mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-05 10:36:42 +07:00
a982ac06b0
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4. Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
512 lines
24 KiB
Plaintext
512 lines
24 KiB
Plaintext
AIC7xxx Driver for Linux
|
|
|
|
Introduction
|
|
----------------------------
|
|
The AIC7xxx SCSI driver adds support for Adaptec (http://www.adaptec.com)
|
|
SCSI controllers and chipsets. Major portions of the driver and driver
|
|
development are shared between both Linux and FreeBSD. Support for the
|
|
AIC-7xxx chipsets have been in the default Linux kernel since approximately
|
|
linux-1.1.x and fairly stable since linux-1.2.x, and are also in FreeBSD
|
|
2.1.0 or later.
|
|
|
|
Supported cards/chipsets
|
|
----------------------------
|
|
Adaptec Cards
|
|
----------------------------
|
|
AHA-274x
|
|
AHA-274xT
|
|
AHA-2842
|
|
AHA-2910B
|
|
AHA-2920C
|
|
AHA-2930
|
|
AHA-2930U
|
|
AHA-2930CU
|
|
AHA-2930U2
|
|
AHA-2940
|
|
AHA-2940W
|
|
AHA-2940U
|
|
AHA-2940UW
|
|
AHA-2940UW-PRO
|
|
AHA-2940AU
|
|
AHA-2940U2W
|
|
AHA-2940U2
|
|
AHA-2940U2B
|
|
AHA-2940U2BOEM
|
|
AHA-2944D
|
|
AHA-2944WD
|
|
AHA-2944UD
|
|
AHA-2944UWD
|
|
AHA-2950U2
|
|
AHA-2950U2W
|
|
AHA-2950U2B
|
|
AHA-29160M
|
|
AHA-3940
|
|
AHA-3940U
|
|
AHA-3940W
|
|
AHA-3940UW
|
|
AHA-3940AUW
|
|
AHA-3940U2W
|
|
AHA-3950U2B
|
|
AHA-3950U2D
|
|
AHA-3960D
|
|
AHA-39160M
|
|
AHA-3985
|
|
AHA-3985U
|
|
AHA-3985W
|
|
AHA-3985UW
|
|
|
|
Motherboard Chipsets
|
|
----------------------------
|
|
AIC-777x
|
|
AIC-785x
|
|
AIC-786x
|
|
AIC-787x
|
|
AIC-788x
|
|
AIC-789x
|
|
AIC-3860
|
|
|
|
Bus Types
|
|
----------------------------
|
|
W - Wide SCSI, SCSI-3, 16bit bus, 68pin connector, will also support
|
|
SCSI-1/SCSI-2 50pin devices, transfer rates up to 20MB/s.
|
|
U - Ultra SCSI, transfer rates up to 40MB/s.
|
|
U2- Ultra 2 SCSI, transfer rates up to 80MB/s.
|
|
D - Differential SCSI.
|
|
T - Twin Channel SCSI. Up to 14 SCSI devices.
|
|
|
|
AHA-274x - EISA SCSI controller
|
|
AHA-284x - VLB SCSI controller
|
|
AHA-29xx - PCI SCSI controller
|
|
AHA-394x - PCI controllers with two separate SCSI controllers on-board.
|
|
AHA-398x - PCI RAID controllers with three separate SCSI controllers
|
|
on-board.
|
|
|
|
Not Supported Devices
|
|
------------------------------
|
|
Adaptec Cards
|
|
----------------------------
|
|
AHA-2920 (Only the cards that use the Future Domain chipset are not
|
|
supported, any 2920 cards based on Adaptec AIC chipsets,
|
|
such as the 2920C, are supported)
|
|
AAA-13x Raid Adapters
|
|
AAA-113x Raid Port Card
|
|
|
|
Motherboard Chipsets
|
|
----------------------------
|
|
AIC-7810
|
|
|
|
Bus Types
|
|
----------------------------
|
|
R - Raid Port busses are not supported.
|
|
|
|
The hardware RAID devices sold by Adaptec are *NOT* supported by this
|
|
driver (and will people please stop emailing me about them, they are
|
|
a totally separate beast from the bare SCSI controllers and this driver
|
|
cannot be retrofitted in any sane manner to support the hardware RAID
|
|
features on those cards - Doug Ledford).
