mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-26 18:55:26 +07:00
7989b4bb23
The AD7616 is a 12-bit ADC with 16 channels. The AD7616 can be configured to work in hardware mode by controlling it via gpio pins and read data via spi. No support for software mode yet, but it is a work in progress. This device requires a reset in order to update oversampling, so chip info has got a new attribute to mark this. The current assumption that this driver makes for AD7616, is that it's working in Hardware Mode with Serial, Burst and Sequencer modes activated. To activate them, following pins must be pulled high: -SER/PAR -SEQEN And following must be pulled low: -WR/BURST -DB4/SEQEN Datasheets: Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7616.pdf Signed-off-by: Beniamin Bia <beniamin.bia@analog.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
115 lines
3.7 KiB
C
115 lines
3.7 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
/*
|
|
* AD7606 ADC driver
|
|
*
|
|
* Copyright 2011 Analog Devices Inc.
|
|
*/
|
|
|
|
#ifndef IIO_ADC_AD7606_H_
|
|
#define IIO_ADC_AD7606_H_
|
|
|
|
/**
|
|
* struct ad7606_chip_info - chip specific information
|
|
* @channels: channel specification
|
|
* @num_channels: number of channels
|
|
* @oversampling_avail pointer to the array which stores the available
|
|
* oversampling ratios.
|
|
* @oversampling_num number of elements stored in oversampling_avail array
|
|
* @os_req_reset some devices require a reset to update oversampling
|
|
*/
|
|
struct ad7606_chip_info {
|
|
const struct iio_chan_spec *channels;
|
|
unsigned int num_channels;
|
|
const unsigned int *oversampling_avail;
|
|
unsigned int oversampling_num;
|
|
bool os_req_reset;
|
|
};
|
|
|
|
/**
|
|
* struct ad7606_state - driver instance specific data
|
|
* @dev pointer to kernel device
|
|
* @chip_info entry in the table of chips that describes this device
|
|
* @reg regulator info for the the power supply of the device
|
|
* @bops bus operations (SPI or parallel)
|
|
* @range voltage range selection, selects which scale to apply
|
|
* @oversampling oversampling selection
|
|
* @base_address address from where to read data in parallel operation
|
|
* @scale_avail pointer to the array which stores the available scales
|
|
* @num_scales number of elements stored in the scale_avail array
|
|
* @oversampling_avail pointer to the array which stores the available
|
|
* oversampling ratios.
|
|
* @num_os_ratios number of elements stored in oversampling_avail array
|
|
* @lock protect sensor state from concurrent accesses to GPIOs
|
|
* @gpio_convst GPIO descriptor for conversion start signal (CONVST)
|
|
* @gpio_reset GPIO descriptor for device hard-reset
|
|
* @gpio_range GPIO descriptor for range selection
|
|
* @gpio_standby GPIO descriptor for stand-by signal (STBY),
|
|
* controls power-down mode of device
|
|
* @gpio_frstdata GPIO descriptor for reading from device when data
|
|
* is being read on the first channel
|
|
* @gpio_os GPIO descriptors to control oversampling on the device
|
|
* @complete completion to indicate end of conversion
|
|
* @trig The IIO trigger associated with the device.
|
|
* @data buffer for reading data from the device
|
|
*/
|
|
struct ad7606_state {
|
|
struct device *dev;
|
|
const struct ad7606_chip_info *chip_info;
|
|
struct regulator *reg;
|
|
const struct ad7606_bus_ops *bops;
|
|
unsigned int range;
|
|
unsigned int oversampling;
|
|
void __iomem *base_address;
|
|
const unsigned int *scale_avail;
|
|
unsigned int num_scales;
|
|
const unsigned int *oversampling_avail;
|
|
unsigned int num_os_ratios;
|
|
|
|
struct mutex lock; /* protect sensor state */
|
|
struct gpio_desc *gpio_convst;
|
|
struct gpio_desc *gpio_reset;
|
|
struct gpio_desc *gpio_range;
|
|
struct gpio_desc *gpio_standby;
|
|
struct gpio_desc *gpio_frstdata;
|
|
struct gpio_descs *gpio_os;
|
|
struct iio_trigger *trig;
|
|
struct completion completion;
|
|
|
|
/*
|
|
* DMA (thus cache coherency maintenance) requires the
|
|
* transfer buffers to live in their own cache lines.
|
|
* 16 * 16-bit samples + 64-bit timestamp
|
|
*/
|
|
unsigned short data[20] ____cacheline_aligned;
|
|
};
|
|
|
|
/**
|
|
* struct ad7606_bus_ops - driver bus operations
|
|
* @read_block function pointer for reading blocks of data
|
|
*/
|
|
struct ad7606_bus_ops {
|
|
/* more methods added in future? */
|
|
int (*read_block)(struct device *dev, int num, void *data);
|
|
};
|
|
|
|
int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
|
|
const char *name, unsigned int id,
|
|
const struct ad7606_bus_ops *bops);
|
|
|
|
enum ad7606_supported_device_ids {
|
|
ID_AD7605_4,
|
|
ID_AD7606_8,
|
|
ID_AD7606_6,
|
|
ID_AD7606_4,
|
|
ID_AD7616,
|
|
};
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
extern const struct dev_pm_ops ad7606_pm_ops;
|
|
#define AD7606_PM_OPS (&ad7606_pm_ops)
|
|
#else
|
|
#define AD7606_PM_OPS NULL
|
|
#endif
|
|
|
|
#endif /* IIO_ADC_AD7606_H_ */
|