linux_dsm_epyc7002/drivers/net/ethernet/hisilicon/hns_mdio.c
Yonglong Liu cec8abba13 net: hns: Fix wrong read accesses via Clause 45 MDIO protocol
When reading phy registers via Clause 45 MDIO protocol, after write
address operation, the driver use another write address operation, so
can not read the right value of any phy registers. This patch fixes it.

Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-27 23:01:56 -08:00

582 lines
14 KiB
C

/*
* Copyright (c) 2014-2015 Hisilicon Limited.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/acpi.h>
#include <linux/errno.h>
#include <linux/etherdevice.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/netdevice.h>
#include <linux/of_address.h>
#include <linux/of.h>
#include <linux/of_mdio.h>
#include <linux/of_platform.h>
#include <linux/phy.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#define MDIO_DRV_NAME "Hi-HNS_MDIO"
#define MDIO_BUS_NAME "Hisilicon MII Bus"
#define MDIO_TIMEOUT 1000000
struct hns_mdio_sc_reg {
u16 mdio_clk_en;
u16 mdio_clk_dis;
u16 mdio_reset_req;
u16 mdio_reset_dreq;
u16 mdio_clk_st;
u16 mdio_reset_st;
};
struct hns_mdio_device {
void *vbase; /* mdio reg base address */
struct regmap *subctrl_vbase;
struct hns_mdio_sc_reg sc_reg;
};
/* mdio reg */
#define MDIO_COMMAND_REG 0x0
#define MDIO_ADDR_REG 0x4
#define MDIO_WDATA_REG 0x8
#define MDIO_RDATA_REG 0xc
#define MDIO_STA_REG 0x10
/* cfg phy bit map */
#define MDIO_CMD_DEVAD_M 0x1f
#define MDIO_CMD_DEVAD_S 0
#define MDIO_CMD_PRTAD_M 0x1f
#define MDIO_CMD_PRTAD_S 5
#define MDIO_CMD_OP_S 10
#define MDIO_CMD_ST_S 12
#define MDIO_CMD_START_B 14
#define MDIO_ADDR_DATA_M 0xffff
#define MDIO_ADDR_DATA_S 0
#define MDIO_WDATA_DATA_M 0xffff
#define MDIO_WDATA_DATA_S 0
#define MDIO_RDATA_DATA_M 0xffff
#define MDIO_RDATA_DATA_S 0
#define MDIO_STATE_STA_B 0
enum mdio_st_clause {
MDIO_ST_CLAUSE_45 = 0,
MDIO_ST_CLAUSE_22
};
enum mdio_c22_op_seq {
MDIO_C22_WRITE = 1,
MDIO_C22_READ = 2
};
enum mdio_c45_op_seq {
MDIO_C45_WRITE_ADDR = 0,
MDIO_C45_WRITE_DATA,
MDIO_C45_READ_INCREMENT,
MDIO_C45_READ
};
/* peri subctrl reg */
#define MDIO_SC_CLK_EN 0x338
#define MDIO_SC_CLK_DIS 0x33C
#define MDIO_SC_RESET_REQ 0xA38
#define MDIO_SC_RESET_DREQ 0xA3C
#define MDIO_SC_CLK_ST 0x531C
#define MDIO_SC_RESET_ST 0x5A1C
static void mdio_write_reg(void *base, u32 reg, u32 value)
{
u8 __iomem *reg_addr = (u8 __iomem *)base;
writel_relaxed(value, reg_addr + reg);
}
#define MDIO_WRITE_REG(a, reg, value) \
mdio_write_reg((a)->vbase, (reg), (value))
static u32 mdio_read_reg(void *base, u32 reg)
{
u8 __iomem *reg_addr = (u8 __iomem *)base;
return readl_relaxed(reg_addr + reg);
}
#define mdio_set_field(origin, mask, shift, val) \
do { \
(origin) &= (~((mask) << (shift))); \
