mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-21 20:07:13 +07:00
bf91795e4a
This patch fix typos in Documentation/networking/dsa. Signed-off-by: Masanari Iida <standby24x7@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
115 lines
5.0 KiB
Plaintext
115 lines
5.0 KiB
Plaintext
Broadcom Starfighter 2 Ethernet switch driver
|
|
=============================================
|
|
|
|
Broadcom's Starfighter 2 Ethernet switch hardware block is commonly found and
|
|
deployed in the following products:
|
|
|
|
- xDSL gateways such as BCM63138
|
|
- streaming/multimedia Set Top Box such as BCM7445
|
|
- Cable Modem/residential gateways such as BCM7145/BCM3390
|
|
|
|
The switch is typically deployed in a configuration involving between 5 to 13
|
|
ports, offering a range of built-in and customizable interfaces:
|
|
|
|
- single integrated Gigabit PHY
|
|
- quad integrated Gigabit PHY
|
|
- quad external Gigabit PHY w/ MDIO multiplexer
|
|
- integrated MoCA PHY
|
|
- several external MII/RevMII/GMII/RGMII interfaces
|
|
|
|
The switch also supports specific congestion control features which allow MoCA
|
|
fail-over not to lose packets during a MoCA role re-election, as well as out of
|
|
band back-pressure to the host CPU network interface when downstream interfaces
|
|
are connected at a lower speed.
|
|
|
|
The switch hardware block is typically interfaced using MMIO accesses and
|
|
contains a bunch of sub-blocks/registers:
|
|
|
|
* SWITCH_CORE: common switch registers
|
|
* SWITCH_REG: external interfaces switch register
|
|
* SWITCH_MDIO: external MDIO bus controller (there is another one in SWITCH_CORE,
|
|
which is used for indirect PHY accesses)
|
|
* SWITCH_INDIR_RW: 64-bits wide register helper block
|
|
* SWITCH_INTRL2_0/1: Level-2 interrupt controllers
|
|
* SWITCH_ACB: Admission control block
|
|
* SWITCH_FCB: Fail-over control block
|
|
|
|
Implementation details
|
|
======================
|
|
|
|
The driver is located in drivers/net/dsa/bcm_sf2.c and is implemented as a DSA
|
|
driver; see Documentation/networking/dsa/dsa.txt for details on the subsystem
|
|
and what it provides.
|
|
|
|
The SF2 switch is configured to enable a Broadcom specific 4-bytes switch tag
|
|
which gets inserted by the switch for every packet forwarded to the CPU
|
|
interface, conversely, the CPU network interface should insert a similar tag for
|
|
packets entering the CPU port. The tag format is described in
|
|
net/dsa/tag_brcm.c.
|
|
|
|
Overall, the SF2 driver is a fairly regular DSA driver; there are a few
|
|
specifics covered below.
|
|
|
|
Device Tree probing
|
|
-------------------
|
|
|
|
The DSA platform device driver is probed using a specific compatible string
|
|
provided in net/dsa/dsa.c. The reason for that is because the DSA subsystem gets
|
|
registered as a platform device driver currently. DSA will provide the needed
|
|
device_node pointers which are then accessible by the switch driver setup
|
|
function to setup resources such as register ranges and interrupts. This
|
|
currently works very well because none of the of_* functions utilized by the
|
|
driver require a struct device to be bound to a struct device_node, but things
|
|
may change in the future.
|
|
|
|
MDIO indirect accesses
|
|
----------------------
|
|
|
|
Due to a limitation in how Broadcom switches have been designed, external
|
|
Broadcom switches connected to a SF2 require the use of the DSA slave MDIO bus
|
|
in order to properly configure them. By default, the SF2 pseudo-PHY address, and
|
|
an external switch pseudo-PHY address will both be snooping for incoming MDIO
|
|
transactions, since they are at the same address (30), resulting in some kind of
|
|
"double" programming. Using DSA, and setting ds->phys_mii_mask accordingly, we
|
|
selectively divert reads and writes towards external Broadcom switches
|
|
pseudo-PHY addresses. Newer revisions of the SF2 hardware have introduced a
|
|
configurable pseudo-PHY address which circumvents the initial design limitation.
|
|
|
|
Multimedia over CoAxial (MoCA) interfaces
|
|
-----------------------------------------
|
|
|
|
MoCA interfaces are fairly specific and require the use of a firmware blob which
|
|
gets loaded onto the MoCA processor(s) for packet processing. The switch
|
|
hardware contains logic which will assert/de-assert link states accordingly for
|
|
the MoCA interface whenever the MoCA coaxial cable gets disconnected or the
|
|
firmware gets reloaded. The SF2 driver relies on such events to properly set its
|
|
MoCA interface carrier state and properly report this to the networking stack.
|
|
|
|
The MoCA interfaces are supported using the PHY library's fixed PHY/emulated PHY
|
|
device and the switch driver registers a fixed_link_update callback for such
|
|
PHYs which reflects the link state obtained from the interrupt handler.
|
|
|
|
|
|
Power Management
|
|
----------------
|
|
|
|
Whenever possible, the SF2 driver tries to minimize the overall switch power
|
|
consumption by applying a combination of:
|
|
|
|
- turning off internal buffers/memories
|
|
- disabling packet processing logic
|
|
- putting integrated PHYs in IDDQ/low-power
|
|
- reducing the switch core clock based on the active port count
|
|
- enabling and advertising EEE
|
|
- turning off RGMII data processing logic when the link goes down
|
|
|
|
Wake-on-LAN
|
|
-----------
|
|
|
|
Wake-on-LAN is currently implemented by utilizing the host processor Ethernet
|
|
MAC controller wake-on logic. Whenever Wake-on-LAN is requested, an intersection
|
|
between the user request and the supported host Ethernet interface WoL
|
|
capabilities is done and the intersection result gets configured. During
|
|
system-wide suspend/resume, only ports not participating in Wake-on-LAN are
|
|
disabled.
|