|
|
|
|
|
|
People
|
|
------------------------------
|
|
Justin T Gibbs gibbs@plutotech.com
|
|
(BSD Driver Author)
|
|
Dan Eischen deischen@iworks.InterWorks.org
|
|
(Original Linux Driver Co-maintainer)
|
|
Dean Gehnert deang@teleport.com
|
|
(Original Linux FTP/patch maintainer)
|
|
Jess Johnson jester@frenzy.com
|
|
(AIC7xxx FAQ author)
|
|
Doug Ledford dledford@redhat.com
|
|
(Current Linux aic7xxx-5.x.x Driver/Patch/FTP maintainer)
|
|
|
|
Special thanks go to John Aycock (aycock@cpsc.ucalgary.ca), the original
|
|
author of the driver. John has since retired from the project. Thanks
|
|
again for all his work!
|
|
|
|
Mailing list
|
|
------------------------------
|
|
There is a mailing list available for users who want to track development
|
|
and converse with other users and developers. This list is for both
|
|
FreeBSD and Linux support of the AIC7xxx chipsets.
|
|
|
|
To subscribe to the AIC7xxx mailing list send mail to the list server,
|
|
with "subscribe AIC7xxx" in the body (no Subject: required):
|
|
To: majordomo@FreeBSD.ORG
|
|
---
|
|
subscribe AIC7xxx
|
|
|
|
To unsubscribe from the list, send mail to the list server with:
|
|
To: majordomo@FreeBSD.ORG
|
|
---
|
|
unsubscribe AIC7xxx
|
|
|
|
Send regular messages and replies to: AIC7xxx@FreeBSD.ORG
|
|
|
|
Boot Command line options
|
|
------------------------------
|
|
"aic7xxx=no_reset" - Eliminate the SCSI bus reset during startup.
|
|
Some SCSI devices need the initial reset that this option disables
|
|
in order to work. If you have problems at bootup, please make sure
|
|
you aren't using this option.
|
|
|
|
"aic7xxx=reverse_scan" - Certain PCI motherboards scan for devices at
|
|
bootup by scanning from the highest numbered PCI device to the
|
|
lowest numbered PCI device, others do just the opposite and scan
|
|
from lowest to highest numbered PCI device. There is no reliable
|
|
way to autodetect this ordering. So, we default to the most common
|
|
order, which is lowest to highest. Then, in case your motherboard
|
|
scans from highest to lowest, we have this option. If your BIOS
|
|
finds the drives on controller A before controller B but the linux
|
|
kernel finds your drives on controller B before A, then you should
|
|
use this option.
|
|
|
|
"aic7xxx=extended" - Force the driver to detect extended drive translation
|
|
on your controller. This helps those people who have cards without
|
|
a SEEPROM make sure that linux and all other operating systems think
|
|
the same way about your hard drives.
|
|
|
|
"aic7xxx=scbram" - Some cards have external SCB RAM that can be used to
|
|
give the card more hardware SCB slots. This allows the driver to use
|
|
that SCB RAM. Without this option, the driver won't touch the SCB
|
|
RAM because it is known to cause problems on a few cards out there
|
|
(such as 3985 class cards).
|
|
|
|
"aic7xxx=irq_trigger:x" - Replace x with either 0 or 1 to force the kernel
|
|
to use the correct IRQ type for your card. This only applies to EISA
|
|
based controllers. On these controllers, 0 is for Edge triggered
|
|
interrupts, and 1 is for Level triggered interrupts. If you aren't
|
|
sure or don't know which IRQ trigger type your EISA card uses, then
|
|
let the kernel autodetect the trigger type.
|
|
|
|
"aic7xxx=verbose" - This option can be used in one of two ways. If you
|
|
simply specify aic7xxx=verbose, then the kernel will automatically
|
|
pick the default set of verbose messages for you to see.
|
|
Alternatively, you can specify the command as
|
|
"aic7xxx=verbose:0xXXXX" where the X entries are replaced with
|
|
hexadecimal digits. This option is a bit field type option. For
|
|
a full listing of the available options, search for the
|
|
#define VERBOSE_xxxxxx lines in the aic7xxx.c file. If you want
|
|
verbose messages, then it is recommended that you simply use the
|
|
aic7xxx=verbose variant of this command.