(origin) |= (((val) & (mask)) << (shift)); \
} while (0)
#define mdio_get_field(origin, mask, shift) (((origin) >> (shift)) & (mask))
static void mdio_set_reg_field(void *base, u32 reg, u32 mask, u32 shift,
u32 val)
{
u32 origin = mdio_read_reg(base, reg);
mdio_set_field(origin, mask, shift, val);
mdio_write_reg(base, reg, origin);
}
#define MDIO_SET_REG_FIELD(dev, reg, mask, shift, val) \
mdio_set_reg_field((dev)->vbase, (reg), (mask), (shift), (val))
static u32 mdio_get_reg_field(void *base, u32 reg, u32 mask, u32 shift)
{
u32 origin;
origin = mdio_read_reg(base, reg);
return mdio_get_field(origin, mask, shift);
}
#define MDIO_GET_REG_FIELD(dev, reg, mask, shift) \
mdio_get_reg_field((dev)->vbase, (reg), (mask), (shift))
#define MDIO_GET_REG_BIT(dev, reg, bit) \
mdio_get_reg_field((dev)->vbase, (reg), 0x1ull, (bit))
#define MDIO_CHECK_SET_ST 1
#define MDIO_CHECK_CLR_ST 0
static int mdio_sc_cfg_reg_write(struct hns_mdio_device *mdio_dev,
u32 cfg_reg, u32 set_val,
u32 st_reg, u32 st_msk, u8 check_st)
{
u32 time_cnt;
u32 reg_value;
regmap_write(mdio_dev->subctrl_vbase, cfg_reg, set_val);
for (time_cnt = MDIO_TIMEOUT; time_cnt; time_cnt--) {
regmap_read(mdio_dev->subctrl_vbase, st_reg, &reg_value);
reg_value &= st_msk;
if ((!!check_st) == (!!reg_value))
break;
}
if ((!!check_st) != (!!reg_value))
return -EBUSY;
return 0;
}
static int hns_mdio_wait_ready(struct mii_bus *bus)
{
struct hns_mdio_device *mdio_dev = bus->priv;
u32 cmd_reg_value;
int i;
/* waitting for MDIO_COMMAND_REG 's mdio_start==0 */
/* after that can do read or write*/
for (i = 0; i < MDIO_TIMEOUT; i++) {
cmd_reg_value = MDIO_GET_REG_BIT(mdio_dev,
MDIO_COMMAND_REG,
MDIO_CMD_START_B);
if (!cmd_reg_value)
break;
}
if ((i == MDIO_TIMEOUT) && cmd_reg_value)
return -ETIMEDOUT;
return 0;
}
static void hns_mdio_cmd_write(struct hns_mdio_device *mdio_dev,
u8 is_c45, u8 op, u8 phy_id, u16 cmd)
{
u32 cmd_reg_value;
u8 st = is_c45 ? MDIO_ST_CLAUSE_45 : MDIO_ST_CLAUSE_22;
cmd_reg_value = st << MDIO_CMD_ST_S;
cmd_reg_value |= op << MDIO_CMD_OP_S;
cmd_reg_value |=
(phy_id & MDIO_CMD_PRTAD_M) << MDIO_CMD_PRTAD_S;
cmd_reg_value |= (cmd & MDIO_CMD_DEVAD_M) << MDIO_CMD_DEVAD_S;
cmd_reg_value |= 1 << MDIO_CMD_START_B;
MDIO_WRITE_REG(mdio_dev, MDIO_COMMAND_REG, cmd_reg_value);
}
/**
* hns_mdio_write - access phy register
* @bus: mdio bus
* @phy_id: phy id
* @regnum: register num
* @value: register value
*
* Return 0 on success, negative on failure
*/
static int hns_mdio_write(struct mii_bus *bus,
int phy_id, int regnum, u16 data)
{
int ret;
struct hns_mdio_device *mdio_dev = (struct hns_mdio_device *)bus->priv;
u8 devad = ((regnum >> 16) & 0x1f);
u8 is_c45 = !!(regnum & MII_ADDR_C45);
u16 reg = (u16)(regnum & 0xffff);
u8 op;
u16 cmd_reg_cfg;
