linux_dsm_epyc7002/drivers/usb/musb/musbhsdma.c
Paul Cercueil c80d0f4426 usb: musb: dma: Correct parameter passed to IRQ handler
The IRQ handler was passed a pointer to a struct dma_controller, but the
argument was then casted to a pointer to a struct musb_dma_controller.

Fixes: 427c4f3334 ("usb: struct device - replace bus_id with dev_name(), dev_set_name()")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20191216161844.772-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-30 19:54:57 +01:00

440 lines
12 KiB
C

// SPDX-License-Identifier: GPL-2.0
/*
* MUSB OTG driver - support for Mentor's DMA controller
*
* Copyright 2005 Mentor Graphics Corporation
* Copyright (C) 2005-2007 by Texas Instruments
*/
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include "musb_core.h"
#define MUSB_HSDMA_BASE 0x200
#define MUSB_HSDMA_INTR (MUSB_HSDMA_BASE + 0)
#define MUSB_HSDMA_CONTROL 0x4
#define MUSB_HSDMA_ADDRESS 0x8
#define MUSB_HSDMA_COUNT 0xc
#define MUSB_HSDMA_CHANNEL_OFFSET(_bchannel, _offset) \
(MUSB_HSDMA_BASE + (_bchannel << 4) + _offset)
#define musb_read_hsdma_addr(mbase, bchannel) \
musb_readl(mbase, \
MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_ADDRESS))
#define musb_write_hsdma_addr(mbase, bchannel, addr) \
musb_writel(mbase, \
MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_ADDRESS), \
addr)
#define musb_read_hsdma_count(mbase, bchannel) \
musb_readl(mbase, \
MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_COUNT))
#define musb_write_hsdma_count(mbase, bchannel, len) \
musb_writel(mbase, \
MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_COUNT), \
len)
/* control register (16-bit): */
#define MUSB_HSDMA_ENABLE_SHIFT 0
#define MUSB_HSDMA_TRANSMIT_SHIFT 1
#define MUSB_HSDMA_MODE1_SHIFT 2
#define MUSB_HSDMA_IRQENABLE_SHIFT 3
#define MUSB_HSDMA_ENDPOINT_SHIFT 4
#define MUSB_HSDMA_BUSERROR_SHIFT 8
#define MUSB_HSDMA_BURSTMODE_SHIFT 9
#define MUSB_HSDMA_BURSTMODE (3 << MUSB_HSDMA_BURSTMODE_SHIFT)
#define MUSB_HSDMA_BURSTMODE_UNSPEC 0
#define MUSB_HSDMA_BURSTMODE_INCR4 1
#define MUSB_HSDMA_BURSTMODE_INCR8 2
#define MUSB_HSDMA_BURSTMODE_INCR16 3
#define MUSB_HSDMA_CHANNELS 8
struct musb_dma_controller;
struct musb_dma_channel {
struct dma_channel channel;
struct musb_dma_controller *controller;
u32 start_addr;
u32 len;
u16 max_packet_sz;
u8 idx;
u8 epnum;
u8 transmit;
};
struct musb_dma_controller {
struct dma_controller controller;
struct musb_dma_channel channel[MUSB_HSDMA_CHANNELS];
void *private_data;
void __iomem *base;
u8 channel_count;
u8 used_channels;
int irq;
};
static void dma_channel_release(struct dma_channel *channel);
static void dma_controller_stop(struct musb_dma_controller *controller)
{
struct musb *musb = controller->private_data;
struct dma_channel *channel;
u8 bit;
if (controller->used_channels != 0) {
dev_err(musb->controller,
"Stopping DMA controller while channel active\n");
for (bit = 0; bit < MUSB_HSDMA_CHANNELS; bit++) {
if (controller->used_channels & (1 << bit)) {
channel = &controller->channel[bit].channel;
dma_channel_release(channel);
if (!controller->used_channels)
break;
}
}
}
}
static struct dma_channel *dma_channel_allocate(struct dma_controller *c,
struct musb_hw_ep *hw_ep, u8 transmit)
{
struct musb_dma_controller *controller = container_of(c,
struct musb_dma_controller, controller);
struct musb_dma_channel *musb_channel = NULL;
struct dma_channel *channel = NULL;
u8 bit;
for (bit = 0; bit < MUSB_HSDMA_CHANNELS; bit++) {
if (!(controller->used_channels & (1 << bit))) {