|
|
|
|
"aic7xxx=pci_parity:x" - This option controls whether or not the driver
|
|
enables PCI parity error checking on the PCI bus. By default, this
|
|
checking is disabled. To enable the checks, simply specify pci_parity
|
|
with no value afterwords. To reverse the parity from even to odd,
|
|
supply any number other than 0 or 255. In short:
|
|
pci_parity - Even parity checking (even is the normal PCI parity)
|
|
pci_parity:x - Where x > 0, Odd parity checking
|
|
pci_parity:0 - No check (default)
|
|
NOTE: In order to get Even PCI parity checking, you must use the
|
|
version of the option that does not include the : and a number at
|
|
the end (unless you want to enter exactly 2^32 - 1 as the number).
|
|
|
|
"aic7xxx=no_probe" - This option will disable the probing for any VLB
|
|
based 2842 controllers and any EISA based controllers. This is
|
|
needed on certain newer motherboards where the normal EISA I/O ranges
|
|
have been claimed by other PCI devices. Probing on those machines
|
|
will often result in the machine crashing or spontaneously rebooting
|
|
during startup. Examples of machines that need this are the
|
|
Dell PowerEdge 6300 machines.
|
|
|
|
"aic7xxx=seltime:2" - This option controls how long the card waits
|
|
during a device selection sequence for the device to respond.
|
|
The original SCSI spec says that this "should be" 256ms. This
|
|
is generally not required with modern devices. However, some
|
|
very old SCSI I devices need the full 256ms. Most modern devices
|
|
can run fine with only 64ms. The default for this option is
|
|
64ms. If you need to change this option, then use the following
|
|
table to set the proper value in the example above:
|
|
0 - 256ms
|
|
1 - 128ms
|
|
2 - 64ms
|
|
3 - 32ms
|
|
|
|
"aic7xxx=panic_on_abort" - This option is for debugging and will cause
|
|
the driver to panic the linux kernel and freeze the system the first
|
|
time the drivers abort or reset routines are called. This is most
|
|
helpful when some problem causes infinite reset loops that scroll too
|
|
fast to see. By using this option, you can write down what the errors
|
|
actually are and send that information to me so it can be fixed.
|
|
|
|
"aic7xxx=dump_card" - This option will print out the *entire* set of
|
|
configuration registers on the card during the init sequence. This
|
|
is a debugging aid used to see exactly what state the card is in
|
|
when we finally finish our initialization routines. If you don't
|
|
have documentation on the chipsets, this will do you absolutely
|
|
no good unless you are simply trying to write all the information
|
|
down in order to send it to me.
|
|
|
|
"aic7xxx=dump_sequencer" - This is the same as the above options except
|
|
that instead of dumping the register contents on the card, this
|
|
option dumps the contents of the sequencer program RAM. This gives
|
|
the ability to verify that the instructions downloaded to the
|
|
card's sequencer are indeed what they are supposed to be. Again,
|
|
unless you have documentation to tell you how to interpret these
|
|
numbers, then it is totally useless.
|
|
|
|
"aic7xxx=override_term:0xffffffff" - This option is used to force the
|
|
termination on your SCSI controllers to a particular setting. This
|
|
is a bit mask variable that applies for up to 8 aic7xxx SCSI channels.
|
|
Each channel gets 4 bits, divided as follows:
|
|
bit 3 2 1 0
|
|
| | | Enable/Disable Single Ended Low Byte Termination
|
|
| | En/Disable Single Ended High Byte Termination
|
|
| En/Disable Low Byte LVD Termination
|
|
En/Disable High Byte LVD Termination
|
|
|
|
The upper 2 bits that deal with LVD termination only apply to Ultra2
|
|
controllers. Furthermore, due to the current Ultra2 controller
|
|
designs, these bits are tied together such that setting either bit
|
|
enables both low and high byte LVD termination. It is not possible
|
|
to only set high or low byte LVD termination in this manner. This is
|
|
an artifact of the BIOS definition on Ultra2 controllers. For other
|
|
controllers, the only important bits are the two lowest bits. Setting
|
|
the higher bits on non-Ultra2 controllers has no effect. A few
|
|
examples of how to use this option:
|
|
|
|
Enable low and high byte termination on a non-ultra2 controller that
|
|
is the first aic7xxx controller (the correct bits are 0011),
|
|
aic7xxx=override_term:0x3
|
|
|
|
Enable all termination on the third aic7xxx controller, high byte
|
|
termination on the second aic7xxx controller, and low and high byte
|
|
SE termination on the first aic7xxx controller
|
|
(bits are 1111 0010 0011),
|
|
aic7xxx=override_term:0xf23
|
|
|
|
No attempt has been made to make this option non-cryptic. It really
|
|
shouldn't be used except in dire circumstances, and if that happens,
|
|
I'm probably going to be telling you what to set this to anyway :)
|
|
|
|
"aic7xxx=stpwlev:0xffffffff" - This option is used to control the STPWLEV
|
|
bit in the DEVCONFIG PCI register. Currently, this is one of the
|
|
very few registers that we have absolutely *no* way of detecting
|
|
what the variable should be. It depends entirely on how the chipset
|
|
and external terminators were coupled by the card/motherboard maker.
