mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-24 02:18:18 +07:00
f2fb18c7cc
Earlier attempt to move am335x mcasp to probe with ti-sysc
interconnect target module caused audio to stop working and and
the dts changes were reverted by commit 5d2632a577 ("ARM: dts:
Revert am335x mcasp ti-sysc changes").
Turns out we were missing the l3 data port ranges for mcasp. This
caused mcasp dma to attempt to use wrong port address. So let's
try again essentially reverting the earlier revert and adding the
missing l3 data port ranges.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
448 lines
10 KiB
Plaintext
448 lines
10 KiB
Plaintext
/*
|
|
* Device Tree Source for AM33XX SoC
|
|
*
|
|
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public License
|
|
* version 2. This program is licensed "as is" without any warranty of any
|
|
* kind, whether express or implied.
|
|
*/
|
|
|
|
#include <dt-bindings/bus/ti-sysc.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/am33xx.h>
|
|
#include <dt-bindings/clock/am3.h>
|
|
|
|
/ {
|
|
compatible = "ti,am33xx";
|
|
interrupt-parent = <&intc>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
chosen { };
|
|
|
|
aliases {
|
|
i2c0 = &i2c0;
|
|
i2c1 = &i2c1;
|
|
i2c2 = &i2c2;
|
|
serial0 = &uart0;
|
|
serial1 = &uart1;
|
|
serial2 = &uart2;
|
|
serial3 = &uart3;
|
|
serial4 = &uart4;
|
|
serial5 = &uart5;
|
|
d-can0 = &dcan0;
|
|
d-can1 = &dcan1;
|
|
usb0 = &usb0;
|
|
usb1 = &usb1;
|
|
phy0 = &usb0_phy;
|
|
phy1 = &usb1_phy;
|
|
ethernet0 = &cpsw_emac0;
|
|
ethernet1 = &cpsw_emac1;
|
|
spi0 = &spi0;
|
|
spi1 = &spi1;
|
|
};
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
cpu@0 {
|
|
compatible = "arm,cortex-a8";
|
|
device_type = "cpu";
|
|
reg = <0>;
|
|
|
|
operating-points-v2 = <&cpu0_opp_table>;
|
|
|
|
clocks = <&dpll_mpu_ck>;
|
|
clock-names = "cpu";
|
|
|
|
clock-latency = <300000>; /* From omap-cpufreq driver */
|
|
};
|
|
};
|
|
|
|
cpu0_opp_table: opp-table {
|
|
compatible = "operating-points-v2-ti-cpu";
|
|
syscon = <&scm_conf>;
|
|
|
|
/*
|
|
* The three following nodes are marked with opp-suspend
|
|
* because the can not be enabled simultaneously on a
|
|
* single SoC.
|
|
*/
|
|
opp50-300000000 {
|
|
opp-hz = /bits/ 64 <300000000>;
|
|
opp-microvolt = <950000 931000 969000>;
|
|
opp-supported-hw = <0x06 0x0010>;
|
|
opp-suspend;
|
|
};
|
|
|
|
opp100-275000000 {
|
|
opp-hz = /bits/ 64 <275000000>;
|
|
opp-microvolt = <1100000 1078000 1122000>;
|
|
opp-supported-hw = <0x01 0x00FF>;
|
|
opp-suspend;
|
|
};
|
|
|
|
opp100-300000000 {
|
|
opp-hz = /bits/ 64 <300000000>;
|
|
opp-microvolt = <1100000 1078000 1122000>;
|
|
opp-supported-hw = <0x06 0x0020>;
|
|
opp-suspend;
|
|
};
|
|
|
|
opp100-500000000 {
|
|
opp-hz = /bits/ 64 <500000000>;
|
|
opp-microvolt = <1100000 1078000 1122000>;
|
|
opp-supported-hw = <0x01 0xFFFF>;
|
|
};
|
|
|
|
opp100-600000000 {
|
|
opp-hz = /bits/ 64 <600000000>;
|
|
opp-microvolt = <1100000 1078000 1122000>;
