linux_dsm_epyc7002/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
Archit Taneja 28546b0955 arm64: dts: apq8016-sbc: Add HDMI display support
The APQ8016-sbc provides a HDMI output. The APQ8016 display block only
provides a MIPI DSI output. So, the board has a ADV7533 DSI to HDMI
encoder chip that sits between the DSI PHY output and the HDMI
connector.

Add the ADV7533 DT node under its I2C control bus, and tie the DSI
output port to the ADV7533's input port.

Cc: Andy Gross <andy.gross@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
2016-08-26 15:31:51 -05:00

400 lines
7.7 KiB
Plaintext

/*
* Copyright (c) 2015, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include "msm8916.dtsi"
#include "pm8916.dtsi"
#include "apq8016-sbc-soc-pins.dtsi"
#include "apq8016-sbc-pmic-pins.dtsi"
/ {
aliases {
serial0 = &blsp1_uart2;
serial1 = &blsp1_uart1;
usid0 = &pm8916_0;
i2c0 = &blsp_i2c2;
i2c1 = &blsp_i2c6;
i2c3 = &blsp_i2c4;
spi0 = &blsp_spi5;
spi1 = &blsp_spi3;
};
chosen {
stdout-path = "serial0";
};
soc {
dma@7884000 {
status = "okay";
};
serial@78af000 {
label = "LS-UART0";
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart1_default>;
pinctrl-1 = <&blsp1_uart1_sleep>;
};
serial@78b0000 {
label = "LS-UART1";
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart2_default>;
pinctrl-1 = <&blsp1_uart2_sleep>;
};
i2c@78b6000 {
/* On Low speed expansion */
label = "LS-I2C0";
status = "okay";
};
i2c@78b8000 {
/* On High speed expansion */
label = "HS-I2C2";
status = "okay";
adv_bridge: bridge@39 {
status = "okay";
compatible = "adi,adv7533";
reg = <0x39>;
interrupt-parent = <&msmgpio>;
interrupts = <31 2>;
adi,dsi-lanes = <4>;
pd-gpios = <&msmgpio 32 0>;
avdd-supply = <&pm8916_l6>;
v1p2-supply = <&pm8916_l6>;
v3p3-supply = <&pm8916_l17>;
pinctrl-names = "default","sleep";
pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7533_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
port@1 {
reg = <1>;
adv7533_out: endpoint {
remote-endpoint = <&hdmi_con>;
};
};
};
};
};
i2c@78ba000 {
/* On Low speed expansion */
label = "LS-I2C1";
status = "okay";
};
spi@78b7000 {
/* On High speed expansion */
label = "HS-SPI1";
status = "okay";
};
spi@78b9000 {
/* On Low speed expansion */
label = "LS-SPI0";
status = "okay";
};
leds {
pinctrl-names = "default";
pinctrl-0 = <&msmgpio_leds>,
<&pm8916_gpios_leds>,
<&pm8916_mpps_leds>;
compatible = "gpio-leds";
led@1 {
label = "apq8016-sbc:green:user1";
gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
led@2 {
label = "apq8016-sbc:green:user2";
gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
default-state = "off";
};
led@3 {
label = "apq8016-sbc:green:user3";
gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc1";
default-state = "off";
};
led@4 {
label = "apq8016-sbc:green:user4";
gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "none";
default-state = "off";
};
led@5 {
label = "apq8016-sbc:yellow:wlan";
gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "wlan";
default-state = "off";
};
led@6 {
label = "apq8016-sbc:blue:bt";
gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bt";
default-state = "off";
};
};
sdhci@07824000 {
vmmc-supply = <&pm8916_l8>;
vqmmc-supply = <&pm8916_l5>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
status = "okay";
};
sdhci@07864000 {
vmmc-supply = <&pm8916_l11>;
vqmmc-supply = <&pm8916_l12>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
cd-gpios = <&msmgpio 38 0x1>;
status = "okay";
};
usb@78d9000 {
extcon = <&usb_id>, <&usb_id>;
status = "okay";
};
ehci@78d9000 {
status = "okay";
};
phy@78d9000 {
v1p8-supply = <&pm8916_l7>;
v3p3-supply = <&pm8916_l13>;
vddcx-supply = <&pm8916_s1>;
extcon = <&usb_id>, <&usb_id>;
dr_mode = "otg";
status = "okay";
switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb_sw_sel_pm>;
};
lpass@07708000 {
status = "okay";
};
mdss@1a00000 {
status = "okay";
mdp@1a01000 {
status = "okay";
};
dsi@1a98000 {
status = "okay";
vdda-supply = <&pm8916_l2>;
vddio-supply = <&pm8916_l6>;
ports {
port@1 {
endpoint {
remote-endpoint = <&adv7533_in>;
data-lanes = <0 1 2 3>;
};
};
};
};
dsi-phy@1a98300 {
status = "okay";
vddio-supply = <&pm8916_l6>;
};
};
};
usb2513 {
compatible = "smsc,usb3503";
reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
initial-mode = <1>;
};
usb_id: usb-id {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb_id_default>;
};
hdmi-out {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con: endpoint {
remote-endpoint = <&adv7533_out>;
};
};
};
};
&smd_rpm_regulators {
vdd_l1_l2_l3-supply = <&pm8916_s3>;
vdd_l5-supply = <&pm8916_s3>;
vdd_l4_l5_l6-supply = <&pm8916_s4>;
vdd_l7-supply = <&pm8916_s4>;
s1 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1562000>;
};
s3 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1562000>;
};
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
l1 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1525000>;
};
l2 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1525000>;
};
l3 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1525000>;
};
l4 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l5 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l6 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l7 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l8 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l9 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l10 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l11 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l12 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l13 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l14 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
/**
* 1.8v required on LS expansion
* for mezzanine boards
*/
l15 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
regulator-always-on;
};
l16 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l17 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l18 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
};