dev_dbg(&bus->dev, "mdio write %s,base is %p\n",
bus->id, mdio_dev->vbase);
dev_dbg(&bus->dev, "phy id=%d, is_c45=%d, devad=%d, reg=%#x, write data=%d\n",
phy_id, is_c45, devad, reg, data);
/* wait for ready */
ret = hns_mdio_wait_ready(bus);
if (ret) {
dev_err(&bus->dev, "MDIO bus is busy\n");
return ret;
}
if (!is_c45) {
cmd_reg_cfg = reg;
op = MDIO_C22_WRITE;
} else {
/* config the cmd-reg to write addr*/
MDIO_SET_REG_FIELD(mdio_dev, MDIO_ADDR_REG, MDIO_ADDR_DATA_M,
MDIO_ADDR_DATA_S, reg);
hns_mdio_cmd_write(mdio_dev, is_c45,
MDIO_C45_WRITE_ADDR, phy_id, devad);
/* check for read or write opt is finished */
ret = hns_mdio_wait_ready(bus);
if (ret) {
dev_err(&bus->dev, "MDIO bus is busy\n");
return ret;
}
/* config the data needed writing */
cmd_reg_cfg = devad;
op = MDIO_C45_WRITE_DATA;
}
MDIO_SET_REG_FIELD(mdio_dev, MDIO_WDATA_REG, MDIO_WDATA_DATA_M,
MDIO_WDATA_DATA_S, data);
hns_mdio_cmd_write(mdio_dev, is_c45, op, phy_id, cmd_reg_cfg);
return 0;
}
/**
* hns_mdio_read - access phy register
* @bus: mdio bus
* @phy_id: phy id
* @regnum: register num
* @value: register value
*
* Return phy register value
*/
static int hns_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
{
int ret;
u16 reg_val = 0;
u8 devad = ((regnum >> 16) & 0x1f);
u8 is_c45 = !!(regnum & MII_ADDR_C45);
u16 reg = (u16)(regnum & 0xffff);
struct hns_mdio_device *mdio_dev = (struct hns_mdio_device *)bus->priv;
dev_dbg(&bus->dev, "mdio read %s,base is %p\n",
bus->id, mdio_dev->vbase);
dev_dbg(&bus->dev, "phy id=%d, is_c45=%d, devad=%d, reg=%#x!\n",
phy_id, is_c45, devad, reg);
/* Step 1: wait for ready */
ret = hns_mdio_wait_ready(bus);
if (ret) {
dev_err(&bus->dev, "MDIO bus is busy\n");
return ret;
}
if (!is_c45) {
hns_mdio_cmd_write(mdio_dev, is_c45,
MDIO_C22_READ, phy_id, reg);
} else {
MDIO_SET_REG_FIELD(mdio_dev, MDIO_ADDR_REG, MDIO_ADDR_DATA_M,
MDIO_ADDR_DATA_S, reg);
/* Step 2; config the cmd-reg to write addr*/
hns_mdio_cmd_write(mdio_dev, is_c45,
MDIO_C45_WRITE_ADDR, phy_id, devad);
/* Step 3: check for read or write opt is finished */
ret = hns_mdio_wait_ready(bus);
if (ret) {
dev_err(&bus->dev, "MDIO bus is busy\n");
return ret;
}
hns_mdio_cmd_write(mdio_dev, is_c45,
MDIO_C45_READ, phy_id, devad);
}
/* Step 5: waitting for MDIO_COMMAND_REG 's mdio_start==0,*/
/* check for read or write opt is finished */
ret = hns_mdio_wait_ready(bus);
if (ret) {
dev_err(&bus->dev, "MDIO bus is busy\n");
return ret;
}
reg_val = MDIO_GET_REG_BIT(mdio_dev, MDIO_STA_REG, MDIO_STATE_STA_B);
if (reg_val) {
dev_err(&bus->dev, " ERROR! MDIO Read failed!\n");
return -EBUSY;
}
/* Step 6; get out data*/
reg_val = (u16)MDIO_GET_REG_FIELD(mdio_dev, MDIO_RDATA_REG,
MDIO_RDATA_DATA_M, MDIO_RDATA_DATA_S);
return reg_val;
}