|
|
Further, a chip reset (at power up) always sets this bit to 0. If
|
|
there is no BIOS to run on the chipset/card (such as with a 2910C
|
|
or a motherboard controller with the BIOS totally disabled) then
|
|
the variable may not get set properly. Of course, if the proper
|
|
setting was 0, then that's what it would be after the reset, but if
|
|
the proper setting is actually 1.....you get the picture. Now, since
|
|
we can't detect this at all, I've added this option to force the
|
|
setting. If you have a BIOS on your controller then you should never
|
|
need to use this option. However, if you are having lots of SCSI
|
|
reset problems and can't seem to get them knocked out, this may help.
|
|
|
|
Here's a test to know for certain if you need this option. Make
|
|
a boot floppy that you can use to boot your computer up and that
|
|
will detect the aic7xxx controller. Next, power down your computer.
|
|
While it's down, unplug all SCSI cables from your Adaptec SCSI
|
|
controller. Boot the system back up to the Adaptec EZ-SCSI BIOS
|
|
and then make sure that termination is enabled on your adapter (if
|
|
you have an Adaptec BIOS of course). Next, boot up the floppy you
|
|
made and wait for it to detect the aic7xxx controller. If the kernel
|
|
finds the controller fine, says scsi : x hosts and then tries to
|
|
detect your devices like normal, up to the point where it fails to
|
|
mount your root file system and panics, then you're fine. If, on
|
|
the other hand, the system goes into an infinite reset loop, then
|
|
you need to use this option and/or the previous option to force the
|
|
proper termination settings on your controller. If this happens,
|
|
then you next need to figure out what your settings should be.
|
|
|
|
To find the correct settings, power your machine back down, connect
|
|
back up the SCSI cables, and boot back into your machine like normal.
|
|
However, boot with the aic7xxx=verbose:0x39 option. Record the
|
|
initial DEVCONFIG values for each of your aic7xxx controllers as
|
|
they are listed, and also record what the machine is detecting as
|
|
the proper termination on your controllers. NOTE: the order in
|
|
which the initial DEVCONFIG values are printed out is not guaranteed
|
|
to be the same order as the SCSI controllers are registered. The
|
|
above option and this option both work on the order of the SCSI
|
|
controllers as they are registered, so make sure you match the right
|
|
DEVCONFIG values with the right controllers if you have more than
|
|
one aic7xxx controller.
|
|
|
|
Once you have the detected termination settings and the initial
|
|
DEVCONFIG values for each controller, then figure out what the
|
|
termination on each of the controllers *should* be. Hopefully, that
|
|
part is correct, but it could possibly be wrong if there is
|
|
bogus cable detection logic on your controller or something similar.
|
|
If all the controllers have the correct termination settings, then
|
|
don't set the aic7xxx=override_term variable at all, leave it alone.
|
|
Next, on any controllers that go into an infinite reset loop when
|
|
you unplug all the SCSI cables, get the starting DEVCONFIG value.
|
|
If the initial DEVCONFIG value is divisible by 2, then the correct
|
|
setting for that controller is 0. If it's an odd number, then
|
|
the correct setting for that controller is 1. For any other
|
|
controllers that didn't have an infinite reset problem, then reverse
|
|
the above options. If DEVCONFIG was even, then the correct setting
|
|
is 1, if not then the correct setting is 0.