controller->used_channels |= (1 << bit);
musb_channel = &(controller->channel[bit]);
musb_channel->controller = controller;
musb_channel->idx = bit;
musb_channel->epnum = hw_ep->epnum;
musb_channel->transmit = transmit;
channel = &(musb_channel->channel);
channel->private_data = musb_channel;
channel->status = MUSB_DMA_STATUS_FREE;
channel->max_len = 0x100000;
/* Tx => mode 1; Rx => mode 0 */
channel->desired_mode = transmit;
channel->actual_len = 0;
break;
}
}
return channel;
}
static void dma_channel_release(struct dma_channel *channel)
{
struct musb_dma_channel *musb_channel = channel->private_data;
channel->actual_len = 0;
musb_channel->start_addr = 0;
musb_channel->len = 0;
musb_channel->controller->used_channels &=
~(1 << musb_channel->idx);
channel->status = MUSB_DMA_STATUS_UNKNOWN;
}
static void configure_channel(struct dma_channel *channel,
u16 packet_sz, u8 mode,
dma_addr_t dma_addr, u32 len)
{
struct musb_dma_channel *musb_channel = channel->private_data;
struct musb_dma_controller *controller = musb_channel->controller;
struct musb *musb = controller->private_data;
void __iomem *mbase = controller->base;
u8 bchannel = musb_channel->idx;
u16 csr = 0;
musb_dbg(musb, "%p, pkt_sz %d, addr %pad, len %d, mode %d",
channel, packet_sz, &dma_addr, len, mode);
if (mode) {
csr |= 1 << MUSB_HSDMA_MODE1_SHIFT;
BUG_ON(len < packet_sz);
}
csr |= MUSB_HSDMA_BURSTMODE_INCR16
<< MUSB_HSDMA_BURSTMODE_SHIFT;
csr |= (musb_channel->epnum << MUSB_HSDMA_ENDPOINT_SHIFT)
| (1 << MUSB_HSDMA_ENABLE_SHIFT)
| (1 << MUSB_HSDMA_IRQENABLE_SHIFT)
| (musb_channel->transmit
? (1 << MUSB_HSDMA_TRANSMIT_SHIFT)
: 0);
/* address/count */
musb_write_hsdma_addr(mbase, bchannel, dma_addr);
musb_write_hsdma_count(mbase, bchannel, len);
/* control (this should start things) */
musb_writew(mbase,
MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_CONTROL),
csr);
}
static int dma_channel_program(struct dma_channel *channel,
u16 packet_sz, u8 mode,
dma_addr_t dma_addr, u32 len)
{
struct musb_dma_channel *musb_channel = channel->private_data;
struct musb_dma_controller *controller = musb_channel->controller;
struct musb *musb = controller->private_data;
musb_dbg(musb, "ep%d-%s pkt_sz %d, dma_addr %pad length %d, mode %d",
musb_channel->epnum,
musb_channel->transmit ? "Tx" : "Rx",
packet_sz, &dma_addr, len, mode);
BUG_ON(channel->status == MUSB_DMA_STATUS_UNKNOWN ||
channel->status == MUSB_DMA_STATUS_BUSY);
/*
* The DMA engine in RTL1.8 and above cannot handle
* DMA addresses that are not aligned to a 4 byte boundary.
* It ends up masking the last two bits of the address
* programmed in DMA_ADDR.
*
* Fail such DMA transfers, so that the backup PIO mode
* can carry out the transfer
*/
if ((musb->hwvers >= MUSB_HWVERS_1800) && (dma_addr % 4))
return false;
channel->actual_len = 0;
musb_channel->start_addr = dma_addr;
musb_channel->len = len;
musb_channel->max_packet_sz = packet_sz;
channel->status = MUSB_DMA_STATUS_BUSY;
configure_channel(channel, packet_sz, mode, dma_addr, len);
return true;
}
static int dma_channel_abort(struct dma_channel *channel)
{
struct musb_dma_channel *musb_channel = channel->private_data;
void __iomem *mbase = musb_channel->controller->base;
struct musb *musb = musb_channel->controller->private_data;
u8 bchannel = musb_channel->idx;
int offset;
u16 csr;
if (channel->status == MUSB_DMA_STATUS_BUSY) {
if (musb_channel->transmit) {
offset = musb->io.ep_offset(musb_channel->epnum,
MUSB_TXCSR);
/*
* The programming guide says that we must clear
* the DMAENAB bit before the DMAMODE bit...
