Coherency Fabric. Errors reported include accesses to
|
|
physical addresses that mapped by no local access window
|
|
(LAW) or an invalid LAW, as well as bad cache state that
|
|
represents a coherency violation.
|
|
|
|
config FSL_IFC
|
|
bool
|
|
depends on FSL_SOC
|
|
|
|
config JZ4780_NEMC
|
|
bool "Ingenic JZ4780 SoC NEMC driver"
|
|
default y
|
|
depends on MACH_JZ4780
|
|
help
|
|
This driver is for the NAND/External Memory Controller (NEMC) in
|
|
the Ingenic JZ4780. This controller is used to handle external
|
|
memory devices such as NAND and SRAM.
|
|
|
|
source "drivers/memory/tegra/Kconfig"
|
|
|
|
endif
|