/**
* hns_mdio_reset - reset mdio bus
* @bus: mdio bus
*
* Return 0 on success, negative on failure
*/
static int hns_mdio_reset(struct mii_bus *bus)
{
struct hns_mdio_device *mdio_dev = (struct hns_mdio_device *)bus->priv;
const struct hns_mdio_sc_reg *sc_reg;
int ret;
if (dev_of_node(bus->parent)) {
if (!mdio_dev->subctrl_vbase) {
dev_err(&bus->dev, "mdio sys ctl reg has not maped\n");
return -ENODEV;
}
sc_reg = &mdio_dev->sc_reg;
/* 1. reset req, and read reset st check */
ret = mdio_sc_cfg_reg_write(mdio_dev, sc_reg->mdio_reset_req,
0x1, sc_reg->mdio_reset_st, 0x1,
MDIO_CHECK_SET_ST);
if (ret) {
dev_err(&bus->dev, "MDIO reset fail\n");
return ret;
}
/* 2. dis clk, and read clk st check */
ret = mdio_sc_cfg_reg_write(mdio_dev, sc_reg->mdio_clk_dis,
0x1, sc_reg->mdio_clk_st, 0x1,
MDIO_CHECK_CLR_ST);
if (ret) {
dev_err(&bus->dev, "MDIO dis clk fail\n");
return ret;
}
/* 3. reset dreq, and read reset st check */
ret = mdio_sc_cfg_reg_write(mdio_dev, sc_reg->mdio_reset_dreq,
0x1, sc_reg->mdio_reset_st, 0x1,
MDIO_CHECK_CLR_ST);
if (ret) {
dev_err(&bus->dev, "MDIO dis clk fail\n");
return ret;
}
/* 4. en clk, and read clk st check */
ret = mdio_sc_cfg_reg_write(mdio_dev, sc_reg->mdio_clk_en,
0x1, sc_reg->mdio_clk_st, 0x1,
MDIO_CHECK_SET_ST);
if (ret)
dev_err(&bus->dev, "MDIO en clk fail\n");
} else if (is_acpi_node(bus->parent->fwnode)) {
acpi_status s;
s = acpi_evaluate_object(ACPI_HANDLE(bus->parent),
"_RST", NULL, NULL);
if (ACPI_FAILURE(s)) {
dev_err(&bus->dev, "Reset failed, return:%#x\n", s);
ret = -EBUSY;
} else {
ret = 0;
}
} else {
dev_err(&bus->dev, "Can not get cfg data from DT or ACPI\n");
ret = -ENXIO;
}
return ret;
}
/**
* hns_mdio_probe - probe mdio device
* @pdev: mdio platform device
*
* Return 0 on success, negative on failure
*/
static int hns_mdio_probe(struct platform_device *pdev)
{
struct hns_mdio_device *mdio_dev;
struct mii_bus *new_bus;
struct resource *res;
int ret = -ENODEV;
if (!pdev) {
dev_err(NULL, "pdev is NULL!\r\n");
return -ENODEV;
}
mdio_dev = devm_kzalloc(&pdev->dev, sizeof(*mdio_dev), GFP_KERNEL);
if (!mdio_dev)
return -ENOMEM;
new_bus = devm_mdiobus_alloc(&pdev->dev);
if (!new_bus) {
dev_err(&pdev->dev, "mdiobus_alloc fail!\n");
return -ENOMEM;
}
new_bus->name = MDIO_BUS_NAME;
new_bus->read = hns_mdio_read;
new_bus->write = hns_mdio_write;
new_bus->reset = hns_mdio_reset;
new_bus->priv = mdio_dev;
new_bus->parent = &pdev->dev;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
mdio_dev->vbase = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(mdio_dev->vbase)) {
ret = PTR_ERR(mdio_dev->vbase);
return ret;
}
platform_set_drvdata(pdev, new_bus);
snprintf(new_bus->id, MII_BUS_ID_SIZE, "%s-%s", "Mii",
dev_name(&pdev->dev));
if (dev_of_node(&pdev->dev)) {