*/
csr = musb_readw(mbase, offset);
csr &= ~(MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAENAB);
musb_writew(mbase, offset, csr);
csr &= ~MUSB_TXCSR_DMAMODE;
musb_writew(mbase, offset, csr);
} else {
offset = musb->io.ep_offset(musb_channel->epnum,
MUSB_RXCSR);
csr = musb_readw(mbase, offset);
csr &= ~(MUSB_RXCSR_AUTOCLEAR |
MUSB_RXCSR_DMAENAB |
MUSB_RXCSR_DMAMODE);
musb_writew(mbase, offset, csr);
}
musb_writew(mbase,
MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_CONTROL),
0);
musb_write_hsdma_addr(mbase, bchannel, 0);
musb_write_hsdma_count(mbase, bchannel, 0);
channel->status = MUSB_DMA_STATUS_FREE;
}
return 0;
}
static irqreturn_t dma_controller_irq(int irq, void *private_data)
{
struct musb_dma_controller *controller = private_data;
struct musb *musb = controller->private_data;
struct musb_dma_channel *musb_channel;
struct dma_channel *channel;
void __iomem *mbase = controller->base;
irqreturn_t retval = IRQ_NONE;
unsigned long flags;
u8 bchannel;
u8 int_hsdma;
u32 addr, count;
u16 csr;
spin_lock_irqsave(&musb->lock, flags);
int_hsdma = musb_readb(mbase, MUSB_HSDMA_INTR);
if (!int_hsdma) {
musb_dbg(musb, "spurious DMA irq");
for (bchannel = 0; bchannel < MUSB_HSDMA_CHANNELS; bchannel++) {
musb_channel = (struct musb_dma_channel *)
&(controller->channel[bchannel]);
channel = &musb_channel->channel;
if (channel->status == MUSB_DMA_STATUS_BUSY) {
count = musb_read_hsdma_count(mbase, bchannel);
if (count == 0)
int_hsdma |= (1 << bchannel);
}
}
musb_dbg(musb, "int_hsdma = 0x%x", int_hsdma);
if (!int_hsdma)
goto done;
}
for (bchannel = 0; bchannel < MUSB_HSDMA_CHANNELS; bchannel++) {
if (int_hsdma & (1 << bchannel)) {
musb_channel = (struct musb_dma_channel *)
&(controller->channel[bchannel]);
channel = &musb_channel->channel;
csr = musb_readw(mbase,
MUSB_HSDMA_CHANNEL_OFFSET(bchannel,
MUSB_HSDMA_CONTROL));
if (csr & (1 << MUSB_HSDMA_BUSERROR_SHIFT)) {
musb_channel->channel.status =
MUSB_DMA_STATUS_BUS_ABORT;
} else {
u8 devctl;
addr = musb_read_hsdma_addr(mbase,
bchannel);
channel->actual_len = addr
- musb_channel->start_addr;
musb_dbg(musb, "ch %p, 0x%x -> 0x%x (%zu / %d) %s",
channel, musb_channel->start_addr,
addr, channel->actual_len,
musb_channel->len,
(channel->actual_len
< musb_channel->len) ?
"=> reconfig 0" : "=> complete");
devctl = musb_readb(mbase, MUSB_DEVCTL);
channel->status = MUSB_DMA_STATUS_FREE;
/* completed */
if (musb_channel->transmit &&
(!channel->desired_mode ||
(channel->actual_len %
musb_channel->max_packet_sz))) {
u8 epnum = musb_channel->epnum;
int offset = musb->io.ep_offset(epnum,
MUSB_TXCSR);
u16 txcsr;
/*
* The programming guide says that we
* must clear DMAENAB before DMAMODE.
*/
musb_ep_select(mbase, epnum);
txcsr = musb_readw(mbase, offset);
if (channel->desired_mode == 1) {
txcsr &= ~(MUSB_TXCSR_DMAENAB
| MUSB_TXCSR_AUTOSET);
musb_writew(mbase, offset, txcsr);
/* Send out the packet */
txcsr &= ~MUSB_TXCSR_DMAMODE;
txcsr |= MUSB_TXCSR_DMAENAB;
}
txcsr |= MUSB_TXCSR_TXPKTRDY;
musb_writew(mbase, offset, txcsr);
}
musb_dma_completion(musb, musb_channel->epnum,
musb_channel->transmit);
}
}
}
retval = IRQ_HANDLED;
done:
spin_unlock_irqrestore(&musb->lock, flags);
return retval;
}
void musbhs_dma_controller_destroy(struct dma_controller *c)
{
struct musb_dma_controller *controller = container_of(c,
struct musb_dma_controller, controller);
dma_controller_stop(controller);
if (controller->irq)
free_irq(controller->irq, c);
kfree(controller);
}
EXPORT_SYMBOL_GPL(musbhs_dma_controller_destroy);
struct dma_controller *musbhs_dma_controller_create(struct musb *musb,
void __iomem *base)
{
struct musb_dma_controller *controller;
struct device *dev = musb->controller;
struct platform_device *pdev = to_platform_device(dev);
int irq = platform_get_irq_byname(pdev, "dma");
if (irq <= 0) {
dev_err(dev, "No DMA interrupt line!\n");
return NULL;
}
controller = kzalloc(sizeof(*controller), GFP_KERNEL);
if (!controller)
return NULL;
controller->channel_count = MUSB_HSDMA_CHANNELS;
controller->private_data = musb;
controller->base = base;
controller->controller.channel_alloc = dma_channel_allocate;
controller->controller.channel_release = dma_channel_release;
controller->controller.channel_program = dma_channel_program;
controller->controller.channel_abort = dma_channel_abort;
if (request_irq(irq, dma_controller_irq, 0,
dev_name(musb->controller), controller)) {
dev_err(dev, "request_irq %d failed!\n", irq);
musb_dma_controller_destroy(&controller->controller);
return NULL;
}
controller->irq = irq;
return &controller->controller;
}
EXPORT_SYMBOL_GPL(musbhs_dma_controller_create);