|
|
|
|
Now that you know what the correct setting was for each controller,
|
|
we need to encode that into the aic7xxx=stpwlev:0x... variable.
|
|
This variable is a bit field encoded variable. Bit 0 is for the first
|
|
aic7xxx controller, bit 1 for the next, etc. Put all these bits
|
|
together and you get a number. For example, if the third aic7xxx
|
|
needed a 1, but the second and first both needed a 0, then the bits
|
|
would be 100 in binary. This then translates to 0x04. You would
|
|
therefore set aic7xxx=stpwlev:0x04. This is fairly standard binary
|
|
to hexadecimal conversions here. If you aren't up to speed on the
|
|
binary->hex conversion then send an email to the aic7xxx mailing
|
|
list and someone can help you out.
|
|
|
|
"aic7xxx=tag_info:{{8,8..},{8,8..},..}" - This option is used to disable
|
|
or enable Tagged Command Queueing (TCQ) on specific devices. As of
|
|
driver version 5.1.11, TCQ is now either on or off by default
|
|
according to the setting you choose during the make config process.
|
|
In order to en/disable TCQ for certain devices at boot time, a user
|
|
may use this boot param. The driver will then parse this message out
|
|
and en/disable the specific device entries that are present based upon
|
|
the value given. The param line is parsed in the following manner:
|
|
|
|
{ - first instance indicates the start of this parameter values
|
|
second instance is the start of entries for a particular
|
|
device entry
|
|
} - end the entries for a particular host adapter, or end the entire
|
|
set of parameter entries
|
|
, - move to next entry. Inside of a set of device entries, this
|
|
moves us to the next device on the list. Outside of device
|
|
entries, this moves us to the next host adapter
|
|
. - Same effect as , but is safe to use with insmod.
|
|
x - the number to enter into the array at this position.
|
|
0 = Enable tagged queueing on this device and use the default
|
|
queue depth
|
|
1-254 = Enable tagged queueing on this device and use this
|
|
number as the queue depth
|
|
255 = Disable tagged queueing on this device.
|
|
Note: anything above 32 for an actual queue depth is wasteful
|
|
and not recommended.
|
|
|
|
A few examples of how this can be used:
|
|
|
|
tag_info:{{8,12,,0,,255,4}}
|
|
This line will only effect the first aic7xxx card registered. It
|
|
will set scsi id 0 to a queue depth of 8, id 1 to 12, leave id 2
|
|
at the default, set id 3 to tagged queueing enabled and use the
|
|
default queue depth, id 4 default, id 5 disabled, and id 6 to 4.
|
|
Any not specified entries stay at the default value, repeated
|
|
commas with no value specified will simply increment to the next id
|
|
without changing anything for the missing values.
|
|
|
|
tag_info:{,,,{,,,255}}
|
|
First, second, and third adapters at default values. Fourth
|
|
adapter, id 3 is disabled. Notice that leading commas simply
|
|
increment what the first number effects, and there are no need
|
|
for trailing commas. When you close out an adapter, or the
|
|
entire entry, anything not explicitly set stays at the default
|
|
value.
|
|
|
|
A final note on this option. The scanner I used for this isn't
|
|
perfect or highly robust. If you mess the line up, the worst that
|
|
should happen is that the line will get ignored. If you don't
|
|
close out the entire entry with the final bracket, then any other
|
|
aic7xxx options after this will get ignored. So, in general, be
|
|
sure of what you are entering, and after you have it right, just
|
|
add it to the lilo.conf file so there won't be any mistakes. As
|
|
a means of checking this parser, the entire tag_info array for
|
|
each card is now printed out in the /proc/scsi/aic7xxx/x file. You
|
|
can use that to verify that your options were parsed correctly.
|
|
|
|
Boot command line options may be combined to form the proper set of options
|
|
a user might need. For example, the following is valid:
|
|
|
|
aic7xxx=verbose,extended,irq_trigger:1
|
|
|
|
The only requirement is that individual options be separated by a comma or
|
|
a period on the command line.
