mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
23a71fd616
This patchset attempts to standardize the naming of dt-bindings documents based on the Broadcom vendor prefix of brcm. Although there are no guidelines currently present for how to name the dt-bindings document the "vendor,binding.txt" style is in use by some of the other vendors. Acked-by: Lee Jones <lee@kernel.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Rob Herring <robh@kernel.org>
53 lines
2.1 KiB
Plaintext
53 lines
2.1 KiB
Plaintext
Broadcom Kona Family GPIO
|
|
=========================
|
|
|
|
This GPIO driver is used in the following Broadcom SoCs:
|
|
BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
|
|
|
|
The Broadcom GPIO Controller IP can be configured prior to synthesis to
|
|
support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
|
|
GPIO controller only supports edge, not level, triggering of interrupts.
|
|
|
|
Required properties
|
|
-------------------
|
|
|
|
- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio"
|
|
- reg: Physical base address and length of the controller's registers.
|
|
- interrupts: The interrupt outputs from the controller. There is one GPIO
|
|
interrupt per GPIO bank. The number of interrupts listed depends on the
|
|
number of GPIO banks on the SoC. The interrupts must be ordered by bank,
|
|
starting with bank 0. There is always a 1:1 mapping between banks and
|
|
IRQs.
|
|
- #gpio-cells: Should be <2>. The first cell is the pin number, the second
|
|
cell is used to specify optional parameters:
|
|
- bit 0 specifies polarity (0 for normal, 1 for inverted)
|
|
See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
|
|
- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The
|
|
second cell is used to specify flags. The following subset of flags is
|
|
supported:
|
|
- trigger type (bits[1:0]):
|
|
1 = low-to-high edge triggered.
|
|
2 = high-to-low edge triggered.
|
|
3 = low-to-high or high-to-low edge triggered
|
|
Valid values are 1, 2, 3
|
|
See also .../devicetree/bindings/interrupt-controller/interrupts.txt.
|
|
- gpio-controller: Marks the device node as a GPIO controller.
|
|
- interrupt-controller: Marks the device node as an interrupt controller.
|
|
|
|
Example:
|
|
gpio: gpio@35003000 {
|
|
compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
|
|
reg = <0x35003000 0x800>;
|
|
interrupts =
|
|
<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
|
|
GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
|
|
GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
|
|
GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
|
|
GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
|
|
GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
|
|
#gpio-cells = <2>;
|
|
#interrupt-cells = <2>;
|
|
gpio-controller;
|
|
interrupt-controller;
|
|
};
|