|
|
opp-supported-hw = <0x06 0x0040>;
|
|
};
|
|
|
|
opp120-600000000 {
|
|
opp-hz = /bits/ 64 <600000000>;
|
|
opp-microvolt = <1200000 1176000 1224000>;
|
|
opp-supported-hw = <0x01 0xFFFF>;
|
|
};
|
|
|
|
opp120-720000000 {
|
|
opp-hz = /bits/ 64 <720000000>;
|
|
opp-microvolt = <1200000 1176000 1224000>;
|
|
opp-supported-hw = <0x06 0x0080>;
|
|
};
|
|
|
|
oppturbo-720000000 {
|
|
opp-hz = /bits/ 64 <720000000>;
|
|
opp-microvolt = <1260000 1234800 1285200>;
|
|
opp-supported-hw = <0x01 0xFFFF>;
|
|
};
|
|
|
|
oppturbo-800000000 {
|
|
opp-hz = /bits/ 64 <800000000>;
|
|
opp-microvolt = <1260000 1234800 1285200>;
|
|
opp-supported-hw = <0x06 0x0100>;
|
|
};
|
|
|
|
oppnitro-1000000000 {
|
|
opp-hz = /bits/ 64 <1000000000>;
|
|
opp-microvolt = <1325000 1298500 1351500>;
|
|
opp-supported-hw = <0x04 0x0200>;
|
|
};
|
|
};
|
|
|
|
pmu@4b000000 {
|
|
compatible = "arm,cortex-a8-pmu";
|
|
interrupts = <3>;
|
|
reg = <0x4b000000 0x1000000>;
|
|
ti,hwmods = "debugss";
|
|
};
|
|
|
|
/*
|
|
* The soc node represents the soc top level view. It is used for IPs
|
|
* that are not memory mapped in the MPU view or for the MPU itself.
|
|
*/
|
|
soc {
|
|
compatible = "ti,omap-infra";
|
|
mpu {
|
|
compatible = "ti,omap3-mpu";
|
|
ti,hwmods = "mpu";
|
|
pm-sram = <&pm_sram_code
|
|
&pm_sram_data>;
|
|
};
|
|
};
|
|
|
|
/*
|
|
* XXX: Use a flat representation of the AM33XX interconnect.
|
|
* The real AM33XX interconnect network is quite complex. Since
|
|
* it will not bring real advantage to represent that in DT
|
|
* for the moment, just use a fake OCP bus entry to represent
|
|
* the whole bus hierarchy.
|
|
*/
|
|
ocp {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
ti,hwmods = "l3_main";
|
|
|
|
l4_wkup: interconnect@44c00000 {
|
|
wkup_m3: wkup_m3@100000 {
|
|
compatible = "ti,am3352-wkup-m3";
|
|
reg = <0x100000 0x4000>,
|
|
<0x180000 0x2000>;
|
|
reg-names = "umem", "dmem";
|
|
ti,hwmods = "wkup_m3";
|
|
ti,pm-firmware = "am335x-pm-firmware.elf";
|
|
};
|
|
};
|
|
l4_per: interconnect@48000000 {
|
|
};
|
|
l4_fw: interconnect@47c00000 {
|
|
};
|
|
l4_fast: interconnect@4a000000 {
|
|
};
|
|
l4_mpuss: interconnect@4b140000 {
|
|
};
|
|
|
|
intc: interrupt-controller@48200000 {
|
|
compatible = "ti,am33xx-intc";
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
reg = <0x48200000 0x1000>;
|
|
};
|
|
|
|
edma: edma@49000000 {
|
|
compatible = "ti,edma3-tpcc";
|
|
ti,hwmods = "tpcc";
|
|
reg = <0x49000000 0x10000>;
|
|
reg-names = "edma3_cc";
|
|
interrupts = <12 13 14>;
|
|
interrupt-names = "edma3_ccint", "edma3_mperr",
|
|
"edma3_ccerrint";
|
|
dma-requests = <64>;
|
|
#dma-cells = <2>;
|
|
|
|
ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
|
|
<&edma_tptc2 0>;
|
|
|
|
ti,edma-memcpy-channels = <20 21>;
|
|
};
|
|
|
|
edma_tptc0: tptc@49800000 {
|
|
compatible = "ti,edma3-tptc";
|
|
ti,hwmods = "tptc0";
|
|
reg = <0x49800000 0x100000>;
|
|