|
|
|
|
Module Loading command options
|
|
------------------------------
|
|
When loading the aic7xxx driver as a module, the exact same options are
|
|
available to the user. However, the syntax to specify the options changes
|
|
slightly. For insmod, you need to wrap the aic7xxx= argument in quotes
|
|
and replace all ',' with '.'. So, for example, a valid insmod line
|
|
would be:
|
|
|
|
insmod aic7xxx aic7xxx='verbose.irq_trigger:1.extended'
|
|
|
|
This line should result in the *exact* same behaviour as if you typed
|
|
it in at the lilo prompt and the driver was compiled into the kernel
|
|
instead of being a module. The reason for the single quote is so that
|
|
the shell won't try to interpret anything in the line, such as {.
|
|
Insmod assumes any options starting with a letter instead of a number
|
|
is a character string (which is what we want) and by switching all of
|
|
the commas to periods, insmod won't interpret this as more than one
|
|
string and write junk into our binary image. I consider it a bug in
|
|
the insmod program that even if you wrap your string in quotes (quotes
|
|
that pass the shell mind you and that insmod sees) it still treats
|
|
a comma inside of those quotes as starting a new variable, resulting
|
|
in memory scribbles if you don't switch the commas to periods.
|
|
|
|
|
|
Kernel Compile options
|
|
------------------------------
|
|
The various kernel compile time options for this driver are now fairly
|
|
well documented in the file Documentation/Configure.help. In order to
|
|
see this documentation, you need to use one of the advanced configuration
|
|
programs (menuconfig and xconfig). If you are using the "make menuconfig"
|
|
method of configuring your kernel, then you would simply highlight the
|
|
option in question and hit the ? key. If you are using the "make xconfig"
|
|
method of configuring your kernel, then simply click on the help button
|
|
next to the option you have questions about. The help information from
|
|
the Configure.help file will then get automatically displayed.
|
|
|
|
/proc support
|
|
------------------------------
|
|
The /proc support for the AIC7xxx can be found in the /proc/scsi/aic7xxx/
|
|
directory. That directory contains a file for each SCSI controller in
|
|
the system. Each file presents the current configuration and transfer
|
|
statistics (enabled with #define in aic7xxx.c) for each controller.
|
|
|
|
Thanks to Michael Neuffer for his upper-level SCSI help, and
|
|
Matthew Jacob for statistics support.
|
|
|
|
Debugging the driver
|
|
------------------------------
|
|
Should you have problems with this driver, and would like some help in
|
|
getting them solved, there are a couple debugging items built into
|
|
the driver to facilitate getting the needed information from the system.
|
|
In general, I need a complete description of the problem, with as many
|
|
logs as possible concerning what happens. To help with this, there is
|
|
a command option aic7xxx=panic_on_abort. This option, when set, forces
|
|
the driver to panic the kernel on the first SCSI abort issued by the
|
|
mid level SCSI code. If your system is going to reset loops and you
|
|
can't read the screen, then this is what you need. Not only will it
|
|
stop the system, but it also prints out a large amount of state
|
|
information in the process. Second, if you specify the option
|
|
"aic7xxx=verbose:0x1ffff", the system will print out *SOOOO* much
|
|
information as it runs that you won't be able to see anything.
|
|
However, this can actually be very useful if your machine simply
|
|
locks up when trying to boot, since it will pin-point what was last
|
|
happening (in regards to the aic7xxx driver) immediately prior to
|
|
the lockup. This is really only useful if your machine simply can
|
|
not boot up successfully. If you can get your machine to run, then
|
|
this will produce far too much information.
|
|
|
|
FTP sites
|
|
------------------------------
|
|
ftp://ftp.redhat.com/pub/aic/
|
|
- Out of date. I used to keep stuff here, but too many people
|
|
complained about having a hard time getting into Red Hat's ftp
|
|
server. So use the web site below instead.
|
|
ftp://ftp.pcnet.com/users/eischen/Linux/
|
|
- Dan Eischen's driver distribution area
|
|
ftp://ekf2.vsb.cz/pub/linux/kernel/aic7xxx/ftp.teleport.com/
|
|
- European Linux mirror of Teleport site
|
|
|
|
Web sites
|
|
------------------------------
|
|
http://people.redhat.com/dledford/
|
|
- My web site, also the primary aic7xxx site with several related
|
|
pages.
|
|
|
|
Dean W. Gehnert
|
|
deang@teleport.com
|
|
|
|
$Revision: 3.0 $
|
|
|
|
Modified by Doug Ledford 1998-2000
|
|
|