struct of_phandle_args reg_args;
ret = of_parse_phandle_with_fixed_args(pdev->dev.of_node,
"subctrl-vbase",
4,
0,
&reg_args);
if (!ret) {
mdio_dev->subctrl_vbase =
syscon_node_to_regmap(reg_args.np);
if (IS_ERR(mdio_dev->subctrl_vbase)) {
dev_warn(&pdev->dev, "syscon_node_to_regmap error\n");
mdio_dev->subctrl_vbase = NULL;
} else {
if (reg_args.args_count == 4) {
mdio_dev->sc_reg.mdio_clk_en =
(u16)reg_args.args[0];
mdio_dev->sc_reg.mdio_clk_dis =
(u16)reg_args.args[0] + 4;
mdio_dev->sc_reg.mdio_reset_req =
(u16)reg_args.args[1];
mdio_dev->sc_reg.mdio_reset_dreq =
(u16)reg_args.args[1] + 4;
mdio_dev->sc_reg.mdio_clk_st =
(u16)reg_args.args[2];
mdio_dev->sc_reg.mdio_reset_st =
(u16)reg_args.args[3];
} else {
/* for compatible */
mdio_dev->sc_reg.mdio_clk_en =
MDIO_SC_CLK_EN;
mdio_dev->sc_reg.mdio_clk_dis =
MDIO_SC_CLK_DIS;
mdio_dev->sc_reg.mdio_reset_req =
MDIO_SC_RESET_REQ;
mdio_dev->sc_reg.mdio_reset_dreq =
MDIO_SC_RESET_DREQ;
mdio_dev->sc_reg.mdio_clk_st =
MDIO_SC_CLK_ST;
mdio_dev->sc_reg.mdio_reset_st =
MDIO_SC_RESET_ST;
}
}
} else {
dev_warn(&pdev->dev, "find syscon ret = %#x\n", ret);
mdio_dev->subctrl_vbase = NULL;
}
ret = of_mdiobus_register(new_bus, pdev->dev.of_node);
} else if (is_acpi_node(pdev->dev.fwnode)) {
/* Clear all the IRQ properties */
memset(new_bus->irq, PHY_POLL, 4 * PHY_MAX_ADDR);
/* Mask out all PHYs from auto probing. */
new_bus->phy_mask = ~0;
/* Register the MDIO bus */
ret = mdiobus_register(new_bus);
} else {
dev_err(&pdev->dev, "Can not get cfg data from DT or ACPI\n");
ret = -ENXIO;
}
if (ret) {
dev_err(&pdev->dev, "Cannot register as MDIO bus!\n");
platform_set_drvdata(pdev, NULL);
return ret;
}
return 0;
}
/**
* hns_mdio_remove - remove mdio device
* @pdev: mdio platform device
*
* Return 0 on success, negative on failure
*/
static int hns_mdio_remove(struct platform_device *pdev)
{
struct mii_bus *bus;
bus = platform_get_drvdata(pdev);
mdiobus_unregister(bus);
platform_set_drvdata(pdev, NULL);
return 0;
}
static const struct of_device_id hns_mdio_match[] = {
{.compatible = "hisilicon,mdio"},
{.compatible = "hisilicon,hns-mdio"},
{}
};
MODULE_DEVICE_TABLE(of, hns_mdio_match);
static const struct acpi_device_id hns_mdio_acpi_match[] = {
{ "HISI0141", 0 },
{ },
};
MODULE_DEVICE_TABLE(acpi, hns_mdio_acpi_match);
static struct platform_driver hns_mdio_driver = {
.probe = hns_mdio_probe,
.remove = hns_mdio_remove,
.driver = {
.name = MDIO_DRV_NAME,
.of_match_table = hns_mdio_match,
.acpi_match_table = ACPI_PTR(hns_mdio_acpi_match),
},
};
module_platform_driver(hns_mdio_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Huawei Tech. Co., Ltd.");
MODULE_DESCRIPTION("Hisilicon HNS MDIO driver");
MODULE_ALIAS("platform:" MDIO_DRV_NAME);