interrupts = <112>;
|
|
interrupt-names = "edma3_tcerrint";
|
|
};
|
|
|
|
edma_tptc1: tptc@49900000 {
|
|
compatible = "ti,edma3-tptc";
|
|
ti,hwmods = "tptc1";
|
|
reg = <0x49900000 0x100000>;
|
|
interrupts = <113>;
|
|
interrupt-names = "edma3_tcerrint";
|
|
};
|
|
|
|
edma_tptc2: tptc@49a00000 {
|
|
compatible = "ti,edma3-tptc";
|
|
ti,hwmods = "tptc2";
|
|
reg = <0x49a00000 0x100000>;
|
|
interrupts = <114>;
|
|
interrupt-names = "edma3_tcerrint";
|
|
};
|
|
|
|
mmc3: mmc@47810000 {
|
|
compatible = "ti,omap4-hsmmc";
|
|
ti,hwmods = "mmc3";
|
|
ti,needs-special-reset;
|
|
interrupts = <29>;
|
|
reg = <0x47810000 0x1000>;
|
|
status = "disabled";
|
|
};
|
|
|
|
usb: usb@47400000 {
|
|
compatible = "ti,am33xx-usb";
|
|
reg = <0x47400000 0x1000>;
|
|
ranges;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ti,hwmods = "usb_otg_hs";
|
|
status = "disabled";
|
|
|
|
usb_ctrl_mod: control@44e10620 {
|
|
compatible = "ti,am335x-usb-ctrl-module";
|
|
reg = <0x44e10620 0x10
|
|
0x44e10648 0x4>;
|
|
reg-names = "phy_ctrl", "wakeup";
|
|
status = "disabled";
|
|
};
|
|
|
|
usb0_phy: usb-phy@47401300 {
|
|
compatible = "ti,am335x-usb-phy";
|
|
reg = <0x47401300 0x100>;
|
|
reg-names = "phy";
|
|
status = "disabled";
|
|
ti,ctrl_mod = <&usb_ctrl_mod>;
|
|
#phy-cells = <0>;
|
|
};
|
|
|
|
usb0: usb@47401000 {
|
|
compatible = "ti,musb-am33xx";
|
|
status = "disabled";
|
|
reg = <0x47401400 0x400
|
|
0x47401000 0x200>;
|
|
reg-names = "mc", "control";
|
|
|
|
interrupts = <18>;
|
|
interrupt-names = "mc";
|
|
dr_mode = "otg";
|
|
mentor,multipoint = <1>;
|
|
mentor,num-eps = <16>;
|
|
mentor,ram-bits = <12>;
|
|
mentor,power = <500>;
|
|
phys = <&usb0_phy>;
|
|
|
|
dmas = <&cppi41dma 0 0 &cppi41dma 1 0
|
|
&cppi41dma 2 0 &cppi41dma 3 0
|
|
&cppi41dma 4 0 &cppi41dma 5 0
|
|
&cppi41dma 6 0 &cppi41dma 7 0
|
|
&cppi41dma 8 0 &cppi41dma 9 0
|
|
&cppi41dma 10 0 &cppi41dma 11 0
|
|
&cppi41dma 12 0 &cppi41dma 13 0
|
|
&cppi41dma 14 0 &cppi41dma 0 1
|
|
&cppi41dma 1 1 &cppi41dma 2 1
|
|
&cppi41dma 3 1 &cppi41dma 4 1
|
|
&cppi41dma 5 1 &cppi41dma 6 1
|
|
&cppi41dma 7 1 &cppi41dma 8 1
|
|
&cppi41dma 9 1 &cppi41dma 10 1
|
|
&cppi41dma 11 1 &cppi41dma 12 1
|
|
&cppi41dma 13 1 &cppi41dma 14 1>;
|
|
dma-names =
|
|
"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
|
|
"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
|
|
"rx14", "rx15",
|
|
"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
|
|
"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
|
|
"tx14", "tx15";
|
|
};
|
|
|
|
usb1_phy: usb-phy@47401b00 {
|
|
compatible = "ti,am335x-usb-phy";
|
|
reg = <0x47401b00 0x100>;
|
|
reg-names = "phy";
|
|
status = "disabled";
|
|
ti,ctrl_mod = <&usb_ctrl_mod>;
|
|
#phy-cells = <0>;
|
|
};
|
|
|
|
usb1: usb@47401800 {
|
|
compatible = "ti,musb-am33xx";
|
|
status = "disabled";
|
|
reg = <0x47401c00 0x400
|
|
0x47401800 0x200>;
|
|
reg-names = "mc", "control";
|
|
interrupts = <19>;
|
|
interrupt-names = "mc";
