mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-21 00:08:17 +07:00
206c12fc48
for 4.17, please pull the following: - Henry fixes the pin functions for the JTAG pins, nothing uses this for now, but it could be backported eventually if deemed appropriate - Stefan fixes the register ranges for the bcm2835-i2s nodes in the binding document definition, he then fixes the probing of the bcm2835-i2s driver by providing an appropriate register range and a missing clock. Stefan also makes sure that the appropriate pull settings are applied to the pins used on the Raspberry Pi Zero Wireless, he then adds the necessary UART node to connected to the BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB OTG mode on the Pi Zero W since he became usable again - Baruch adds the necessary Device Tree nodes to support the Raspberry Pi GPIO expander which is controlled via the VC4 firmware - Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router - Eric adds the DPI hardware block into the BCM283x Device Tree include file for future use when an actual panel is available - Florian updates the Northstar Plus platforms to use port 8 of the internal switch as the CPU/management port since necessary code was added in the b53 switch driver to support that -----BEGIN PGP SIGNATURE----- iQIcBAABCAAGBQJaqCvCAAoJEIfQlpxEBwcE7MIP/iMbvwen6G+JAk2yeeuOgZVi +B2GLuOEcyi+MEQQgghpggjMehTPGTklXCNhNIziGYvpreGyzvGAmq/up+hFFVJ7 TNU0nslf8hBURdexx23/rkJBJFx8jv/R8au1PUZhEHLONQs38UBOe1umWbKDvpxn qp+KvBF3EUdqVfnBcdagImr0MfVKlLpGjTuyfPfHhfs1R8egzY/fY/PUMBw4GFHB alMrENKR3mFYl+cTk7Ox4yP9WYY4eZnrwuu43J0JHk6+r1De387MyWy+irNHKfKz alux92DUDXMYxG57cEREfd9YzI0BOiU3orMBIkRACDpnI7bYWebviDKPda20dDli 4VgILTj1Vbi2/Qn+0PAWpqBZCVugnFNX44hfSZ1oVHjPlUVoDLojxcAG5AskmNVV InMtROagSwgujK7PZD7knc4O73ihdoaLqp1dN0KLn+xx8x17wiVQUAWq2l5XpGD4 o+rarZRjAmIVe+xzvZfgmMRTaJRwmRNHgcWDWMKSACV63xmRxa9F9BM+Dep4zMq5 BON6Hvu9SMfgycgHWpU3GGKfAljRm8aRWzKRspIi+whqUuIhxCZcSyMlonrocv5b O1AGm5f8Exdm9/4TTSzF7leVne0CXhIyfwEmtp42+y403OGONIaRqspe1on6nr7P Yvdn0jO5CauPr7iM6Z10 =SKgx -----END PGP SIGNATURE----- Merge tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux into next/dt Pull "Broadcom devicetree changes for 4.17" from Florian Fainelli: This pull request contains Broadcom ARM-based SoCs devicetree changes for 4.17, please pull the following: - Henry fixes the pin functions for the JTAG pins, nothing uses this for now, but it could be backported eventually if deemed appropriate - Stefan fixes the register ranges for the bcm2835-i2s nodes in the binding document definition, he then fixes the probing of the bcm2835-i2s driver by providing an appropriate register range and a missing clock. Stefan also makes sure that the appropriate pull settings are applied to the pins used on the Raspberry Pi Zero Wireless, he then adds the necessary UART node to connected to the BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB OTG mode on the Pi Zero W since he became usable again - Baruch adds the necessary Device Tree nodes to support the Raspberry Pi GPIO expander which is controlled via the VC4 firmware - Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router - Eric adds the DPI hardware block into the BCM283x Device Tree include file for future use when an actual panel is available - Florian updates the Northstar Plus platforms to use port 8 of the internal switch as the CPU/management port since necessary code was added in the b53 switch driver to support that * tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux: ARM: dts: NSP: Switch to port 8 for CPU port ARM: bcm2835: Add the DPI hardware to the device tree. ARM: dts: BCM5301X: add missing LEDs for Buffalo WZR-900DHP ARM: dts: bcm2835-rpi-zero-w: Enable OTG mode ARM: dts: bcm2835-rpi-zero-w: Add bcm43438 serial slave ARM: dts: bcm283x: Apply pull settings to Zero W relevant groups ARM: dts: bcm2837-rpi-3-b: add GPIO expander ARM: dts: bcm2835: make the firmware node into a bus ARM: dts: bcm283x: Fix probing of bcm2835-i2s dt-bindings: bcm283x: Fix register ranges of bcm2835-i2s ARM: dts: bcm283x: Fix pin function of JTAG pins |
||
|---|---|---|
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| firmware | ||
| fs | ||
| include | ||
| init | ||
| ipc | ||
| kernel | ||
| lib | ||
| LICENSES | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .cocciconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Linux kernel ============ This file was moved to Documentation/admin-guide/README.rst Please notice that there are several guides for kernel developers and users. These guides can be rendered in a number of formats, like HTML and PDF. In order to build the documentation, use ``make htmldocs`` or ``make pdfdocs``. There are various text files in the Documentation/ subdirectory, several of them using the Restructured Text markup notation. See Documentation/00-INDEX for a list of what is contained in each file. Please read the Documentation/process/changes.rst file, as it contains the requirements for building and running the kernel, and information about the problems which may result by upgrading your kernel.