linux_dsm_epyc7002/include/linux/platform_data/mtd-davinci.h
Bartosz Golaszewski bde1a3d846 mtd: rawnand: davinci: store the core chipselect number in platform data
We have the 'ti,davinci-chipselect' property in the device tree, but
when using platform data the driver silently uses the id field of
struct platform_device as the chipselect. This is confusing and we
almost broke the nand support again recently after converting the
platform to common clock framework (which changed the device id in the
clock lookup - the problem is gone now that we no longer acquire the
clock in the nand driver.

This patch adds a new field - core_chipsel - to the platform_data.
Subsequent patches will convert the platforms to using this new field.

Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2018-05-02 14:58:30 +05:30

101 lines
2.9 KiB
C

/*
* mach-davinci/nand.h
*
* Copyright © 2006 Texas Instruments.
*
* Ported to 2.6.23 Copyright © 2008 by
* Sander Huijsen <Shuijsen@optelecom-nkf.com>
* Troy Kisky <troy.kisky@boundarydevices.com>
* Dirk Behme <Dirk.Behme@gmail.com>
*
* --------------------------------------------------------------------------
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#ifndef __ARCH_ARM_DAVINCI_NAND_H
#define __ARCH_ARM_DAVINCI_NAND_H
#include <linux/mtd/rawnand.h>
#define NANDFCR_OFFSET 0x60
#define NANDFSR_OFFSET 0x64
#define NANDF1ECC_OFFSET 0x70
/* 4-bit ECC syndrome registers */
#define NAND_4BIT_ECC_LOAD_OFFSET 0xbc
#define NAND_4BIT_ECC1_OFFSET 0xc0
#define NAND_4BIT_ECC2_OFFSET 0xc4
#define NAND_4BIT_ECC3_OFFSET 0xc8
#define NAND_4BIT_ECC4_OFFSET 0xcc
#define NAND_ERR_ADD1_OFFSET 0xd0
#define NAND_ERR_ADD2_OFFSET 0xd4
#define NAND_ERR_ERRVAL1_OFFSET 0xd8
#define NAND_ERR_ERRVAL2_OFFSET 0xdc
/* NOTE: boards don't need to use these address bits
* for ALE/CLE unless they support booting from NAND.
* They're used unless platform data overrides them.
*/
#define MASK_ALE 0x08
#define MASK_CLE 0x10
struct davinci_nand_pdata { /* platform_data */
uint32_t mask_ale;
uint32_t mask_cle;
/*
* 0-indexed chip-select number of the asynchronous
* interface to which the NAND device has been connected.
*
* So, if you have NAND connected to CS3 of DA850, you
* will pass '1' here. Since the asynchronous interface
* on DA850 starts from CS2.
*/
uint32_t core_chipsel;
/* for packages using two chipselects */
uint32_t mask_chipsel;
/* board's default static partition info */
struct mtd_partition *parts;
unsigned nr_parts;
/* none == NAND_ECC_NONE (strongly *not* advised!!)
* soft == NAND_ECC_SOFT
* else == NAND_ECC_HW, according to ecc_bits
*
* All DaVinci-family chips support 1-bit hardware ECC.
* Newer ones also support 4-bit ECC, but are awkward
* using it with large page chips.
*/
nand_ecc_modes_t ecc_mode;
u8 ecc_bits;
/* e.g. NAND_BUSWIDTH_16 */
unsigned options;
/* e.g. NAND_BBT_USE_FLASH */
unsigned bbt_options;
/* Main and mirror bbt descriptor overrides */
struct nand_bbt_descr *bbt_td;
struct nand_bbt_descr *bbt_md;
/* Access timings */
struct davinci_aemif_timing *timing;
};
#endif /* __ARCH_ARM_DAVINCI_NAND_H */