|
|
dr_mode = "otg";
|
|
mentor,multipoint = <1>;
|
|
mentor,num-eps = <16>;
|
|
mentor,ram-bits = <12>;
|
|
mentor,power = <500>;
|
|
phys = <&usb1_phy>;
|
|
|
|
dmas = <&cppi41dma 15 0 &cppi41dma 16 0
|
|
&cppi41dma 17 0 &cppi41dma 18 0
|
|
&cppi41dma 19 0 &cppi41dma 20 0
|
|
&cppi41dma 21 0 &cppi41dma 22 0
|
|
&cppi41dma 23 0 &cppi41dma 24 0
|
|
&cppi41dma 25 0 &cppi41dma 26 0
|
|
&cppi41dma 27 0 &cppi41dma 28 0
|
|
&cppi41dma 29 0 &cppi41dma 15 1
|
|
&cppi41dma 16 1 &cppi41dma 17 1
|
|
&cppi41dma 18 1 &cppi41dma 19 1
|
|
&cppi41dma 20 1 &cppi41dma 21 1
|
|
&cppi41dma 22 1 &cppi41dma 23 1
|
|
&cppi41dma 24 1 &cppi41dma 25 1
|
|
&cppi41dma 26 1 &cppi41dma 27 1
|
|
&cppi41dma 28 1 &cppi41dma 29 1>;
|
|
dma-names =
|
|
"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
|
|
"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
|
|
"rx14", "rx15",
|
|
"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
|
|
"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
|
|
"tx14", "tx15";
|
|
};
|
|
|
|
cppi41dma: dma-controller@47402000 {
|
|
compatible = "ti,am3359-cppi41";
|
|
reg = <0x47400000 0x1000
|
|
0x47402000 0x1000
|
|
0x47403000 0x1000
|
|
0x47404000 0x4000>;
|
|
reg-names = "glue", "controller", "scheduler", "queuemgr";
|
|
interrupts = <17>;
|
|
interrupt-names = "glue";
|
|
#dma-cells = <2>;
|
|
#dma-channels = <30>;
|
|
#dma-requests = <256>;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
ocmcram: ocmcram@40300000 {
|
|
compatible = "mmio-sram";
|
|
reg = <0x40300000 0x10000>; /* 64k */
|
|
ranges = <0x0 0x40300000 0x10000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
pm_sram_code: pm-sram-code@0 {
|
|
compatible = "ti,sram";
|
|
reg = <0x0 0x1000>;
|
|
protect-exec;
|
|
};
|
|
|
|
pm_sram_data: pm-sram-data@1000 {
|
|
compatible = "ti,sram";
|
|
reg = <0x1000 0x1000>;
|
|
pool;
|
|
};
|
|
};
|
|
|
|
emif: emif@4c000000 {
|
|
compatible = "ti,emif-am3352";
|
|
reg = <0x4c000000 0x1000000>;
|
|
ti,hwmods = "emif";
|
|
interrupts = <101>;
|
|
sram = <&pm_sram_code
|
|
&pm_sram_data>;
|
|
ti,no-idle;
|
|
};
|
|
|
|
gpmc: gpmc@50000000 {
|
|
compatible = "ti,am3352-gpmc";
|
|
ti,hwmods = "gpmc";
|
|
ti,no-idle-on-init;
|
|
reg = <0x50000000 0x2000>;
|
|
interrupts = <100>;
|
|
dmas = <&edma 52 0>;
|
|
dma-names = "rxtx";
|
|
gpmc,num-cs = <7>;
|
|
gpmc,num-waitpins = <2>;
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
status = "disabled";
|
|
};
|
|
|
|
sham: sham@53100000 {
|
|
compatible = "ti,omap4-sham";
|
|
ti,hwmods = "sham";
|
|
reg = <0x53100000 0x200>;
|
|
interrupts = <109>;
|
|
dmas = <&edma 36 0>;
|
|
dma-names = "rx";
|
|
};
|
|
|
|
aes: aes@53500000 {
|
|
compatible = "ti,omap4-aes";
|
|
ti,hwmods = "aes";
|
|
reg = <0x53500000 0xa0>;
|
|
interrupts = <103>;
|
|
dmas = <&edma 6 0>,
|
|
<&edma 5 0>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
};
|
|
};
|
|
|
|
#include "am33xx-l4.dtsi"
|
|
#include "am33xx-clocks.dtsi"
|