mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
6f357de854
Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs,
as well as the hardware BCH controller, used by the jz4780_{nand,bch}
drivers.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
87 lines
2.5 KiB
Plaintext
87 lines
2.5 KiB
Plaintext
* Ingenic JZ4780 NAND/BCH
|
|
|
|
This file documents the device tree bindings for NAND flash devices on the
|
|
JZ4780. NAND devices are connected to the NEMC controller (described in
|
|
memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
|
|
be children of the NEMC node.
|
|
|
|
Required NAND controller device properties:
|
|
- compatible: Should be set to "ingenic,jz4780-nand".
|
|
- reg: For each bank with a NAND chip attached, should specify a bank number,
|
|
an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
|
|
|
|
Optional NAND controller device properties:
|
|
- ingenic,bch-controller: To make use of the hardware BCH controller, this
|
|
property must contain a phandle for the BCH controller node. The required
|
|
properties for this node are described below. If this is not specified,
|
|
software BCH will be used instead.
|
|
|
|
Optional children nodes:
|
|
- Individual NAND chips are children of the NAND controller node.
|
|
|
|
Required children node properties:
|
|
- reg: An integer ranging from 1 to 6 representing the CS line to use.
|
|
|
|
Optional children node properties:
|
|
- nand-ecc-step-size: ECC block size in bytes.
|
|
- nand-ecc-strength: ECC strength (max number of correctable bits).
|
|
- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default
|
|
- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false
|
|
- rb-gpios: GPIO specifier for the busy pin.
|
|
- wp-gpios: GPIO specifier for the write protect pin.
|
|
|
|
Optional child node of NAND chip nodes:
|
|
- partitions: see Documentation/devicetree/bindings/mtd/partition.txt
|
|
|
|
Example:
|
|
|
|
nemc: nemc@13410000 {
|
|
...
|
|
|
|
nandc: nand-controller@1 {
|
|
compatible = "ingenic,jz4780-nand";
|
|
reg = <1 0 0x1000000>; /* Bank 1 */
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
ingenic,bch-controller = <&bch>;
|
|
|
|
nand@1 {
|
|
reg = <1>;
|
|
|
|
nand-ecc-step-size = <1024>;
|
|
nand-ecc-strength = <24>;
|
|
nand-ecc-mode = "hw";
|
|
nand-on-flash-bbt;
|
|
|
|
rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>;
|
|
wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>;
|
|
|
|
partitions {
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
...
|
|
}
|
|
};
|
|
};
|
|
};
|
|
|
|
The BCH controller is a separate SoC component used for error correction on
|
|
NAND devices. The following is a description of the device properties for a
|
|
BCH controller.
|
|
|
|
Required BCH properties:
|
|
- compatible: Should be set to "ingenic,jz4780-bch".
|
|
- reg: Should specify the BCH controller registers location and length.
|
|
- clocks: Clock for the BCH controller.
|
|
|
|
Example:
|
|
|
|
bch: bch@134d0000 {
|
|
compatible = "ingenic,jz4780-bch";
|
|
reg = <0x134d0000 0x10000>;
|
|
|
|
clocks = <&cgu JZ4780_CLK_BCH>;
|
|
};
|